Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kirill Vladimirovich Pikulin has a total of 54 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Evaluation of the possibility of aluminothermic processing of tantalum-niobium raw materials

    by K. V. Pikulin, S. N. Tyushnyakov, S. A. Fedorov, R. I. Gulyaeva, S. V. Sergeeva, L. Yu. Udoeva

    Under conditions of sustained growth in global demand for niobium and tantalum, the involvement of new deposits in processing and the development of efficient extraction technologies for these metals are becoming particularly relevant. Traditional hydrometallurgical schemes are well-established for rich concentrates; however, their application to low-grade raw materials and technogenic formations is associated with technological and economic challenges. A promising approach appears to be pyrometallurgical processing with recovery of valuable components into a metal concentrate (alloy) via aluminothermic reduction. This study examines the aluminothermic reduction of tantalum and niobium using natural columbite-tantalite (coltan) as an example – one of the principal ore minerals of industrial significance for tantalum-niobium raw materials. Results of a comprehensive investigation into the material composition of the sample and its influence on the efficiency of aluminothermic metal recovery are presented. It was established that niobium and tantalum in the studied coltan sample occur within the minerals columbite-tantalite and tapiolite, which differ in their crystal structures. Tin is present as cassiterite and partially as an isomorphic impurity in tantalite. Experimental results demonstrate that the interaction of coltan's mineral components with aluminum depends on their crystallochemical stability: the degree ofm etal recovery from columbite-tantalite is significantly higher than from tapiolite. The maximum extraction of Nb and Ta into the alloy without flux addition reached 93.0 % and 86.3 %, respectively; with the addition of calcium oxide for slag formation, these values decreased to 73.9 % and 85.3 % due to the formation of rare-metal calcium aluminates. In both cases, “benefication” of the reduction product (alloy) with target metals was observed, while the contents of accompanying components (Fe, Mn, Sn) remained virtually unchanged relative to the feed. Aluminothermic processing of tantalum-niobium raw materials can be considered an alternative pyrometallurgical benefication method, suitable for both standard-grade and low-grade rare-metal concentrates.

  • Phase formation features during metallothermic reduction of natural wolframite

    by K. V. Pikulin, L. I. Galkova, R. I. Gulyaeva, L. Yu. Udoeva, S. V. Sergeeva, S. N. Tyushnyakov

    The phase formation mechanisms during the metallothermic reduction of natural wolframite from the Akchatau Deposit using aluminum and a calcium-aluminum master alloy was investigated in this study. Thermodynamic simulation demonstrates that, regardless of the reducing agent employed (Al or Ca – Al master alloy), the equilibrium composition of the metallic phase consists of tungsten and ferrotungsten. The application of the Ca – Al master alloy increases the thermal effect of the process by 4.3% and raises the adiabatic temperature by 390 °C compared to the conventional aluminothermic route, while also enhancing the separation of the metallic and oxide phases due to the formation of low-melting calcium aluminates. Using differential scanning calorimetry (DSC), X-ray diffraction (XRD), and X-ray microanalysis (EPMA), it was established that both processes proceed in a stepwise manner; however, their underlying mechanisms differ fundamentally. In the aluminothermic process, the iron-bearing component of the mineral is reduced first, yielding aluminum-based intermetallic compounds, which subsequently react with the manganese-enriched residual wolframite fraction. When the Ca – Al master alloy is employed, the initial stage involves the formation of calcium tungstates (CaWO4, Ca3WO6, Ca2WMnO6) and aluminides of the principal metals; these intermediates, together with calcium vapor, subsequently reduce the complex oxides formed in the preceding step. It is shown that, in both cases, the final products of natural wolframite reduction are metallic tungsten and its solid solutions with iron and manganese. The results obtained may contribute to the optimization of out-of-furnace metallothermic processing technologies for tungstencontaining raw materials. The work was carried out according to the State Assignment for the Vatolin Institute of Metallurgy of the Ural Branch of the Russian Academy of Sciences (IMET UB RAS) using the equipment of the Collaborative Usage Center “Ural-M”.

