Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lorena Zichella has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Influence of Biofibres and Biomass Ash from Agricultural Wastes on Microstructure and Mechanical Properties of Cement-Based Composites

    by Lorena Zichella, Daria Jóźwiak-Niedźwiedzka, Rossana Bellopede, Santina Vadalà, Alessandro P. Fantilli

  • Open Access

    Ornamental Stone Cutting Processing and Sludge Production Evaluation with the Goal of Ending Waste

    by Lorena Zichella, Rossana Bellopede, Paola Marini

    In the quarry sector, the reduction of landfill material may be obtained not only by finding a suitable recovery of the material as a by-product, but also by identifying the best available cutting technique to be used on the basis of the physical, chemical, and mechanical characteristics of the stones. The choice of the best cutting technique could lead to high efficiency and performance, high quality of the cut surfaces, and a very low environmental impact by reducing energy consumption, decreasing the concentration of heavy metals in the sludge, and producing less waste. In this context, an analysis of the procedures for cutting different types of ornamental stones into slabs together with the evaluation of sludge production for the different cutting methods has been carried out. Two types of analysis were carried out in parallel: evaluation of the stones workability and calculation of the amount of sludge produced in the three different cutting technologies and from the cutting of blocks. A comparison was carried out on the quality of the sludge produced, on type and quantity of metals present, taking into account the different cutting technologies. The performed tests were: chemical analysis, magnetic separation test, and SEM analysis of the metal fraction. The study could provide stone producers with a technological, scientific instrument to identify the best cutting techniques for the processing of their stones, in order to obtain a high-efficiency process, optimize the recovery process, increase the economic advantages, and evaluate the possible reuse of the sludge through a proactive waste management strategy.


  • Open Access

    Vinyl-Asbestos Floor Risk Exposure in Three Different Simulations

    by Lorena Zichella, Fiorenza Baudana, Giovanna Zanetti, Paola Marini

    Vinyl floors are widely used in public areas for their low cost and easy cleaning. From 1960 to 1980, asbestos was often added to improve vinyl floor performances. The Italian Ministerial Decree (M.D.) 06/09/94 indicates asbestos vinyl tiles as non-friable materials and, therefore, few dangerous to human health. This work aims to check through three different experimental tests if asbestos floor tiles, after decades of use, maintain their characteristics of compactness and non-friability. The effect of a small stone fragment stuck in the sole of rubber shoes was reproduced by striking the vinyl floor with a crampon. A vinyl tile was broken into smaller pieces with the aid of pliers to simulate what normally happens when workers replace the floors or sample it to verify the presence of asbestos. The third test reproduced the abrasion of the tile surface due to the dragging of furniture or heavy materials or sand grains that remain attached to the soles of shoes. The tests were carried out in safe conditions, working under an extractor hood with a glove box. Airborne sampling in the hood obtained the concentration of asbestos fibers produced in each test. The simulation tests performed confirms the possible release of fibers if the vinyl tiles are cut, abraded or perforated, as indicated by the Italian M.D.


  • Open Access

    Performance-Related Assessment of the Potential Use of Sawing Sludge in Cementitious Fluidized Thermal Backfills

    by Lorena Zichella, Eldho Choorackal, Michela Airoldi, Pier Paolo Riviera, Rossana Bellopede, Ezio Santagata

    The management of sawing sludge originated from cutting operations of ornamental stones represents a challenging task as a consequence of its peculiar composition that includes non-negligible amounts of heavy metals resulting from the wear and tear of cutting tools. The aim of the research work presented in this paper was to investigate the feasibility of using these by-products as supplementary constituents of cementitious mixtures employed for the formation of Fluidized Thermal Backfills (FTB). These mixtures are designed and produced for filling operations in pavement subgrades in which high-voltage electrical transmission cables are buried for protection purposes. Two different types of sawing sludge were thoroughly analyzed from a physical and chemical point of view and thereafter employed for the laboratory production of four FTB mixtures. Then, these were subjected to thermal, mechanical, and environmental tests in order to verify their suitability for their intended use. All investigated FTB mixtures exhibited a satisfactory and stable thermal conductivity, and they also displayed enhanced stiffness properties in comparison to standard subgrade and sub-base materials. Controversial results were obtained with respect to environmental properties resulting from leaching tests, thus suggesting that further investigations are needed before any full-scale application can take place.


