Angelo Scuderi
Research Subjects
Angelo Scuderi has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Egidio Ragonese
Dipartimento di Ingegneria Elettrica Elettronica e Informatica (DIEEI), University of Catania, 95125 Catania, Italy
3 shared publications - Giuseppe Palmisano
Dipartimento di Ingegneria Elettrica Elettronica e dei Sistemi, Facoltà di Ingegneria, Università di Catania, V.le. A. Doria 6, 95125, Catania, Italia
3 shared publications - Francesco Carrara
Dipartimento di Ingegneria Elettrica Elettronica e dei Sistemi, Università di Catania, Viale A. Doria 6, 95125 Catania, Italy
1 shared publication G. Bottiglieri
1 shared publicationG. Palmisano
1 shared publication- Giorgio Maiellaro
STMicroelectronics, 95121 Catania, Italy
1 shared publication
Latest Publications
- Open Access
- 31 August 2021
- Published by MDPI AG in Electronics
- Vol. 10 (17) , 2114
40 GHz VCO and Frequency Divider in 28 nm FD-SOI CMOS Technology for Automotive Radar Sensors
This paper presents a 40 GHz voltage-controlled oscillator (VCO) and frequency divider chain fabricated in STMicroelectronics 28 nm ultrathin body and box (UTBB) fully depleted silicon-on-insulator (FD-SOI) complementary metal-oxide–semiconductor (CMOS) process with eight metal layers back-end-of-line (BEOL) option. VCOs architecture is based on an LC-tank with p-type metal-oxide–semiconductor (PMOS) cross-coupled transistors. VCOs exhibit a tuning range (TR) of 3.5 GHz by exploiting two continuous frequency tuning bands selectable via a single control bit. The measured phase noise (PN) at 38 GHz carrier frequency is −94.3 and −118 dBc/Hz at 1 and 10 MHz frequency offset, respectively. The high-frequency dividers, from 40 to 5 GHz, are made using three static CMOS current-mode logic (CML) Master-Slave D-type Flip-Flop stages. The whole divider factor is 2048. A CMOS toggle flip-flop architecture working at 5 GHz was adopted for low frequency dividers. The power dissipation of the VCO core and frequency divider chain are 18 and 27.8 mW from 1.8 and 1 V supply voltages, respectively. Circuit functionality and performance were proved at three junction temperatures (i.e., −40, 25, and 125 °C) using a thermal chamber.
- 31 August 2021
- Published by MDPI AG in Electronics
- Vol. 10 (17) , 2114
Open Access40 GHz VCO and Frequency Divider in 28 nm FD-SOI CMOS Technology for Automotive Radar Sensors
This paper presents a 40 GHz voltage-controlled oscillator (VCO) and frequency divider chain fabricated in STMicroelectronics 28 nm ultrathin body and box (UTBB) fully depleted silicon-on-insulator (FD-SOI) complementary metal-oxide–semiconductor (CMOS) process with eight metal layers back-end-of-line (BEOL) option. VCOs architecture is based on an LC-tank with p-type metal-oxide–semiconductor (PMOS) cross-coupled transistors. VCOs exhibit a tuning range (TR) of 3.5 GHz by exploiting two continuous frequency tuning bands selectable via a single control bit. The measured phase noise (PN) at 38 GHz carrier frequency is −94.3 and −118 dBc/Hz at 1 and 10 MHz frequency offset, respectively. The high-frequency dividers, from 40 to 5 GHz, are made using three static CMOS current-mode logic (CML) Master-Slave D-type Flip-Flop stages. The whole divider factor is 2048. A CMOS toggle flip-flop architecture working at 5 GHz was adopted for low frequency dividers. The power dissipation of the VCO core and frequency divider chain are 18 and 27.8 mW from 1.8 and 1 V supply voltages, respectively. Circuit functionality and performance were proved at three junction temperatures (i.e., −40, 25, and 125 °C) using a thermal chamber.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1537-1540
A 0.13-¿m SiGe BiCMOS LNA for 24-GHz Automotive Short-Range Radar
In this paper a 24-GHz low-noise amplifier for automotive short-range radar applications is presented. The circuit was fabricated in a 0.13-mum SiGe BiCMOS process and includes three fully differential transformer-loaded cascode stages with variable gain functionality. The amplifier provides an outstanding power gain of 35 dB and a noise figure as low as 3.4 dB, exhibiting a reverse isolation better than -60 dB. The circuit guarantees an input 1-dB compression point of -12 dBm, while drawing 56 mA from a 2.4-V supply.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1537-1540
A 0.13-¿m SiGe BiCMOS LNA for 24-GHz Automotive Short-Range Radar