  • Open Access

    Thermodynamic assessment of boron distribution and temperature characteristics during electric smelting separation of siderite concentrate with colemanite

    by Alexander Vusikhis, Kirill Pikulin, Stanislav Tyushnyakov, Kseniya Rybalchenko, Sergey Pikalov

    Siderite ores with high magnesium content are poorly amenable to conventional beneficiation, which limits their use in metallurgy. A promising processing method is electric smelting separation of metallized concentrate with calcined colemanite added as a flux to reduce the melting temperature of high‑magnesia slags. One issue is the potential reduction of boron from the slag into the metal. In this work, thermodynamic simulation in FactSage 7.0 is used to evaluate boron distribution between metal and slag. Calculations employ a four-factor experimental design according to the method of V.P. Malyshev. The variables include the SiO2/MgO ratio, the degree of metallization, the colemanite fraction, and the carbon content. Adding 10–15% colemanite reduces the slag liquidus temperature by 200–400 °C. Optimal regimes that ensure a slag liquidus temperature not exceeding 1450 °C and boron transfer to the slag above 95.3% are determined. At 95% metallization (SiO2/MgO = 1.5, colemanite 14.0%), boron transfer is 95.3–100% and the liquidus temperature is 1318–1406 °C. At 85% metallization, up to 2% carbon, SiO2/MgO of 1.4–1.5, and ~14.0% colemanite, boron‑free metal (B = 0.0%) is obtained. At 6% carbon, impurities increase (B up to 0.14%, Si up to 5.7%), yet the slag liquidus remains below 1447 °C. Reducing metallization to 75% yields boron‑free metal even at 6% carbon. These results provide a basis for developing an industrial technology for processing siderite ores by electric smelting separation.

  • Open Access

    Phase Formation Features in the Metallothermal Reduction of Natural Coltan

    by Kirill V. Pikulin, Stanislav N. Tyushnyakov, Roza I. Gulyaeva, Sofya A. Petrova, Andrey N. Dmitriev, Galina Yu. Vitkina

    Phase formation characteristics during the thermochemical reduction of metals from natural coltan using aluminum and calcium–aluminum alloy at 1400–1450 °C were investigated to develop methods for extracting niobium and tantalum from rare metal raw materials. The studied coltan sample consists of a columbite–tantalite solid solution with the composition (Mn,Fe)(Nb,Ta)2O6, cassiterite Sn0.9O2, tapiolite (Ta,Nb)2(Mn,Fe)O6, and calcioolivine Ca2SiO4. This study established that the choice of reducing agent determines the sequence of oxide phase transformations. During the aluminothermic process, orthorhombic columbite–tantalite is completely reduced, while tetragonal tapiolite persists even at 1400 °C. The use of a calcium–aluminum alloy containing 69.4 wt.% Ca results in a reversal of this trend: tapiolite is reduced at the early stages (800–1250 °C) through an intermediate (Ta,Nb)O2 phase, whereas the columbite–tantalite solid solution remains up to 1250 °C. Calcium, having a high affinity for oxygen, forms intermediate perovskite-type oxide phases that act as diffusion barriers, limiting the access of the reducing agent to residual mineral inclusions (mainly Nb-Ta minerals of the orthorhombic crystal system). A temperature rise to 1450 °C initiates the redistribution of oxide components: the content of CaNbO3 decreases, the Ca2(Nb,Ta)AlO6 phase disappears, and its components are involved in the formation of Ca(Nb,Ta)0.25MnO2.74 and Ca4Nb2O9. Diffusion constraints are reduced, and the residual columbite–tantalite solid solution is reduced, as confirmed by its complete absence in the products at 1450 °C. In the metallic phase, solid solutions of tantalum and niobium, Ta-Nb-Sn intermetallic compounds (Ta,Nb)3Sn, titanium aluminide, and ferroalloys with an increased (Ta,Nb)/(Fe,Mn) ratio are formed. The phase transformations elucidated during metallothermic reduction of coltan using different reducing agents, together with the formation of metallic and intermetallic phases, establish a scientific foundation for the development of advanced rare metal extraction processes.

