Jijun Tang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jijun Tang has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Chengguo Liu
College of Chemical Engineering, Jiangsu Co-Innovation Center of Efficient Processing and Utilization of Forest Resources, Jiangsu Key Lab for the Chemistry and Utilization of Agricultural and Forest Biomass, Nanjing Forestry University, Nanjing, 210037, PR China
2 shared publications - Yonghong Zhou
Institute of Chemical Industry of Forest Products, Chinese Academy of Forestry, Nanjing 210042, China
2 shared publications - Chao Yan
School of Materials Science and Engineering Jiangsu University of Science and Technology Zhenjiang People's Republic of China
1 shared publication - Cuina Wang
College of Science, Nanjing Forestry University, Nanjing 210037, China
1 shared publication - Fei Zhang
Institute of Chemical Industry of Forest Products, Chinese Academy of Forestry, Nanjing 210042, China
1 shared publication - Hongcheng Miao
Institute of Chemical Industry of Forest Products, Chinese Academy of Forestry, Nanjing 210042, China
1 shared publication
Latest Publications
- Open Access
Preparation and Properties of Plant-Oil-Based Epoxy Acrylate-Like Resins for UV-Curable Coatings
Novel oil-based epoxy acrylate (EA)-like prepolymers were synthesized via the ring-opening reaction of epoxidized plant oils with a new unsaturated carboxyl acid precursor (MAAMA) synthesized by reacting maleic anhydride (MA) with methallyl alcohol (MAA). Since the employed epoxidized oils including epoxidized soybean oil (ESO), epoxidized rubber seed oil (ERSO), and epoxidized wilsoniana seed oil (EWSO) possessed epoxy values of 7.34–4.38%, the obtained epoxy acrylate (EA)-like prepolymers (MMESO, MMERSO, and MMEWSO) indicated a C=C functionality of 7.81–4.40 per triglyceride. Furthermore, effects of the C=C functionality and the addition of hydroxyethyl methacrylate (HEMA) diluent on the ultimate properties of the resulting UV-cured EA-like materials were investigated and compared with those of commercially available acrylated ESO (AESO) resins. As the C=C functionality increased, the storage modulus at 25 °C (E’25), glass transition temperature (Tg), 5% weight–loss temperature (T5), tensile strength and modulus (σ and E), and hardness of the coating for both the pure EA and EA/HEMA resins increased significantly as well. These properties indicated similar trends when comparing the EA materials with 30% of HEMA with those pure EA materials. Specially, although ERSO had a clearly lower epoxy value that ESO, both the UV-cured pure MMERSO and MMERSO/HEMA materials showed much better E’25, Tg, σ, and E than their AESO counterparts, indicating that the MAAMA modification of epoxidized plant oils was much more effective than the modification of acrylic acid to achieve high-performance oil-based epoxy acrylate resins.
Open AccessPreparation and Properties of Plant-Oil-Based Epoxy Acrylate-Like Resins for UV-Curable Coatings
Novel oil-based epoxy acrylate (EA)-like prepolymers were synthesized via the ring-opening reaction of epoxidized plant oils with a new unsaturated carboxyl acid precursor (MAAMA) synthesized by reacting maleic anhydride (MA) with methallyl alcohol (MAA). Since the employed epoxidized oils including epoxidized soybean oil (ESO), epoxidized rubber seed oil (ERSO), and epoxidized wilsoniana seed oil (EWSO) possessed epoxy values of 7.34–4.38%, the obtained epoxy acrylate (EA)-like prepolymers (MMESO, MMERSO, and MMEWSO) indicated a C=C functionality of 7.81–4.40 per triglyceride. Furthermore, effects of the C=C functionality and the addition of hydroxyethyl methacrylate (HEMA) diluent on the ultimate properties of the resulting UV-cured EA-like materials were investigated and compared with those of commercially available acrylated ESO (AESO) resins. As the C=C functionality increased, the storage modulus at 25 °C (E’25), glass transition temperature (Tg), 5% weight–loss temperature (T5), tensile strength and modulus (σ and E), and hardness of the coating for both the pure EA and EA/HEMA resins increased significantly as well. These properties indicated similar trends when comparing the EA materials with 30% of HEMA with those pure EA materials. Specially, although ERSO had a clearly lower epoxy value that ESO, both the UV-cured pure MMERSO and MMERSO/HEMA materials showed much better E’25, Tg, σ, and E than their AESO counterparts, indicating that the MAAMA modification of epoxidized plant oils was much more effective than the modification of acrylic acid to achieve high-performance oil-based epoxy acrylate resins.
