Oliver Mertens
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Oliver Mertens has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Andreas Krause
University of Hamburg
2 shared publications- Andreas Krause
Thünen Institute of Wood Research, Leuschnerstraße 91c, 21031 Hamburg, Germany
2 shared publications Jan T. Benthien
Thünen Institute of Wood Research
1 shared publicationJulius Gurr
Department of Biology, Center of Wood Science and Technology, University Hamburg
1 shared publicationKim C. Krause
Department of Wood Biology and Wood Products, University of Goettingen, Göttingen, Germany
1 shared publication- Kim Christian Krause
Wood Biology and Wood Products, Faculty of Forest Sciences and Forest Ecology, University of Goettingen, Büsgenweg 4, 37077 Göttingen, Germany
1 shared publication
Latest Publications
- 23 July 2018
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 15 (2) , 114-122
Performance of thermomechanical wood fibers in polypropylene composites
Thermomechanical wood fibers, as usually used for medium density fiberboard or cardboard production, feature promising characteristics, like a high aspect ratio, for the utilization in thermoplastic composites. The present study investigates the influence of fiber loading and fiber geometry on the mechanical properties of wood-polypropylene composites in order to confirm the results that were found in a previously published literature review. Composites were compounded at fiber contents from 20 to 60 wt.%, using a co-rotating twin-screw extruder and subsequently injection molded to test specimens. Field emission scanning electron microscopy was carried out to evaluate the fracture morphology of the composites. Fiber length was evaluated using an applying a dynamic image analysis system. Compounding reduced fiber lengths up to 97%. The mechanical properties decreased with increasing fiber content for composites without a coupling agent. Strength properties peaking at a fiber content of 50 wt.% for composites containing MAPP. Tensile strength and flexural strength reached 48.1 and 76.4 MPa, respectively. However, it was found that the processing of these fibers into conventional compounding equipment is still challenging.
- 23 July 2018
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 15 (2) , 114-122
Performance of thermomechanical wood fibers in polypropylene composites
Thermomechanical wood fibers, as usually used for medium density fiberboard or cardboard production, feature promising characteristics, like a high aspect ratio, for the utilization in thermoplastic composites. The present study investigates the influence of fiber loading and fiber geometry on the mechanical properties of wood-polypropylene composites in order to confirm the results that were found in a previously published literature review. Composites were compounded at fiber contents from 20 to 60 wt.%, using a co-rotating twin-screw extruder and subsequently injection molded to test specimens. Field emission scanning electron microscopy was carried out to evaluate the fracture morphology of the composites. Fiber length was evaluated using an applying a dynamic image analysis system. Compounding reduced fiber lengths up to 97%. The mechanical properties decreased with increasing fiber content for composites without a coupling agent. Strength properties peaking at a fiber content of 50 wt.% for composites containing MAPP. Tensile strength and flexural strength reached 48.1 and 76.4 MPa, respectively. However, it was found that the processing of these fibers into conventional compounding equipment is still challenging.
- 23 October 2017
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 76 (2) , 801-804
Monitoring of fibre dimensions after a novel wood-plastic compounding approach
- 23 October 2017
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 76 (2) , 801-804
Monitoring of fibre dimensions after a novel wood-plastic compounding approach
- 23 October 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (7)
Evaluation of wood fiber composites based on a novel simultaneous defibration and compounding process
The distinctive length and morphology characteristics of thermomechanical produced wood fibers make it a promising candidate for the utilization in polymer composites. However, due to the low bulk density of these fibers, the feeding into the compounding process (i.e., extruders) is quite challenging. In this study, a novel simultaneous defibration and compounding process are conducted in order to solve the feed‐in problem of thermomechanical fibers. A disc‐refiner was used to defibrate wood chips to fibers and compound the fibers with neat polymer granulates in one process step. After the process, the material showed typically thermomechanical fibers with chopped polymer particles which were inseparably attached to the fiber. The observed mechanical properties of the composites were slightly lower than some literature values. With field emission scanning electron microscopy and X‐ray microtomography analysis, voids and a polymer enriched surface were found influencing the composites performance. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45859.
- 23 October 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (7)
Evaluation of wood fiber composites based on a novel simultaneous defibration and compounding process
The distinctive length and morphology characteristics of thermomechanical produced wood fibers make it a promising candidate for the utilization in polymer composites. However, due to the low bulk density of these fibers, the feeding into the compounding process (i.e., extruders) is quite challenging. In this study, a novel simultaneous defibration and compounding process are conducted in order to solve the feed‐in problem of thermomechanical fibers. A disc‐refiner was used to defibrate wood chips to fibers and compound the fibers with neat polymer granulates in one process step. After the process, the material showed typically thermomechanical fibers with chopped polymer particles which were inseparably attached to the fiber. The observed mechanical properties of the composites were slightly lower than some literature values. With field emission scanning electron microscopy and X‐ray microtomography analysis, voids and a polymer enriched surface were found influencing the composites performance. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45859.
- 13 April 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (31)
The utilization of thermomechanical pulp fibers in WPC: A review
Thermomechanical pulp (TMP), among other natural fibers, features characteristics that make it a promising candidate for the utilization in polymer composites. This review is providing an overview on the current state of research on TMP reinforced polymer composites. More than 50 references were reviewed. The cited literature is catalogued according to pretreatments, batch or continuous procedures, processing at laboratory or industrial scale, fiber contents, polymer types, coupling agents as well as wood species. The reinforcing potential of TMP utilized in composites is demonstrated. Tensile strength was found to be peaking at a fiber content of around 40 wt %. Fiber morphology is presumed to be an important determinator for composite properties. Specific mechanical energy [kWh/kg] is presented as an indicator suitable to compare the influence of various processes on fiber morphology. Furthermore, the feed‐in and dosing issue that generally accompanies the utilization of cellulosic fibers is described and possible solutions are discussed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45161.
- 13 April 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (31)
The utilization of thermomechanical pulp fibers in WPC: A review
Thermomechanical pulp (TMP), among other natural fibers, features characteristics that make it a promising candidate for the utilization in polymer composites. This review is providing an overview on the current state of research on TMP reinforced polymer composites. More than 50 references were reviewed. The cited literature is catalogued according to pretreatments, batch or continuous procedures, processing at laboratory or industrial scale, fiber contents, polymer types, coupling agents as well as wood species. The reinforcing potential of TMP utilized in composites is demonstrated. Tensile strength was found to be peaking at a fiber content of around 40 wt %. Fiber morphology is presumed to be an important determinator for composite properties. Specific mechanical energy [kWh/kg] is presented as an indicator suitable to compare the influence of various processes on fiber morphology. Furthermore, the feed‐in and dosing issue that generally accompanies the utilization of cellulosic fibers is described and possible solutions are discussed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45161.