DKDietmar Kracht

Dietmar Kracht

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dietmar Kracht has a total of 99 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Spherical aberration compensation in Nd:YVO 4 amplifiers

    by Merle Schneewind, Stefan Spiekermann, Peter Wessels, Joerg Neumann, Dietmar Kracht

    The thermally induced spherical aberration in an 878.6 nm pumped Nd:YVO 4 laser amplifier was compensated using a custom-designed optical plate shaped according to the Zernike polynomial for spherical aberration. Wavefront measurements performed with a Shack-Hartmann sensor were applied to a 976 nm probe beam, unaffected by amplification, and the 1064 nm signal beam. Identical wavefront distortions and an effective compensation by the compensation plates were observed in both cases, confirming that the aberration originates solely from thermal lensing. This validates the probe beam as a reliable diagnostic tool and demonstrates the effectiveness of the compensation plate in restoring wavefront quality.

  • Up-chirped nonlinear thulium fiber amplifier delivering sub-100 fs high-energetic pulses

    by Benedikt Schuhbauer, Joe Pius, Alessandro Favia, Frithjof Haxsen, Uwe Morgner, Joerg Neumann, Dietmar Kracht

    Nonlinear fiber amplifiers allow for scaling the pulse energy, while the pulse properties can be tailored by the interplay of dispersion and Kerr-nonlinearity, aiming to significantly shorten the input pulses. Here, we describe a monolithic polarization-maintaining nonlinear fiber amplifier based on thulium, relying solely on single-mode step-index fused silica fibers. During the amplification of up-chirped pulses with an initial transform-limited pulse duration of 2.3 ps in an anomalous dispersive gain fiber, monotonic spectral broadening occurs and is subsequently extended in a normal dispersive fiber. The setup generates pulses with ultra-broadband spectra of up to 119 nm at pulse energies of up to 74 nJ. The pulses can be well compressed to sub-100 fs duration, equivalent to a compression factor of 24. Even though massive nonlinear spectral broadening is observed, the noise performance characterized by the relative intensity noise remains almost unaffected. Fundamentals for design and limitations of the output parameters are discussed by a numerical model.


  • Laser-machined, kilowatt-class cladding light strippers with stripping efficiencies > 37 dB

    by Nils Haverland, Finn Salhoff, Fabian Kranert, Joerg Neumann, Dietmar Kracht

    Cladding light strippers are a crucial component for fiber-based laser and amplifier systems, stripping unabsorbed pump light behind the active fiber. Laser-machining presents an effective alternative to chemical etching in the production of high-power cladding light strippers. Here, we present improvements to laser-machined, microstructured cladding light strippers, which achieve cladding light attenuation up to 37.3 dB on a length of just 60 mm. We tested the high-power stripping capability of a cladding light stripper, achieving a stripped cladding light power of 1.2 kW. The result was limited by the available power. The cladding light strippers were designed by utilizing raytracing simulations to optimize the microstructure on the fiber towards homogenized stripping and increased cladding light attenuation. Afterwards, the most promising results were transferred to manufacturing and characterized. The availability of high-power, high attenuation microstructured cladding light strippers can help to improve future laser systems, possibly foregoing the need for chemical etching.

  • Open Access

    Side-fused signal–pump combiner and microstructured cladding light stripper for triple-clad fibers

    by Eike Brockmüller, Nils Haverland, Daniil Antonov, Dominic Zentgraf, Fabian Kranert, Roland Lachmayer, Jörg Neumann, Dietmar Kracht

    Triple-clad fibers are, in particular, used in thulium- and holmium-doped fiber lasers and amplifiers to increase the threshold for critical fiber damage, e.g., caused by absorption in the coating. This would allow for further power scaling. However, essential fiber-based components such as side-fused signal–pump combiners and cladding light strippers are not available for this fiber type. As the fiber design prevents the required access to the inner pump cladding, it hinders efficient component manufacturing. Here, we present manufacturing processes involving CO2 laser-based ablation that enable the production of these components. For the manufactured signal–pump combiner with a 14/400/480-μm triple-clad fiber and up to four 135/155-μm pump input fibers, a pump coupling efficiency of 95.5%, a signal loss of 0.2 dB, and a signal-to-pump isolation of 34 dB were achieved. We confirm by ray tracing simulation that most of the pump power is coupled into the inner cladding of the triple-clad fiber. The cladding light stripper, manufactured out of the same fiber sample, achieved a cladding light attenuation of 20.8 dB, whereas no significant signal loss was detected. The availability of these components enables monolithic laser and amplifier setups with triple-clad fibers and supports their power scaling with high beam quality.

  • Experimental and numerical analysis of thermal lensing effects in Nd:YVO 4

    by Merle Schneewind, Phillip Booker, Sergii Iakushev, Stefan Spiekermann, Peter Wessels, Joerg Neumann, Dietmar Kracht

    The power dependent wavefront distortions in a Nd:YVO 4 laser amplifier were analyzed using a 976 nm probe beam. The experimental results were in excellent agreement with a numerical thermo-optical model based on split-step Fourier propagation. Although direct pumping at 878.6 nm was used, the quantum defect was identified as the dominant heat source (99 % of total heat) while energy transfer upconversion and fluorescence quenching have only a local contribution. As a result, the thermal lens reached 14 dpt dioptric power at 43 W output power (46 % efficiency). Apart from the defocus, astigmatism and spherical aberrations were identified as main components of the thermal lens.


