Jianhua Fan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jianhua Fan has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Franck Lominé
INSA, LGCGM, EA3913, F-35708, Rennes, France
2 shared publications - Lu Wang
Jilin University
2 shared publications Bo Li
1 shared publication- Chengzhi Zhu1 shared publication
Daizhe Yang
1 shared publication- Hongwei Wang1 shared publication
Latest Publications
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Aerodynamic noise optimization of a voluteless centrifugal fan with biomimetic blades inspired by eagle-owl wingtip morphology
Inspired by the low-noise characteristics of the eagle-owl nocturnal flight, two novel designs for blades of the voluteless centrifugal fan are proposed to improve the aerodynamic performance and reduce the noise. A serrated structure inspired by the eagle-owl wingtips at the trailing edge is adopted to design and optimize the blade. Based on the computational fluid dynamics methods and the Ffowcs Williams–Hawkings equation, the impact of the serrated leading and trailing edges on the aerodynamic performance and acoustic characteristics of a fan is investigated. The optimal geometric parameters of the bionic sawtooth are determined. Subsequently, a comprehensive comparison of the flow characteristics and noise spectra among the fan with the original blade (OBLE), the serrated leading-edge blade (SLBE), and the serrated trailing-edge blade (STBE) is conducted, revealing the control mechanism of the SLBE and STBE on the flow properties and noise optimization principles. Results demonstrate that the SLBE fan not only mitigates pressure fluctuations and optimizes vortices but also increases the maximum flow rate by 1.76%. Although the STBE fan also optimizes pressure and vortices, its efficiency slightly decreases due to reduced blade lift. However, the STBE fan achieves outstanding noise suppression, reducing the sound pressure level (SPL) by 6.42 dB compared to the OBLE fan. While the SLBE fan yields a limited SPL reduction of only 1.97 dB. Additionally, the noise energy shift at 1364 Hz demonstrates frequency modulation caused by the serrations. The blade trailing edge is identified as the primary noise source, and the STBE fan significantly attenuates broadband and tonal noise by optimizing the airflow disturbance suppression at the impeller outlet. These findings validate the feasibility of using biomimetic serrated designs to optimize the performance of voluteless centrifugal fans.
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Aerodynamic noise optimization of a voluteless centrifugal fan with biomimetic blades inspired by eagle-owl wingtip morphology
Inspired by the low-noise characteristics of the eagle-owl nocturnal flight, two novel designs for blades of the voluteless centrifugal fan are proposed to improve the aerodynamic performance and reduce the noise. A serrated structure inspired by the eagle-owl wingtips at the trailing edge is adopted to design and optimize the blade. Based on the computational fluid dynamics methods and the Ffowcs Williams–Hawkings equation, the impact of the serrated leading and trailing edges on the aerodynamic performance and acoustic characteristics of a fan is investigated. The optimal geometric parameters of the bionic sawtooth are determined. Subsequently, a comprehensive comparison of the flow characteristics and noise spectra among the fan with the original blade (OBLE), the serrated leading-edge blade (SLBE), and the serrated trailing-edge blade (STBE) is conducted, revealing the control mechanism of the SLBE and STBE on the flow properties and noise optimization principles. Results demonstrate that the SLBE fan not only mitigates pressure fluctuations and optimizes vortices but also increases the maximum flow rate by 1.76%. Although the STBE fan also optimizes pressure and vortices, its efficiency slightly decreases due to reduced blade lift. However, the STBE fan achieves outstanding noise suppression, reducing the sound pressure level (SPL) by 6.42 dB compared to the OBLE fan. While the SLBE fan yields a limited SPL reduction of only 1.97 dB. Additionally, the noise energy shift at 1364 Hz demonstrates frequency modulation caused by the serrations. The blade trailing edge is identified as the primary noise source, and the STBE fan significantly attenuates broadband and tonal noise by optimizing the airflow disturbance suppression at the impeller outlet. These findings validate the feasibility of using biomimetic serrated designs to optimize the performance of voluteless centrifugal fans.
- Open Access
- 1 December 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (12)
Flow rate characterization for liquid-immersed granular medium discharging through a hopper
The granular sample immersed in a viscous fluid discharge through an orifice connecting a pipe or no pipe has been numerically investigated. A two-dimensional fluid–particle model is adapted, which combines the discrete element method with the lattice Boltzmann method using the partial saturation boundary technique. The discharge rate of liquid-immersed granular media flowing from a hopper is parametrically analyzed by adding a pipe at the outlet, varying fluid properties and orifice sizes. The results show that the existence of the pipe significantly slows down the discharge rate compared with the no-pipe case. A revisited law based on the experimental investigations is proposed by incorporating particle maximum velocity, enabling the prediction of the discharge rate properly. To account for the fluid–particle interaction, the velocity distribution of the particle and its surrounding fluid is analyzed at the local scale. Then, an extension of the kinematic model linking the particle flow rate and velocity distribution is proposed, which allows the prediction of granular discharge from a hopper by considering the influence of the interstitial fluid.
- 1 December 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (12)
Open AccessFlow rate characterization for liquid-immersed granular medium discharging through a hopper
The granular sample immersed in a viscous fluid discharge through an orifice connecting a pipe or no pipe has been numerically investigated. A two-dimensional fluid–particle model is adapted, which combines the discrete element method with the lattice Boltzmann method using the partial saturation boundary technique. The discharge rate of liquid-immersed granular media flowing from a hopper is parametrically analyzed by adding a pipe at the outlet, varying fluid properties and orifice sizes. The results show that the existence of the pipe significantly slows down the discharge rate compared with the no-pipe case. A revisited law based on the experimental investigations is proposed by incorporating particle maximum velocity, enabling the prediction of the discharge rate properly. To account for the fluid–particle interaction, the velocity distribution of the particle and its surrounding fluid is analyzed at the local scale. Then, an extension of the kinematic model linking the particle flow rate and velocity distribution is proposed, which allows the prediction of granular discharge from a hopper by considering the influence of the interstitial fluid.
- 22 March 2018
- Published by Springer Nature in Acta Mechanica
- Vol. 229 (7) , 2843-2860
A numerical analysis of pressure drop and particle capture efficiency by rectangular fibers using LB-DE methods
- 22 March 2018
- Published by Springer Nature in Acta Mechanica
- Vol. 229 (7) , 2843-2860
A numerical analysis of pressure drop and particle capture efficiency by rectangular fibers using LB-DE methods
- Open Access
- 30 June 2017
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 140, 03003
Numerical study of particle capture efficiency in fibrous filter
EPJ Web of Conferences, open-access proceedings in physics and astronomy
- 30 June 2017
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 140, 03003
Open AccessNumerical study of particle capture efficiency in fibrous filter
EPJ Web of Conferences, open-access proceedings in physics and astronomy