F. Cabanettes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
F. Cabanettes has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
A. Giovenco
University of Lyon, ENISE, LTDS CNRS UMR 5513, 58 rue Jean Parot, 42023 Saint-Etienne, France
1 shared publicationC. Courbon
University of Lyon, ENISE, LTDS CNRS UMR 5513, 58 rue Jean Parot, 42023 Saint-Etienne, France
1 shared publication- Cedric Courbon
Univ Lyon, ENISE, ECL, ENTPE, CNRS, LTDS UMR 5513, F-42023, SAINT-ETIENNE, France
1 shared publication - Iñaki Mirena Arrieta
Mondragon Unibertsitatea Escuela Politecnica Superior
1 shared publication J. Rech
University of Lyon, ENISE, LTDS CNRS UMR 5513, 58 rue Jean Parot, 42023 Saint-Etienne, France
1 shared publication- Joel Rech
ECL-ENISE
1 shared publication
Latest Publications
- Open Access
- 31 May 2020
- Published by Elsevier in Procedia CIRP
- Vol. 87, 210-215
Towards the prediction of surface roughness induced by the belt finishing process: influence of the workmaterial on the roughness reduction rate
- 31 May 2020
- Published by Elsevier in Procedia CIRP
- Vol. 87, 210-215
Open AccessTowards the prediction of surface roughness induced by the belt finishing process: influence of the workmaterial on the roughness reduction rate
- 16 October 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1896 (1) , 090011
Influence of the ferritic-pearlitic steel microstructure on surface roughness in broaching of automotive steels
The aim of this work is to characterize the effect of microstructural parameters on surface roughness in dry broaching with a special emphasis on the ferrite-pearlite (FP) ratio. An experimental approach combining cutting and tribological tests has been developed on three grades 27MnCr5, C45, C60 covering a wide range of FP ratio. Fundamental broaching tests have been performed with a single tooth to analyse the resulting surface quality with uncoated M35 HSS tools. A specially designed open tribometer has been used to characterize the friction coefficient at the tool–chip–workpiece interface under appropriate conditions. Specific phenomena have been observed depending on the FP ratio and an interesting correlation with the tribological tests has been found. This clearly shows that friction has an important contribution in broaching and that phase distribution has to be highly considered when cutting a FP steel at a microscopic scale. This work also provides quantitative data of the friction coefficient depending on the sliding velocity and FP content which can be implemented in any analytical or numerical model of a broaching operation.
- 16 October 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1896 (1) , 090011
Influence of the ferritic-pearlitic steel microstructure on surface roughness in broaching of automotive steels
The aim of this work is to characterize the effect of microstructural parameters on surface roughness in dry broaching with a special emphasis on the ferrite-pearlite (FP) ratio. An experimental approach combining cutting and tribological tests has been developed on three grades 27MnCr5, C45, C60 covering a wide range of FP ratio. Fundamental broaching tests have been performed with a single tooth to analyse the resulting surface quality with uncoated M35 HSS tools. A specially designed open tribometer has been used to characterize the friction coefficient at the tool–chip–workpiece interface under appropriate conditions. Specific phenomena have been observed depending on the FP ratio and an interesting correlation with the tribological tests has been found. This clearly shows that friction has an important contribution in broaching and that phase distribution has to be highly considered when cutting a FP steel at a microscopic scale. This work also provides quantitative data of the friction coefficient depending on the sliding velocity and FP content which can be implemented in any analytical or numerical model of a broaching operation.