  • Open Access

    Boron distribution between metal and slag during melting of metalized siderite concentrate in electric furnace

    by A. S. Vusikhis, S. N. Tyushnyakov, K. V. Pikulin, S. N. Agafonov, L. I. Leont’eV

    The Ural metallurgical enterprises compensate for the deficit of iron ore raw materials by supplying materials from Central Russia, the Kola Peninsula and Kazakhstan. Carbonate iron ores (siderites) of the Bakalskoye deposit are poor ores and, despite large reserves (about 1 billion tons), are not in great demand among metallurgists due to their low quality (low iron content and high magnesium content). The prospects for developing the Bakalskoye deposit depend on the availability of new technologies for processing siderites. There is a technology for processing poor iron ores using the coke-free metallurgy method, including reducing roasting in a rotary kiln, grinding and magnetic separation to obtain a highly metallized product suitable for steelmaking. Laboratory studies and industrial tests confirmed its suitability for processing siderites. A modernized technology for processing siderites is proposed, in which the operations of grinding and magnetic separation are excluded, and the product of reducing roasting in a rotary kiln is loaded hot into an electric furnace for separating melting. The process is carried out in the presence of colemanite containing boric anhydride to obtain liquid slag. During melting, part of the boron passes into the metal melt. By means of thermodynamic modeling, an assessment of the distribution of boron between the metal and slag as a result of separating melting is carried out. With a content of 5 and 10 % of colemanite in the charge, depending on the proportion of carbon, up to 60 % of boron passes into the metal. Such metal can be used as a ligature for obtaining boron-containing steel or cast iron. When bubbling the metal melt with oxygen, boron content can be reduced to 0.0001 %.

  • Kinetics and Mechanism of Wolframite Concentrate Interaction with Potassium Carbonate during Sintering

    by K.V. Pikulin, L.I. Galkova, R.I. Gulyaeva, A.A. Karapuzikova, E.A. Nifontova

    The kinetics and mechanism of interaction of wolframite concentrate with potassium carbonate during sintering in the temperature range of 25–1000 °C were studied. The sequence of phase transformations in an oxidizing atmosphere of air was established using thermal, X-ray spectral and X-ray phase analyses, as well as gas mass spectrometry. It was shown that in the temperature range of 520–820 °C, water-soluble potassium tungstate, its eutectic mixture with the initial reagent, and ferrite phases, iron and manganese oxides with a variable oxidation state are formed. A change in the wolframite composition during sintering was revealed, accompanied by a decrease in the proportion of iron, which is confirmed by an increase in the unit cell parameters of the FeMnWO phase. The kinetics of the process is described by a single-stage model with a dominant effect of autocatalytic nucleation, the activation energy is 56.6–56.9 kJ/mol. The obtained results are important for the development of technologies for processing wolframite concentrates to obtain soluble compounds.

  • Effect of Mechanical Activation on the Thermal Oxidation of Sphalerite

    by R. I. Gulyaeva, K. V. Pikulin, S. Kh. Estemirova, S. V. Sergeeva

    We consider the effect of mechanical activation on the particle size and strain of natural sphalerite particles and demonstrate that mechanical activation of the mineral for 20 min in a high-energy planetary mill reduces the crystallite size to 20 nm and that in this process the lattice strain in sphalerite reaches 0.73–0.85%. Thermogravimetry, calorimetry, and mass spectrometry have been used to study sphalerite oxidation processes during nonisothermal heating to a temperature of 1000°C in flowing air before and after mechanical activation. Mechanical activation of sphalerite has been shown to lead to a slight increase in the rate of sulfate formation, a decrease in the temperature and enthalpy of the thermal effects involved, and release of sulfur dioxide as a product of interaction with oxygen starting at a temperature of 150°C.


  • Open Access

    Technological Aspects of Sintering Low-Quality Wolframite Concentrate with Potassium Carbonate

    by Kirill V. Pikulin, Lyudmila I. Galkova, Galina Y. Vitkina, Antonina I. Karlina

    The loss of quality of wolframite concentrates determines the need to improve their processing method that ensures maximum conversion of tungsten into water-soluble wolframate and a reduction in water-soluble impurities. The results of thermodynamic modeling of the sintering of wolframite concentrate with sodium and potassium carbonates indicate a greater efficiency of K2CO3: The reagent consumption required for complete conversion of tungsten into solution decreases from 170% from stoichiometric sintering with Na2CO3 to 110% for K2CO3, as well as the proportion of soluble silicates up to 0.1%. In addition, sintering with K2CO3 is accompanied by the formation of compounds with a higher melting point, preventing melting and coating formation during the process. Mathematical sintering models were obtained by the method of probabilistically deterministic planning of this experiment. Optimal parameters have been determined: The extraction of tungsten into a solution of more than 95% is achieved by sintering with K2CO3 in an amount of 105–110% according to the stoichiometric requirements for the formation of K2WO4, K2MoO4, and K2SO4 at temperatures of 1073–1123 K for 100–120 min. Pilot tests have confirmed the effectiveness of the process. The possibility of sintering a cinder of wolframite concentrate with K2CO3 without the introduction of recycled materials has been established. Sintering under optimal conditions ensures the transition of tungsten to water-soluble tungstate by 97.5%.