- Open Access
High-Performance Biobased Unsaturated Polyester Nanocomposites with Very Low Loadings of Graphene
Graphene-reinforced tung oil (TO)-based unsaturated polyester nanocomposites were prepared via in situ melt polycondensation intergrated with Diels–Alder addition. Functionalized graphene sheets derived from graphene oxide (GO) were then extracted from the obtained nanocomposites and carefully characterized. Furthermore, dispersion state of the graphene nanosheets in the cured polymer composites and ultimate properties of the resultant biobased nanocomposites were investigated. Mechanical and thermal properties of the TO-based unsaturated polyester resin (UPR) were greatly improved by the incorporation of GO. For example, at the optimal GO content (only 0.10 wt %), the obtained biobased nanocomposite showed tensile strength and modulus of 43.2 MPa and 2.62 GPa, and Tg of 105.2 °C, which were 159%, 191%, and 49.4% higher than those of the unreinforced UPR/TO resin, respectively. Compared to neat UPR, the biobased UPR nanocomposite with 0.1 wt % of GO even demonstrated superior comprehensive properties (comparable stiffness and Tg, while better toughness and thermal stability). Therefore, the developed biobased UPR nanocomposites are very promising to be applied in structural plastics.
Open AccessHigh-Performance Biobased Unsaturated Polyester Nanocomposites with Very Low Loadings of Graphene
Graphene-reinforced tung oil (TO)-based unsaturated polyester nanocomposites were prepared via in situ melt polycondensation intergrated with Diels–Alder addition. Functionalized graphene sheets derived from graphene oxide (GO) were then extracted from the obtained nanocomposites and carefully characterized. Furthermore, dispersion state of the graphene nanosheets in the cured polymer composites and ultimate properties of the resultant biobased nanocomposites were investigated. Mechanical and thermal properties of the TO-based unsaturated polyester resin (UPR) were greatly improved by the incorporation of GO. For example, at the optimal GO content (only 0.10 wt %), the obtained biobased nanocomposite showed tensile strength and modulus of 43.2 MPa and 2.62 GPa, and Tg of 105.2 °C, which were 159%, 191%, and 49.4% higher than those of the unreinforced UPR/TO resin, respectively. Compared to neat UPR, the biobased UPR nanocomposite with 0.1 wt % of GO even demonstrated superior comprehensive properties (comparable stiffness and Tg, while better toughness and thermal stability). Therefore, the developed biobased UPR nanocomposites are very promising to be applied in structural plastics.
- Open Access
High Efficient Reduction of Graphene Oxide via Nascent Hydrogen at Room Temperature
To develop a green and efficient method to synthesize graphene in relative milder conditions is prerequisite for graphene applications. A chemical reducing method has been developed to high efficiently reduce graphene oxide (GO) using Fe2O3 and NH3BH3 as catalyst and reductants, respectively. During the process, environmental and strong reductive nascent hydrogen were generated surrounding the surface of GO sheets by catalyst hydrolysis reaction of NH3BH3 and were used for reduction of GO. The reduction process was studied by ultraviolet absorption spectroscopy, Raman spectroscopy, and Fourier transform infrared spectrum. The structure and morphology of the reduced GO were characterized with scanning electron microscopy and transmission electron microscopy. Compared to metal (Mg/Fe/Zn/Al) particles and acid system which also use nascent hydrogen to reduce GO, this method exhibited higher reduction efficiency (43.6%). Also the reduction was carried out at room temperature condition, which is environmentally friendly. As a supercapacitor electrode, the reversible capacity of reduced graphene oxide was 113.8 F g−1 at 1 A g−1 and the capacitance retention still remained at 90% after 200 cycles. This approach provides a new method to reduce GO with high reduction efficiency by green reductant.
