Krzysztof Stachon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Krzysztof Stachon has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Andrzej Siemko
CERN, Geneva Switzerland CH-1211
2 shared publications - Felix Rodriguez Mateos
CERN, Krakow, Poland
2 shared publications Giorgio D'ANgelo
2 shared publications- Andreas Will
CERN, TE, Geneva Switzerland
1 shared publication - Arjan Verweij
European Organization for Nuclear Research
1 shared publication - Arnaud Monteuuis
CERN, Geneva, Switzerland
1 shared publication
Latest Publications
- 31 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Performance of the Large Hadron Collider's Cryogenic Bypass Diodes Over the First Two Physics Runs, Future Projects, and Perspectives
Cryogenic bypass diodes have been installed in all superconducting dipole magnets (1232) and quadrupole magnets (392) of the Large Hadron Collider (LHC) at CERN, and operated during the physics runs since 2009. The bypass diodes are a fundamental ingredient of the quench protection system for those main dipoles and quadrupoles magnets. The diodes are located inside the magnet cryostats, operating in superfluid helium and exposed to ionizing radiation. The connection between the superconducting magnet and the bypass diode is made through a mechanical clamping system and copper bus bars. Since their first installation, all LHC diodes have undergone at least two full thermal cycles (from 1.9 K to room temperature and back to superfluid helium temperature). The evolution of electrical parameters as well as improvements and modifications made over a period of 10 years are reviewed in this paper. With CERN preparing for LHC's High Luminosity era, the long-term strategy for cold diodes is presented, based on the overall results and experience gathered so far, including the studies related to the tolerance with respect to the radiation doses and neutron fluences expected.
- 31 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Performance of the Large Hadron Collider's Cryogenic Bypass Diodes Over the First Two Physics Runs, Future Projects, and Perspectives
Cryogenic bypass diodes have been installed in all superconducting dipole magnets (1232) and quadrupole magnets (392) of the Large Hadron Collider (LHC) at CERN, and operated during the physics runs since 2009. The bypass diodes are a fundamental ingredient of the quench protection system for those main dipoles and quadrupoles magnets. The diodes are located inside the magnet cryostats, operating in superfluid helium and exposed to ionizing radiation. The connection between the superconducting magnet and the bypass diode is made through a mechanical clamping system and copper bus bars. Since their first installation, all LHC diodes have undergone at least two full thermal cycles (from 1.9 K to room temperature and back to superfluid helium temperature). The evolution of electrical parameters as well as improvements and modifications made over a period of 10 years are reviewed in this paper. With CERN preparing for LHC's High Luminosity era, the long-term strategy for cold diodes is presented, based on the overall results and experience gathered so far, including the studies related to the tolerance with respect to the radiation doses and neutron fluences expected.
- 13 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (3) , 1-5
Design, Assembly, and Use of a Device to Eliminate Earth Faults Caused by Metallic Debris in the LHC Main Dipole Circuits
The superconducting dipole magnets of the Large Hadron Collider operate in a superfluid helium bath at 1.9K. As a part of the magnet quench protection system, each dipole magnet is equipped with a bypass diode located in the helium bath. The connection between the superconducting magnet and the cold by-pass diode is made through a clamping system called “half-moon”, located at the lowest point of the cold-masses. This area is prone to receiving metallic debris residual from the assembly technological processes. The metallic debris might move and create an earth fault during helium flows that occur not only during the cool-down, warm-up and flushing of the cryogenic installation but also during magnet quenches at high currents. In case of appearance, the earth fault is detected by the protection system of the circuit and as a consequence, the current is ramped down to zero. Subsequently, with the circuit current already at zero, the fault can be eliminated using a device denominated as the Earth Fault Burner (EFB). The fault elimination must follow a strict procedure as it is not fully risk-free. This paper describes the details of such earth fault elimination, including preliminary diagnostics and necessary hardware. Two examples from the LHC operation are described and discussed.
- 13 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (3) , 1-5
Design, Assembly, and Use of a Device to Eliminate Earth Faults Caused by Metallic Debris in the LHC Main Dipole Circuits
The superconducting dipole magnets of the Large Hadron Collider operate in a superfluid helium bath at 1.9K. As a part of the magnet quench protection system, each dipole magnet is equipped with a bypass diode located in the helium bath. The connection between the superconducting magnet and the cold by-pass diode is made through a clamping system called “half-moon”, located at the lowest point of the cold-masses. This area is prone to receiving metallic debris residual from the assembly technological processes. The metallic debris might move and create an earth fault during helium flows that occur not only during the cool-down, warm-up and flushing of the cryogenic installation but also during magnet quenches at high currents. In case of appearance, the earth fault is detected by the protection system of the circuit and as a consequence, the current is ramped down to zero. Subsequently, with the circuit current already at zero, the fault can be eliminated using a device denominated as the Earth Fault Burner (EFB). The fault elimination must follow a strict procedure as it is not fully risk-free. This paper describes the details of such earth fault elimination, including preliminary diagnostics and necessary hardware. Two examples from the LHC operation are described and discussed.