Timo Scholehwar
Timo Scholehwar has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Alfredo Jacas
Instituto de Ciencia de Materiales de Madrid, CSIC, 28049 Madrid, Spain
1 shared publication - Antje Kynast
PI Ceramic GmbH, D-07589 Lederhose, Germany
1 shared publication - Cem Selcuk
Great Abington United Kingdom of Great Britain and Northern Ireland CB21 6AL
1 shared publication Eberhard Hennig
R&D Department, PI Ceramic GmbH, Lindenstrasse, 07589, Lederhose, Germany
1 shared publication- Franz Schubert
PI Ceramic GmbH, D-07589 Lederhose, Germany
1 shared publication - Hossein Daneshpajooh
International Center for Actuators and Transducers, The Pennsylvania State University, University Park, PA, 16802, USA
1 shared publication
Latest Publications
- Open Access
Determination of the PIC700 Ceramic’s Complex Piezo-Dielectric and Elastic Matrices from Manageable Aspect Ratio Resonators
Achieving good piezoelectric properties, such as the widely reported d33 charge coefficient, is a good starting point in establishing the potential applicability of piezoceramics. However, piezoceramics are only completely characterized by consistent piezoelectric-elastic-dielectric material coefficient matrices in complex form, i.e., including all losses. These matrices, which define the various alternative forms of the constitutive equations of piezoelectricity, are required for reliable virtual prototyping in the design of new devices. To meet this need, ten precise and accurate piezoelectric dielectric and elastic coefficients of the material, including all losses, must be determined for each alternative. Due to the difficulties arising from the coupling of modes when using the resonance method, this complete set of parameters is scarcely reported. Bi0.5Na0.5TiO3-based solid solutions are already commercially available in Europe and Japan. Here, we report a case study of the determination of these sets of material coefficients (diα, giα, eiα and hiα; sE,Dαβ and cE,Dαβ; εTik and εSik; and βTik and βSik), including all losses, of the commercial PIC700 eco-piezoceramic. Plate, disk, and cylinder ceramic resonators of a manageable aspect ratio were used to obtain all the material coefficients. The validation procedure of the matrices is also given by FEA modeling of the considered resonators.
Open AccessDetermination of the PIC700 Ceramic’s Complex Piezo-Dielectric and Elastic Matrices from Manageable Aspect Ratio Resonators
Achieving good piezoelectric properties, such as the widely reported d33 charge coefficient, is a good starting point in establishing the potential applicability of piezoceramics. However, piezoceramics are only completely characterized by consistent piezoelectric-elastic-dielectric material coefficient matrices in complex form, i.e., including all losses. These matrices, which define the various alternative forms of the constitutive equations of piezoelectricity, are required for reliable virtual prototyping in the design of new devices. To meet this need, ten precise and accurate piezoelectric dielectric and elastic coefficients of the material, including all losses, must be determined for each alternative. Due to the difficulties arising from the coupling of modes when using the resonance method, this complete set of parameters is scarcely reported. Bi0.5Na0.5TiO3-based solid solutions are already commercially available in Europe and Japan. Here, we report a case study of the determination of these sets of material coefficients (diα, giα, eiα and hiα; sE,Dαβ and cE,Dαβ; εTik and εSik; and βTik and βSik), including all losses, of the commercial PIC700 eco-piezoceramic. Plate, disk, and cylinder ceramic resonators of a manageable aspect ratio were used to obtain all the material coefficients. The validation procedure of the matrices is also given by FEA modeling of the considered resonators.
- 1 June 2021
- Published by Elsevier in Ceramics International
- Vol. 47 (11) , 16309-16315
Determination of anisotropic intensive piezoelectric loss in polycrystalline ceramics
- 1 June 2021
- Published by Elsevier in Ceramics International
- Vol. 47 (11) , 16309-16315
Determination of anisotropic intensive piezoelectric loss in polycrystalline ceramics
- Open Access
- 28 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 14 (7) , 2984-2993
Flexible Shear Mode Transducer for Structural Health Monitoring Using Ultrasonic Guided Waves
the application of the fundamental shear-horizontal wave mode for guided wave structural health monitoring is undoubtedly beneficial due its non-dispersive characteristics. Existing guided wave shear mode transducers are rigid and brittle, because of these characteristics, bonding them to irregular surfaces (i.e. curved surfaces) are challenging. There is a huge market interest in the development of a flexible shear mode transducer, which eases the transducer bonding process onto irregular surfaces and improves the surface contact between the transducer and the structure. This study presents a flexible shear mode transducer for structural health monitoring using low frequency guided waves (20-120 kHz). The proposed transducer is manufactured using piezoceramic and based on the results in this study, it exhibits the directional excitation of fundamental shear-horizontal mode at 20-120 kHz. Finite element analysis and laboratory experiments were conducted to study the behavior of the proposed transducer. Field trials were conducted on a liquid storage tank with an undulated surface (due to corrosion). The performance of the proposed transducer is also compared to the commercially available Macro Fiber Composite transducers. The proposed transducer was driven by the industrialized ultrasonic guided wave inspection system; Teletest Focus+ in line with the application of tank floor inspection using ultrasonic guided waves.
- 28 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 14 (7) , 2984-2993
Open AccessFlexible Shear Mode Transducer for Structural Health Monitoring Using Ultrasonic Guided Waves
the application of the fundamental shear-horizontal wave mode for guided wave structural health monitoring is undoubtedly beneficial due its non-dispersive characteristics. Existing guided wave shear mode transducers are rigid and brittle, because of these characteristics, bonding them to irregular surfaces (i.e. curved surfaces) are challenging. There is a huge market interest in the development of a flexible shear mode transducer, which eases the transducer bonding process onto irregular surfaces and improves the surface contact between the transducer and the structure. This study presents a flexible shear mode transducer for structural health monitoring using low frequency guided waves (20-120 kHz). The proposed transducer is manufactured using piezoceramic and based on the results in this study, it exhibits the directional excitation of fundamental shear-horizontal mode at 20-120 kHz. Finite element analysis and laboratory experiments were conducted to study the behavior of the proposed transducer. Field trials were conducted on a liquid storage tank with an undulated surface (due to corrosion). The performance of the proposed transducer is also compared to the commercially available Macro Fiber Composite transducers. The proposed transducer was driven by the industrialized ultrasonic guided wave inspection system; Teletest Focus+ in line with the application of tank floor inspection using ultrasonic guided waves.