Dong-Song Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dong-Song Yin has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Yilin Yang
Graduate department Jiamusi University Jiamusi 154000 China
2 shared publicationsYuting Zhou
School of Materials Science and Engineering Guangdong Ocean University (Yangjiang) Yangjiang 529500 China
2 shared publicationsAi-Lian Liu
Heilongjiang University of Science and Technology
1 shared publicationChao Lu
1 shared publication- Dongsong Yin
School of Materials Science and Engineering Guangdong Ocean University (Yangjiang) Yangjiang 529500 China
1 shared publication Hualong Lai
1 shared publication
Latest Publications
- 28 July 2025
- Published by Wiley in Steel Research International
- Vol. 97 (2) , 796-804
Effect of Bi Content on Microstructure, Mechanical Property, and Corrosion Behavior of Al–Zn–Mg–Cu–Sc–Zr Alloy
The effects of bismuth (Bi) content on the microstructure, mechanical, and corrosion behaviors of Al–Zn–Mg–Cu–Sc–Zr–Bi are systematically investigated. Al–Zn–Mg–Cu–Sc–Zr–Bi alloys with Bi content ranging from 0 to 0.5 wt% are synthesized via casting. The addition of Bi significantly refines the grain size from 52.6 to 23.2 nm, promoting the discontinuous precipitation of second phase particles along grain boundaries for Bi contents of 0.3–0.5 wt%. These Bi‐rich particles are identified through scanning electron microscopy/energy dispersive spectroscopy analysis. The tensile strength is substantially enhanced, with the synthesized alloy with 0.3 wt% of Bi achieving the highest 367.42 MPa. This improvement is attributed to lattice distortion caused by Bi dissolution and the Hall–Petch effect. However, excessive Bi content (>0.3 wt%) leads to stress concentration at grain boundaries, reducing tensile strength. Moreover, the synthesized alloy with 0.2 wt% of Bi exhibits the highest corrosion resistance, as indicated by electrochemical impedance spectroscopy results, which suggests improved capacitive characteristics due to Bi addition. This work highlights the potential of Bi as a microalloying element to optimize mechanical and corrosion properties of Al–Zn–Mg–Cu, offering a valuable insight for developing high‐performance structural materials with enhanced strength and corrosion resistance.
- 28 July 2025
- Published by Wiley in Steel Research International
- Vol. 97 (2) , 796-804
Effect of Bi Content on Microstructure, Mechanical Property, and Corrosion Behavior of Al–Zn–Mg–Cu–Sc–Zr Alloy
The effects of bismuth (Bi) content on the microstructure, mechanical, and corrosion behaviors of Al–Zn–Mg–Cu–Sc–Zr–Bi are systematically investigated. Al–Zn–Mg–Cu–Sc–Zr–Bi alloys with Bi content ranging from 0 to 0.5 wt% are synthesized via casting. The addition of Bi significantly refines the grain size from 52.6 to 23.2 nm, promoting the discontinuous precipitation of second phase particles along grain boundaries for Bi contents of 0.3–0.5 wt%. These Bi‐rich particles are identified through scanning electron microscopy/energy dispersive spectroscopy analysis. The tensile strength is substantially enhanced, with the synthesized alloy with 0.3 wt% of Bi achieving the highest 367.42 MPa. This improvement is attributed to lattice distortion caused by Bi dissolution and the Hall–Petch effect. However, excessive Bi content (>0.3 wt%) leads to stress concentration at grain boundaries, reducing tensile strength. Moreover, the synthesized alloy with 0.2 wt% of Bi exhibits the highest corrosion resistance, as indicated by electrochemical impedance spectroscopy results, which suggests improved capacitive characteristics due to Bi addition. This work highlights the potential of Bi as a microalloying element to optimize mechanical and corrosion properties of Al–Zn–Mg–Cu, offering a valuable insight for developing high‐performance structural materials with enhanced strength and corrosion resistance.
- 10 July 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (28) , 12122-12136
Effects of Sr and Sc combined alloying on the mechanical properties and corrosion behavior of Mg-6Zn-0.5Mn alloy
- 10 July 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (28) , 12122-12136
Effects of Sr and Sc combined alloying on the mechanical properties and corrosion behavior of Mg-6Zn-0.5Mn alloy
- 1 May 2021
- Published by Springer Nature in China Foundry
- Vol. 18 (3) , 223-228
Effect of Gd on microstructure and refinement performance of Al-5Ti-B alloy
- 1 May 2021
- Published by Springer Nature in China Foundry
- Vol. 18 (3) , 223-228
Effect of Gd on microstructure and refinement performance of Al-5Ti-B alloy
- Open Access
- 1 January 2017
- Published by Springer Nature in China Foundry
- Vol. 14 (1) , 22-27
Effect of high pressure on microstructure of cast Mg-8Zn-0.5Zr-0.5Gd alloy
- 1 January 2017
- Published by Springer Nature in China Foundry
- Vol. 14 (1) , 22-27
Open AccessEffect of high pressure on microstructure of cast Mg-8Zn-0.5Zr-0.5Gd alloy