  • Open Access

    Joint processing of perovskite and ilmenite concentrates. Part 1. Chemical-mineralogical (material) characteristics of perovskite and ilmenite concentrates

    by S. A. Fedorov, L. Yu. Udoeva, A. S. Vusikhis, K. V. Pikulin, L. A. Cherepanova

    Russia has an impressive titanium mineral resource while the contribution into the global production of titanium concentrates is quite insignificant. The current annual demand of Russian enterprises for titanium raw materials is 40 times higher than its production. To improve and launch the processing of domestic titanium raw materials characterized by low quality and complex polymineral composition, new process solutions are required. These solutions should aim at the full extraction of TiO2 and related valuable components from the ore deposits whose development is planned or already started (for example, Afrikanda – perovskite-titanomagnetite deposit located on the Kola Peninsula). This report presents the results of studying the chemical and mineral compositions of perovskite and ilmenite concentrates with the purpose to assess the possibility of their joint processing using carbothermic reduction melting. Emission spectrometry, X-ray diffraction, electron microscopy, and X-ray spectral microanalysis were applied in these studies. It was found that the basis of the ilmenite gravity concentrate sample is modified ilmenite represented by leucoxenization products – pseudorutile and rutile, with their total content in the concentrate to be about 80 wt. %. Composition of other minerals (alumochromite, chromite, magnetite) includes titanium in the form of impurities – 2 – 3 wt. %. In the perovskite flotation concentrate sample titanium is contained in perovskite and titanite making up the bulk of the ore minerals of the concentrate. As for rare and rare-earth elements contained in the ilmenite sample – monazite having up to 33 wt. % Ce, and zircon were found. Perovskite sample contains rare-earth elements (REE concentration in wt. %) in loparite-(Ce) (22.8), aluminocerite-(Ce) (46.2), anсylite-(Ce) (51.3), torite (22.3), as well as in the main mineral – perovskite (2.8). With the exception of perovskite and loparite-(Ce), other REE-containing minerals are rare, and their share in total does not exceed 1 wt. %


  • Results on Testing New Process to Make Nitrogen- and Carbon-Containing Precursor Based on Vanadium and Aluminum to Smelt V–Al–N–C Master Alloy

    by A. V. Larionov, D. V. Taranov, A. N. Rylov, M. V. Trubachev, S. A. Vohmentsev, M. H. Ziatdinov, I. R. Manashev, K. V. Pikulin

    A new process to make complex nitrogen- and carbon-containing precursor materials V(51–43)–Al(30–36)–N(13.4–16.4)–C(2.7–6.0) is developed involving nitriding mixtures of powder of industrial alloys V(65–50)–Al with graphite using self-propagating high-temperature synthesis. The results of pilot tests are encouraging. The ratio of nitrogen to carbon can vary in precursors over a wide range: N/C = 5.5–2.2. X‑ray diffraction analysis confirms that in these materials nitrogen has the form of AlN and VN nitrides, and carbon has the form of double V2C and VC and triple V2Al0.96C1.1 carbides. It is proved experimentally that graphite can be replaced by alternative precursor V(51)–Al(30)–N(15)–C(2.7) in the charge of ladle aluminothermic smelting master alloy V–Al–N–C. The comparison is made between phase composition and distribution of nitride and carbide inclusions in master alloy V–Al–N–C ingots and in those of master alloys smelted using other carbon-containing materials. The comparison involves X-ray diffraction analysis, electron microscopy, and X-ray spectral microanalysis. Matching results are obtained. The nitrogen, carbon, and oxygen content in the ingot meets the requirements set forth in the technical specifications for the master alloys of grade V–Al–N–C.