Open AccessHigh Efficient Reduction of Graphene Oxide via Nascent Hydrogen at Room Temperature
To develop a green and efficient method to synthesize graphene in relative milder conditions is prerequisite for graphene applications. A chemical reducing method has been developed to high efficiently reduce graphene oxide (GO) using Fe2O3 and NH3BH3 as catalyst and reductants, respectively. During the process, environmental and strong reductive nascent hydrogen were generated surrounding the surface of GO sheets by catalyst hydrolysis reaction of NH3BH3 and were used for reduction of GO. The reduction process was studied by ultraviolet absorption spectroscopy, Raman spectroscopy, and Fourier transform infrared spectrum. The structure and morphology of the reduced GO were characterized with scanning electron microscopy and transmission electron microscopy. Compared to metal (Mg/Fe/Zn/Al) particles and acid system which also use nascent hydrogen to reduce GO, this method exhibited higher reduction efficiency (43.6%). Also the reduction was carried out at room temperature condition, which is environmentally friendly. As a supercapacitor electrode, the reversible capacity of reduced graphene oxide was 113.8 F g−1 at 1 A g−1 and the capacitance retention still remained at 90% after 200 cycles. This approach provides a new method to reduce GO with high reduction efficiency by green reductant.
- 30 October 2017
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 15 (2) , 375-383
Study on a novel composite coating based on PDMS doped with modified graphene oxide
- 30 October 2017
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 15 (2) , 375-383
Study on a novel composite coating based on PDMS doped with modified graphene oxide
- Open Access
- 1 January 2015
- Published by Hindawi Limited in Advances in Materials Science and Engineering
- Vol. 2015, 1-12
A Study of Isothermal Curing of PMI Using DMA
The isothermal curing of polymethacrylimide (PMI) is studied through the use of dynamic mechanical analysis (DMA). Based on the growth rate of measured dynamic mechanical property, the relative conversion is defined to investigate the evolution of storage modulusat different curing temperatures. Hsich’s nonequilibrium thermodynamic fluctuation theory, Avrami equation, and isoconversional methods are used to analyze isothermal cure kinetics of PMI. The results show that there are different increase modes ofat low temperature range and high temperature range, respectively. In low temperature range, the relative conversion curves include a transitional stage which is found to be strongly frequency-dependent, but this stage is not observed in the relative conversion curve in high temperature range. During the isothermal curing process, the relative evolution ofcan be described by Hsich’s nonequilibrium thermodynamic fluctuation theory and Avrami equation. Moreover, the values and evolutions of activation energy are different in two temperature ranges, which suggest that the curing mechanism probably has changed.- 1 January 2015
- Published by Hindawi Limited in Advances in Materials Science and Engineering
- Vol. 2015, 1-12
Open AccessA Study of Isothermal Curing of PMI Using DMA
The isothermal curing of polymethacrylimide (PMI) is studied through the use of dynamic mechanical analysis (DMA). Based on the growth rate of measured dynamic mechanical property, the relative conversion is defined to investigate the evolution of storage modulusat different curing temperatures. Hsich’s nonequilibrium thermodynamic fluctuation theory, Avrami equation, and isoconversional methods are used to analyze isothermal cure kinetics of PMI. The results show that there are different increase modes ofat low temperature range and high temperature range, respectively. In low temperature range, the relative conversion curves include a transitional stage which is found to be strongly frequency-dependent, but this stage is not observed in the relative conversion curve in high temperature range. During the isothermal curing process, the relative evolution ofcan be described by Hsich’s nonequilibrium thermodynamic fluctuation theory and Avrami equation. Moreover, the values and evolutions of activation energy are different in two temperature ranges, which suggest that the curing mechanism probably has changed.