  • Marble Durability Assessment by Means of Total Optical Porosity and Adjacent Grain Analysis

    by Rossana Bellopede, Lorena Zichella, Paola Marini

    The presence of pores, cracks and microcracks in marble is one of the main features that govern the processes of decay of this stone material and, although marble is characterised by a modest porosity, there is a clear correlation between the presence and movement of fluids, and the phenomena of alteration. Through the study of porosity, it is possible to better understand the phenomena of alteration and degradation in order to obtain useful information, not only in the field of modern building, but also for the protection and recovery of historical and artistic heritage goods. This study was conducted through the characterisation of parameters directly related with the degree of alteration of the materials: water absorption at atmospheric pressure (EN 13755), open porosity (EN 1936), flexural strength (EN 12372) and bowing (EN 16306 par. 8.2). The physical and mechanical measurements have been compared with the Total Optical Porosity method (TOP) and the Adjacent Grain Analysis (AGA) index (a suggested method to evaluate the marbles’ tendency to bow, in EN 16306 annex C); two different methodologies both based on image analysis. The purpose of this study is to demonstrate the effectiveness, for the assessment of marble durability, of the two techniques of microscopic image analysis, the first correlating to the grain shape and the second to the open porosity index. This was done by comparing the microscopic image analysis results with the physical and mechanical properties, both after artificial ageing and after ten years of natural ageing. The results obtained with the TOP method seem to represent the tendency to decay better than the AGA index. The comparison of image analysis of the thin sections, in different portions of the marble specimens, shows the development of degradation due to atmospheric agents, from the surface to the inside, of naturally aged specimens, confirming recent studies made on different marbles.


  • Open Access

    Ornamental stone cutting processing and sludge production evaluation with the goal of ending waste.

    by Lorena Zichella, Rossana Bellopede, Paola Marini

    The End-of-waste concept was introduced by the ‘Thematic Strategy on the prevention and recycling of waste’ adopted by the European Commission, in which it proposed to specify the conditions for the cessation of waste status as part of the revision of the Waste Framework Directive (Directive 2008/98/EC). The Directive states that a waste shall lose its status if it is submitted to a recovery operation (including recycling) and comply with specific eligibility criteria. The strategic goal of the End-of-waste is to promote recycling, helping to ensure a high level of environmental protection through the reduction of the consumption of critical raw materials and the quantities of waste destined for disposal.In the mining sector, the reduction of landfill material may be obtained not only by finding a suitable recovery of the material as a by-product, but also identifying the best available cutting technique to be used on the basis of the physical, chemical and mechanical characteristics of the stones. The choice of the best cutting technique could lead to high efficiency and performance, high quality of the cut surfaces and a very low environmental impact by reducing energy consumption, decreasing the concentration of heavy metals in the sludge and producing less waste.In this context, an analysis of the procedures for cutting different types of ornamental stones into slabs together with the evaluation of sludge production for the different cutting methods has been carried out.Three types of analysis were conducted in parallel. The first concerns the characterization of the stones and the choice of the type of cutting machine. The analyses carried out were: petrographic analysis, compression strength, flexural strength, apparent density and water absorption. Also ultrasonic pulse velocity (UPV) and Knoop analyses were performed in order to establish the workability class of the stones, and their classification in accordance with previous research works (EASE R3).The second analysis involves calculating the amount of sludge produced in the three different cutting technologies, taking into account the same block characteristics. The third analysis was conducted on the sludge resulting from the processing of blocks cut into slabs. A comparison was carried out on the quality of the sludge produced, or type and quantity of metals present, taking into account the three different technologies. The tests carried out were: chemical analysis, magnetic separation test and SEM analysis of the metal fraction.The study could provide stone producers with a technological, scientific instrument to identify the best cutting techniques for the processing of their stones, in order to obtain a good efficiency process, optimize the recovery process, increase the economic advantages, and evaluate the possible reuse of the sludge through a proactive waste management strategy.