In this paper a 24-GHz low-noise amplifier for automotive short-range radar applications is presented. The circuit was fabricated in a 0.13-mum SiGe BiCMOS process and includes three fully differential transformer-loaded cascode stages with variable gain functionality. The amplifier provides an outstanding power gain of 35 dB and a noise figure as low as 3.4 dB, exhibiting a reverse isolation better than -60 dB. The circuit guarantees an input 1-dB compression point of -12 dBm, while drawing 56 mA from a 2.4-V supply.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 510-513
A O. 13-¿ SiGe BiGMOS LNA for 24-GHz Automotive Short-Range Radar
In this paper a 24-GHz low-noise amplifier for automotive short-range radar applications is presented. The circuit was fabricated in a 0.13-μm SiGe BiCMOS process and includes three fully differential transformer-loaded cascode stages with variable gain functionality. The amplifier provides an outstanding power gain of 35 dB and a noise figure as low as 3.4 dB, exhibiting a reverse isolation better than -60 dB. The circuit guarantees an input 1-dB compression point of -12 dBm, while drawing 56 mA from a 2.4-V supply.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 510-513
A O. 13-¿ SiGe BiGMOS LNA for 24-GHz Automotive Short-Range Radar
In this paper a 24-GHz low-noise amplifier for automotive short-range radar applications is presented. The circuit was fabricated in a 0.13-μm SiGe BiCMOS process and includes three fully differential transformer-loaded cascode stages with variable gain functionality. The amplifier provides an outstanding power gain of 35 dB and a noise figure as low as 3.4 dB, exhibiting a reverse isolation better than -60 dB. The circuit guarantees an input 1-dB compression point of -12 dBm, while drawing 56 mA from a 2.4-V supply.
- 1 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 931-934
An Offset Compensated Baseband Circuit for Automotive Radar Ultra-Wideband Applications
This paper presents a fully differential baseband circuit with an offset-cancellation scheme implemented in a 0.13-μm BiCMOS technology. It is part of a receiver for ultra-wideband short-range radar sensor. The circuit consists of a two-stage variable-gain amplifier with a novel digital gain control technique and an offset-compensated integrator. The variable-gain amplifier, which operates up to 1 GHz, features a maximum gain of 36 dB with 30-dB gain-control range in six steps.
- 1 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 931-934
An Offset Compensated Baseband Circuit for Automotive Radar Ultra-Wideband Applications
This paper presents a fully differential baseband circuit with an offset-cancellation scheme implemented in a 0.13-μm BiCMOS technology. It is part of a receiver for ultra-wideband short-range radar sensor. The circuit consists of a two-stage variable-gain amplifier with a novel digital gain control technique and an offset-compensated integrator. The variable-gain amplifier, which operates up to 1 GHz, features a maximum gain of 36 dB with 30-dB gain-control range in six steps.
- 27 July 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
Silicon Bipolar Linear Power Amplifier for WCDMA Mobile Applications
A monolithic 1.9-GHz linear power amplifier for wideband code-division multiple access wireless transmitters was integrated using a low-cost pure-silicon bipolar process. At a 3.3-V supply voltage, the circuit exhibits a 31-dBm saturated output power, 57% maximum power-added efficiency, and 29-dBm output 1-dB compression point, while using a low quiescent current of 80 mA. Thanks to a linearizing bias network, the power amplifier is able to comply with the standard -33-dBc adjacent-channel leakage power ratio specification up to a 28.3-dBm output power level. The circuit also features temperature-stable RF gain as well as quiescent current control and shut-down functionalities.
- 27 July 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
Silicon Bipolar Linear Power Amplifier for WCDMA Mobile Applications
A monolithic 1.9-GHz linear power amplifier for wideband code-division multiple access wireless transmitters was integrated using a low-cost pure-silicon bipolar process. At a 3.3-V supply voltage, the circuit exhibits a 31-dBm saturated output power, 57% maximum power-added efficiency, and 29-dBm output 1-dB compression point, while using a low quiescent current of 80 mA. Thanks to a linearizing bias network, the power amplifier is able to comply with the standard -33-dBc adjacent-channel leakage power ratio specification up to a 28.3-dBm output power level. The circuit also features temperature-stable RF gain as well as quiescent current control and shut-down functionalities.