  • Gain dynamics in thulium-doped fiber amplifiers

    by Benedikt Schuhbauer, Frithjof Haxsen, Uwe Morgner, Joerg Neumann, Dietmar Kracht

    Understanding the gain dynamics of amplification in rare-earth-doped silica glass fibers is crucial for developing sophisticated low-noise amplifiers and frequency combs. Recent and ongoing research efforts in these areas have specifically targeted the spectral region around 2 µm and the use of thulium-doped silica glass fibers as a broadband, power-scalable gain medium. We present a comprehensive characterization of the transfer functions of thulium ions in silica glass for emission in the spectral 2 µm region, including the magnitude and phase information. We investigated the most widespread pumping schemes: in-band pumping at 1550 nm, as well as out-of-band pumping at 790 nm. A semi-analytical model and a numerical model are developed to describe the complex energy level system of thulium ions and their associated ion-ion interactions, providing deeper insight into the influence of various parameters on the transfer functions of thulium ions in silica glass. The presented results of the transfer functions support the choice of fiber amplifier geometries and electronics to optimize noise performance.


  • Reduction of thermally induced waveguide degradation in the laser glass deposition of optical fibers through melt pool adaption

    by Florian Spengler, Sven-Olaf Waldhauer, Saikat Chandra Das, Anna Karoline Rüßeler, Stefan Kaierle, Dietmar Kracht, Moritz Hinkelmann

    With the laser glass deposition, optical quartz glass fibers with a core-cladding structure are welded on fused silica chips for all-glass on-chip light-guiding systems. However, previous welding experiments resulted in a degradation of the transmission properties of the fibers [F. Spengler, Procedia CRIP, 124, 484 (2024)]. In this work, the beam path of the CO2 laser is modified to improve the transmission of the on-chip welded fibers and to maintain their single-mode properties. Rather than being guided directly onto the fiber from above, the laser beam is directed between the fiber and the substrate. The fiber is continuously placed in the created melt pool of the substrate, which enables a material bond with reduced thermal impact on the fiber core. The influence of process parameters, such as the power density and the wavefront curvature, on the optical transmission properties of welded fibers is systematically analyzed. Compared to previous processes, a 50% reduction in optical transmission losses can be observed. In the same process environment, an innovative laser-based cleaving process is being developed to create cleaves with end facet angles between 0° and 12°, enabling efficient and versatile coupling strategies and precise on-chip integration of discrete optical components through microassembly strategies such as pick and place.

  • Strip-loaded waveguides on thin-film lithium niobate realized via multi-photon lithography

    by Alexandra Rittmeier, Philipp Gehrke, Muhamed A. Sewidan, Elisavet Chatzizyrli, Angeliki Afentaki, Gerd-Albert Hoffmann, Joerg Neumann, Andreas Wienke, Dietmar Kracht, Michael Kues, et al.

    Integrated photonics play a pivotal role in the advancement of photonic systems in the future. The key to this lies in the research and development of novel materials and fabrication techniques. Lithium niobate (LN) is a material of particular interest due to its advantageous second-order nonlinearity and electro-optical properties. Conventionally, LN waveguides have been fabricated through multi-step processes involving lithographic patterning and dry etching techniques, which are time-consuming and laborious. In this study, we demonstrate an etchless production approach for strip-loaded thin-film LN waveguides through multi-photon lithography. The propagation losses of the fabricated waveguides are as low as 0.15 dB/cm at a wavelength of 1550 nm, which is comparable to existing etching techniques. The manufacturing approach enables a significantly reduced production time and reuse of the thin-film LN substrate. Specifically, we demonstrate the capability of erasing and reprinting polymer strips, fostering a more sustainable practice in the development of LN-based photonic integrated circuits (PICs). The approach can be transferred to other thin-film platforms and enables easier access to waveguide development, which can propel material research in the context of PIC development.


  • Open Access

    Prototype model of a 100-W fiber amplifier system with enhanced wall-plug efficiency for WDM satellite communication at 1 µm

    by Alexander Büttner, Sven Hochheim, Mathias Ernst, Peter Weßels, Jörg Neumann, Dietmar Kracht

    We present the results of our work conducted in the context of ESA’s ARTES ScyLight framework programme (SeCure and Laser Communication Technology). For the associated HydRON project (High thRoughput Optical Network), a prototype model of a fiber-based high-efficiency laser amplifier system (HELA) operating in the 1 μm wavelength range has been developed up to a technology readiness level (TRL) of 4. The laser system is intended to be employed for coherent optical communication with wavelength division multiplexing (WDM) in future high-bandwidth satellite communication networks. Combining the experience of in-house manufactured fiber components and laser systems, an all-fiber amplifier solution was designed to realize an enhanced electrical-to-optical wall-plug efficiency of around 30%. The HELA system simultaneously amplifies the 10 input channels provided by a self-designed WDM seed source, with input powers ranging from 1 to 10 mW per channel, to a total optical output power of 100 W. Here, the WDM approach combined with a singlemode, high average output power signal shall enable the realization of optical interconnections with up to Terabit per second data rates over large distances between satellites and with their corresponding ground stations.


  • Time-dependent numerical model of alexandrite lasers and comparison to experimental results

    by Stefanie Unland, Roland Kalms, Phillip Booker, Dietmar Kracht, Joerg Neumann, Peter Wessels

    We present a time-dependent numerical laser model, which is affirmed by experimental results of two different pulsed alexandrite laser regimes. The model can help to better understand the experimental findings and to determine the possible limitations of these systems. For this, the relevant temperature-dependent alexandrite transitions are incorporated, and measured data is included to generate almost the same conditions as in the laboratory. A comparison was made between the simulated and experimental results in terms of output energy, pulse duration and temporal shape, as well as laser wavelength in two different setups, a Q-switched and a cavity-dumped Q-switched system. The simulation replicated the experiment’s findings numerically, which could be demonstrated for the first time for pulsed alexandrite lasers. Additionally, the limits of the cavity-dumped Q-switched setup with respect to the shortest possible pulse length could be investigated using the numerical model.