  • Open Access

    Silicate Sawing Sludge Recovery in Thermo Eco-Mortar for Macroporous Plaster

    by Lorena Zichella, Paolo Marone, Pasquale Buonanno, Marco D’amore, Rossana Bellopede

    The aim of this research was to develop a new eco-product to find a correct recovery of silicate sawing sludge by means of waste management according to European criteria. To reach this goal, a thermal eco-mortar for a macroporous plaster was developed. The main characteristics of a plaster that influence the correct choice of the mortar are good adherence with underlying support, impermeability, thermal and acoustic insulation, mechanical resistance and ability to allow transpiration processes through the wall’s perimeters. Plaster is a mortar composed of a binding part that incorporates sand with a selected particle size distribution, not greater than 2 mm. The sludge, to be used as plaster, must satisfy requirements related to thermal insulation, resistance to moisture, mechanical resistance and good injection. For this purpose, low-content metals sludge, derived from the Luserna stone flaming and cutting slabs, are to be reused as a substitute for the sands and fine particles, respectively, that are normally used to produce plasters. The laboratory tests carried out on the finished product, in accordance with European standards, are as follows: water absorption, specific density, flexural and compressive strength, before and after freeze and thaw cycles, pull out, salt crystallisation cycle resistance and thermal conductivity. Chemical and leaching tests were carried out to verify the possible release of heavy metals into the environment after installation. The product quality was demonstrated as the cement mortars, incorporating the metals, did not allow their release in nature. A sludge recovery, in an unaltered state, was provided to reduce any costs connected to a pre-treatment and to make recovery economically advantageous for the stone sector.


  • Open Access

    Glass Waste3: A Preliminary Study for a New Industrial Recovery Processing

    by Rossana Bellopede, Lorena Zichella, Paola Marini

    In recent times, the selection and treatment of glass waste are implemented in processing plants where a secondary raw material (SRM) named glass cullet, which is suitable for glass production, and a waste containing a high percentage of glass (glass waste2) is obtained. In the literature, there are many studies conducted on the recovery of the cullet, while few are the studies on the recovery of the waste that is produced by cullet processing. According to the 2013 Joint Research Centre (JRC) Reference report, the cullet produces savings in terms of energy and raw materials. However, it has a high current cost and its availability is becoming difficult, therefore its use is not always economically advantageous. The goal and strategy of the European Union is zero waste. For this purpose, further treatment of glass waste has been investigated. Through the industrial treatment of the glass waste2, a glass waste3 constituted again by an SRM made of glass is obtained together with a high quantity of presumed SRM (e.g., heavy plastic, corks, iron, non-ferrous metals, etc.). The process treatment separating these SRMs from the glass waste3 is, in this case, a pilot plant that needs to be optimized in order to reach an economic and sustainable industrial process solution. In particular, the materials to be recycled are exploitable product fractions with different particle sizes and physical properties (such as density, shape and resistance). This research is based on data collected from a North Italy process plant and is aimed at solving the issue of waste in this kind of process by implementing a pilot plant already present. Representative samples of feed material (glass waste3) and different products of the pilot plant have been analyzed. Moreover, laboratory tests were executed to improve separation efficiency and to valorize the different product fractions. A flow sheet of a new treatment plant has been developed and an economic evaluation has been made. The materials that will be separated in the new plant could be traded as SRM—e.g., plastics, metals, synthetic and cork stoppers—which constitute almost 90% of the total feed of the plant.