Ivan Taritaš
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ivan Taritaš has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Darko Kozarac
University of Zagreb
3 shared publications - Mario Sremec
Department of Internal Combustion Engines and Mechanical Handling Equipment, Faculty of Mechanical Engineering and Naval Architecture, Zagreb, Croatia
2 shared publications - Momir Sjerić
University of Zagreb
2 shared publications - Mislav Blažić
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Zagreb, Croatia
1 shared publication - Zoran Lulić
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Ivana Lucica 5, HR-10000 Zagreb, Croatia
1 shared publication
Latest Publications
- 1 December 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Energy Engineering
- Vol. 143 (6)
Effect of Spark Plug Geometry on the Cyclic Combustion Variability and Fuel Consumption of Gasoline Engines
A numerical analysis of the effect of spark plug geometry on the cyclic combustion variability and fuel consumption is presented. Cycle simulations are performed at different operating conditions of a spark-ignition engine including changes of engine speed and load. After calibration of the model constants for an average cycle using the experimental results of the considered engine, the cyclic combustion variability over 1,500 cycles with the application of a classic J-gap spark plug is simulated. With the same values of calibration constants and perturbations of parameters that cause the cyclic combustion variability, cycle simulations are performed with a fine central (iridium) electrode spark plug. The cycle simulation results for the evaluation of combustion stability and fuel consumption are compared with the previous simulation results achieved with the classic spark plug geometry. The application of the iridium spark plug electrode improves the combustion stability over the analyzed operating range of the engine, with a maximum improvement of 13.5% at part load and low engine speed. A reduction of fuel consumption of approximately 1.25% is achieved at part load conditions. The simulation results confirm that the application of the iridium spark plug geometry has potential to improve engine stability and fuel economy.
- 1 December 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Energy Engineering
- Vol. 143 (6)
Effect of Spark Plug Geometry on the Cyclic Combustion Variability and Fuel Consumption of Gasoline Engines
A numerical analysis of the effect of spark plug geometry on the cyclic combustion variability and fuel consumption is presented. Cycle simulations are performed at different operating conditions of a spark-ignition engine including changes of engine speed and load. After calibration of the model constants for an average cycle using the experimental results of the considered engine, the cyclic combustion variability over 1,500 cycles with the application of a classic J-gap spark plug is simulated. With the same values of calibration constants and perturbations of parameters that cause the cyclic combustion variability, cycle simulations are performed with a fine central (iridium) electrode spark plug. The cycle simulation results for the evaluation of combustion stability and fuel consumption are compared with the previous simulation results achieved with the classic spark plug geometry. The application of the iridium spark plug electrode improves the combustion stability over the analyzed operating range of the engine, with a maximum improvement of 13.5% at part load and low engine speed. A reduction of fuel consumption of approximately 1.25% is achieved at part load conditions. The simulation results confirm that the application of the iridium spark plug geometry has potential to improve engine stability and fuel economy.
- Open Access
- 1 December 2017
- Published by SDEWES Centre in Journal of Sustainable Development of Energy, Water and Environment Systems
- Vol. 5 (4) , 518-532
Numerical Investigation of Injection Timing Influence on Fuel Slip and Influence of Compression Ratio on Knock Occurrence in Conventional Dual Fuel Engine
Compressed natural gas can be used in diesel engine with great benefits, but because of its low reactivity it is usually used in a so called dual fuel combustion process. Optimal parameters for dual fuel engines are not yet investigated thoroughly which is the motivation for this work. In this work, a numerical study performed in a cycle simulation tool (AVL Boost v2013) on the influence of different injection timings on fuel slip into exhaust and influence of compression ratio on knock phenomena in port injected dual fuel engine was conducted. The introduction of natural gas into the intake port of a diesel engine usually results in some fuel slipping into the exhaust port due to valve overlap. By analysing the simulation results, the injection strategy that significantly decreases the natural gas slip is defined. The knock occurrence study showed that the highest allowed compression ratio that will result in knock free operation of the presented engine is 18 for ambient intake condition, while for charged intake conditions the compression ratio should be lowered to 16.
- 1 December 2017
- Published by SDEWES Centre in Journal of Sustainable Development of Energy, Water and Environment Systems
- Vol. 5 (4) , 518-532
Open AccessNumerical Investigation of Injection Timing Influence on Fuel Slip and Influence of Compression Ratio on Knock Occurrence in Conventional Dual Fuel Engine
Compressed natural gas can be used in diesel engine with great benefits, but because of its low reactivity it is usually used in a so called dual fuel combustion process. Optimal parameters for dual fuel engines are not yet investigated thoroughly which is the motivation for this work. In this work, a numerical study performed in a cycle simulation tool (AVL Boost v2013) on the influence of different injection timings on fuel slip into exhaust and influence of compression ratio on knock phenomena in port injected dual fuel engine was conducted. The introduction of natural gas into the intake port of a diesel engine usually results in some fuel slipping into the exhaust port due to valve overlap. By analysing the simulation results, the injection strategy that significantly decreases the natural gas slip is defined. The knock occurrence study showed that the highest allowed compression ratio that will result in knock free operation of the presented engine is 18 for ambient intake condition, while for charged intake conditions the compression ratio should be lowered to 16.
- Open Access
- 26 April 2017
- Published by Faculty of Mechanical Engineering and Naval Architecture, Univ. of Zagreb in Transactions of FAMENA
- Vol. 41 (1) , 1-14
The Effect of Operating Parameters on Dual Fuel Engine Performance and Emissions – An Overview
In order to decrease harmful exhaust gas emissions from internal combustion engines, researchers are continuously looking for alternative fuels and combustion techniques, and in this context the use of natural gas as a supplement for...
- 26 April 2017
- Published by Faculty of Mechanical Engineering and Naval Architecture, Univ. of Zagreb in Transactions of FAMENA
- Vol. 41 (1) , 1-14
Open AccessThe Effect of Operating Parameters on Dual Fuel Engine Performance and Emissions – An Overview
In order to decrease harmful exhaust gas emissions from internal combustion engines, researchers are continuously looking for alternative fuels and combustion techniques, and in this context the use of natural gas as a supplement for...