R. S. Miranda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
R. S. Miranda has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Marcus Nogueira Lima
Department of Electrical Engineering, Federal University of Campina Grande, Campina Grande, Brazil
3 shared publications - Cursino Brandao Jacobina
Electrical Engineering, Federal University of Campina Grande, Campina Grande, Brazil
3 shared publications - Mauricio Beltrao de Rossiter Correa
Electrical Engineering Department, Universidade Federal de Alagoas, Macei, Brazil
2 shared publications - Alexandre Cunha Oliveira
Federal University of Campina Grande,Campina Grande,Brazil,58429–900
1 shared publication - E. M. Fernandes
Departamento de Engenharia Elétrica, Universidade Federal de Campina Grande, Caixa Postal 10.105, 58109-970 Campina Grande - PB - Brazil
1 shared publication - Edite Manuela da Graça Pinto Fernandes
University of Minho
1 shared publication
Latest Publications
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19388756,p. 370-376
Short-Circuit Fault Mitigation in Six-Phase Induction Machine Drives
This paper investigates a fault tolerant six phase induction machine drive. The analysis despite the presence of a short-circuit fault of a single inverter switch is presented. Performance of the motor under fault is investigated by mathematical analysis and simulations. Fault tolerant schemes that can mitigate the fault effects are presented. It is shown that the control strategy based on the inherent redundancy of voltage vectors allows for continuous and disturbance free-operation of the drive without additional hardware connections. Also, influence of the leakage inductance to limit the magnitude of circulating currents associated with the fault tolerance strategy is shown.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19388756,p. 370-376
Short-Circuit Fault Mitigation in Six-Phase Induction Machine Drives
This paper investigates a fault tolerant six phase induction machine drive. The analysis despite the presence of a short-circuit fault of a single inverter switch is presented. Performance of the motor under fault is investigated by mathematical analysis and simulations. Fault tolerant schemes that can mitigate the fault effects are presented. It is shown that the control strategy based on the inherent redundancy of voltage vectors allows for continuous and disturbance free-operation of the drive without additional hardware connections. Also, influence of the leakage inductance to limit the magnitude of circulating currents associated with the fault tolerance strategy is shown.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10482334,p. 1406-1410
Parameter and Speed Estimation for Implementing Low Speed Sensorless PMSM Drive System Based on an Algebraic Method
This paper presents a sensorless control scheme for a surface-mounted permanent-magnet synchronous machine (SM-PMSM) using the high frequency voltage signal injection method. The reactances of the high frequency model vary as a function of rotor position and a simple method based on measured high frequency currents and voltages is used to identify these reactances. Using such motor reactances, rotor position and velocity can be estimated. The proposed method is algebraic and does not require accurate knowledge of the initial value of the rotor position. The strategy was verified experimentally using a commercial SM-PMSM machine.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10482334,p. 1406-1410
Parameter and Speed Estimation for Implementing Low Speed Sensorless PMSM Drive System Based on an Algebraic Method
This paper presents a sensorless control scheme for a surface-mounted permanent-magnet synchronous machine (SM-PMSM) using the high frequency voltage signal injection method. The reactances of the high frequency model vary as a function of rotor position and a simple method based on measured high frequency currents and voltages is used to identify these reactances. Using such motor reactances, rotor position and velocity can be estimated. The proposed method is algebraic and does not require accurate knowledge of the initial value of the rotor position. The strategy was verified experimentally using a commercial SM-PMSM machine.
- 1 November 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IECON 2006 - 32nd Annual Conference on IEEE Industrial Electronics
- Vol. 34 (1553572X) , 5069-5074
Sensorless Control of a PMSM Synchronous Motor at Low Speed
This paper presents a self-sensing technique for a surface-mounted permanent-magnet synchronous machine (SM-PMSM) based on high frequency voltage injection. The reactances of the high frequency model vary as a function of rotor position and a simple method based on measured currents and voltages can be used to identify those reactances. Using the motor reactances, the rotor position and velocity are determined. The proposed technique is relatively independent of the machine parameters and it can be applied to any type of synchronous machine. The proposed technique has been tested experimentally for a commercial SM-PMSM machine. The experimental results have demonstrated the feasibility of the proposed technique
- 1 November 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IECON 2006 - 32nd Annual Conference on IEEE Industrial Electronics
- Vol. 34 (1553572X) , 5069-5074
Sensorless Control of a PMSM Synchronous Motor at Low Speed
This paper presents a self-sensing technique for a surface-mounted permanent-magnet synchronous machine (SM-PMSM) based on high frequency voltage injection. The reactances of the high frequency model vary as a function of rotor position and a simple method based on measured currents and voltages can be used to identify those reactances. Using the motor reactances, the rotor position and velocity are determined. The proposed technique is relatively independent of the machine parameters and it can be applied to any type of synchronous machine. The proposed technique has been tested experimentally for a commercial SM-PMSM machine. The experimental results have demonstrated the feasibility of the proposed technique