DKDarko Kozarac

Darko Kozarac

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Darko Kozarac has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Study of Air and EGR Dilution in a Pre-Chamber Spark-Ignited Engine Fueled by Methane

    by Viktor Dilber, Sara Ugrinić, Rudolf Tomić, Darko Kozarac

    Improving the efficiency of spark-ignited (SI) engines while simultaneously reducing emissions remains a critical challenge in meeting global energy demands and increasingly stringent environmental regulations. Lean burn combustion is a proven strategy for increasing efficiency in SI engines. However, the air dilution level is limited by the mixture’s ignition ability and poor combustion efficiency and stability. A promising method to extend the dilution limit and ensure stable combustion is the implementation of an active pre-chamber combustion system. The pre-chamber spark-ignited (PCSI) engine facilitates stable and rapid combustion of very lean mixtures in the main chamber by utilizing high ignition energy from multiple flame jets penetrating from the pre-chamber (PC) to the main chamber (MC). Together with the increase in efficiency by dilution of the mixture, nitrogen oxide (NOX) emissions are lowered. However, at peak efficiencies, the NOX emissions are still too high and require aftertreatment. The use of exhaust gas recirculation (EGR) as a dilutant might enable simple aftertreatment by using a three-way catalyst. This study experimentally investigates the use of EGR as a dilution method in a PCSI engine fueled by methane and analyzes the benefits and drawbacks compared to the use of air as a dilution method. The experimental results are categorized into three sets: measurements at wide open throttle (WOT) conditions, at a constant engine load of indicated mean effective pressure (IMEP) of 5 bar, and at IMEP = 7 bar, all at a fixed engine speed of 1600 rpm. The experimental results were further enhanced with numerical 1D/0D simulations to obtain parameters such as the residual combustion products and excess air ratio in the pre-chamber, which could not be directly measured during the experimental testing. The findings indicate that air dilution achieves higher indicated efficiency than EGR, at all operating conditions. However, EGR shows an increasing trend in indicated efficiency with the increase in EGR rates but is limited due to misfires. In both dilution approaches, at peak efficiencies, aftertreatment is required for exhaust gases because they are above the legal limit, but a significant decrease in NOX emissions can be observed.

  • Open Access

    Developing a Spatial Emission Inventory of Agricultural Machinery in Croatia by Using Large-Scale Survey Data

    by Šimun Lončarević, Petar Ilinčić, Zoran Lulić, Darko Kozarac

    Agricultural machinery has an essential impact on climate change. However, its emission data are often missing, which makes it harder to develop policies which could lower its emissions. An emission inventory should first be developed to understand the impact of agricultural machinery on climate change. This article presents a spatial variation of emissions from agricultural machinery in Croatia. Data on agricultural machinery for 2016 was collected via a large-scale survey with 8895 respondents and included machinery type, location data, and fuel consumption by fuel type. Data processing was conducted to optimize the survey results, and the emissions were calculated using the “EEA/EMEP Emission Inventory Guidebook” Tier 1 method. The research shows that two-axle tractors with engine power 61–100 kW had the most significant energy consumption and were responsible for most of the emissions. The highest total emissions were in counties in the Slavonia region, while counties in the Dalmatia region had the highest emissions per hectare of arable land. Results obtained this way enable policies to be developed that will target specific spatial areas and machinery types. Furthermore, this approach could allow precise spatial and temporal emission tracking. A designated institution which could conduct annual surveys and update the agricultural machinery emission data would ensure emission data continuity.


  • Open Access

    Optimization of Pre-Chamber Geometry and Operating Parameters in a Turbulent Jet Ignition Engine

    by Viktor Dilber, Momir Sjerić, Rudolf Tomić, Josip Krajnović, Sara Ugrinić, Darko Kozarac

    A turbulent jet ignition engine enables operation with lean mixtures, decreasing nitrogen oxide (NOX) emissions up to 92%, while the engine efficiency can be increased compared to conventional spark-ignition engines. The geometry of the pre-chamber and engine operating parameters play the most important role in the performance of turbulent jet ignition engines and, therefore, must be optimized. The initial experimental and 3D CFD results of a single-cylinder engine fueled by gasoline were used for the calibration of a 0D/1D simulation model. The 0D/1D simulation model was upgraded to capture the effects of multiple flame propagations, and the evolution of the turbulence level was described by the new K-k-ε turbulence model, which considers the strong turbulent jets occurring in the main chamber. The optimization of the pre-chamber volume, the orifice diameter, the injected fuel mass in the pre-chamber and the spark timing was made over 9 different operating points covering the variation in engine speed and load with the objective of minimizing the fuel consumption while avoiding knock. Two optimization methods using 0D/1D simulations were presented: an individual optimization method for each operating point and a simultaneous optimization method over 9 operating points. It was found that the optimal pre-chamber volume at each operating point was around 5% of the clearance volume, while the favorable orifice diameters depended on engine load, with optimal values around 2.5 mm and 1.2 mm at stoichiometric mixtures and lean mixtures, respectively. Simultaneous optimization of the pre-chamber geometry for all considered operating points resulted in a pre-chamber volume equal to 5.14% of the clearance volume and an orifice diameter of 1.1 mm.


  • Open Access

    Experimental study on knock sources in spark ignition engine with exhaust gas recirculation

    by Mladen Božić, Ante Vučetić, Momir Sjerić, Darko Kozarac, Zoran Lulić


  • Effect of Spark Plug Geometry on the Cyclic Combustion Variability and Fuel Consumption of Gasoline Engines

    by Momir Sjerić, Ivan Taritaš, Darko Kozarac

    A numerical analysis of the effect of spark plug geometry on the cyclic combustion variability and fuel consumption is presented. Cycle simulations are performed at different operating conditions of a spark-ignition engine including changes of engine speed and load. After calibration of the model constants for an average cycle using the experimental results of the considered engine, the cyclic combustion variability over 1,500 cycles with the application of a classic J-gap spark plug is simulated. With the same values of calibration constants and perturbations of parameters that cause the cyclic combustion variability, cycle simulations are performed with a fine central (iridium) electrode spark plug. The cycle simulation results for the evaluation of combustion stability and fuel consumption are compared with the previous simulation results achieved with the classic spark plug geometry. The application of the iridium spark plug electrode improves the combustion stability over the analyzed operating range of the engine, with a maximum improvement of 13.5% at part load and low engine speed. A reduction of fuel consumption of approximately 1.25% is achieved at part load conditions. The simulation results confirm that the application of the iridium spark plug geometry has potential to improve engine stability and fuel economy.


  • Open Access

    Numerical Investigation of Injection Timing Influence on Fuel Slip and Influence of Compression Ratio on Knock Occurrence in Conventional Dual Fuel Engine

    by Mario Sremec, Ivan Taritaš, Momir Sjerić, Darko Kozarac

    Compressed natural gas can be used in diesel engine with great benefits, but because of its low reactivity it is usually used in a so called dual fuel combustion process. Optimal parameters for dual fuel engines are not yet investigated thoroughly which is the motivation for this work. In this work, a numerical study performed in a cycle simulation tool (AVL Boost v2013) on the influence of different injection timings on fuel slip into exhaust and influence of compression ratio on knock phenomena in port injected dual fuel engine was conducted. The introduction of natural gas into the intake port of a diesel engine usually results in some fuel slipping into the exhaust port due to valve overlap. By analysing the simulation results, the injection strategy that significantly decreases the natural gas slip is defined. The knock occurrence study showed that the highest allowed compression ratio that will result in knock free operation of the presented engine is 18 for ambient intake condition, while for charged intake conditions the compression ratio should be lowered to 16.