MAMin Cheol Ahn

Min Cheol Ahn

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Min Cheol Ahn has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Electromagnetic Design of a 15 MW-Class HTS Flux Switching Synchronous Generator considering Mechanical Stress of the Rotor Core

    by Young Jin Hwang, Min Cheol Ahn, Jiho Lee, Yong Soo Yoon, Ho Min Kim, Yoon Do Chung, Young-Sik Jo, Tae Jung Kim, Tae Kuk Ko

    This paper introduces a novel flux switching synchronous generator (FSSG) using high-temperature superconducting (HTS) field coils. Unlike conventional superconducting synchronous generators, the HTS field coils in the proposed FSSG are mounted in the stator and do not rotate during operation. Therefore, the design and fabrication of the cooling and excitation systems for HTS field coils are easier than those for the conventional superconducting synchronous generator. To verify the feasibility of the structure, a 15 MW-class FSSG was designed using a fundamental design methodology considering the mechanical stress of the rotor core. The design methodology uses mechanical and electromagnetic equations. It defines the size of the rotor first using mechanical equations for the rotor and designs the HTS field winding and armature winding using the electromagnetic equations and an FEM analysis. In addition, the operational characteristics of the FSSG were analyzed by a transient motion analysis using the FEM program. This paper could be utilized to develop superconducting synchronous generators.


  • HTS Wire Consumption Reduction in a Coil With an Actively Controllable Magnetic Core for a Fault Current Controller

    by Min Cheol Ahn, Jae Young Jang, Tae Kuk Ko

    For an effective fault current management in a smart grid, a fault current controller (FCC) has been proposed and actively developed. A previous attempt to reduce the superconducting wire consumption in a high-temperature superconducting coil for the FCC was to use a reversely magnetized core (RMC) using permanent magnets. Despite the previous study being effective to shorten the wire, there were some potential drawbacks: a demagnetization of the permanent magnets and uncontrollability. In the smart grid with renewable sources, a nominal line current can be time-varying, so a reverse bias point should not be fixed. Therefore, an actively controllable RMC is required. In this paper, an electromagnet was applied for a source of RMC. A reverse-bias point was actively adjusted by taking account of time-varying line current. This proposed bias method could reduce wire consumption. With optimal reverse bias current, the effective inductance was 4.3 times larger than that of the air core case. If we want to make the same inductance without RMC, wire consumption should be more than 2.07 times. This proposed method was so effective to apply to the distribution class FCC, which is our final target.

  • A Study on an Algorithm for Finding Magnetic Center of an Asymmetric HTS Magnet With 3-Axis Mapper

    by Woo Seung Lee, Min Cheol Ahn, Seung-Yong Hahn, Tae Kuk Ko

    High temperature superconducting (HTS) magnets are expected to play a prominent role in future nuclear magnetic resonance (NMR) systems because not only are they an essential item to surpass the current record of NMR frequency, 1 GHz, but also they may even enable an all-HTS NMR device that can be operated without a liquid helium cryogenic environment. The HTS magnets, however, introduce many new challenges as an NMR magnet, including the large high-order harmonic field errors originated from manufacturing errors of the HTS insert, particularly the one comprised of double-pancake (DP) coils. These harmonic errors are dependent on a choice of magnetic center, i.e., a magnetic center can be defined in a way to minimize the harmonic errors in an HTS NMR magnet. This paper proposes a new algorithm to automatically find a magnetic center of an HTS magnet to minimize the target harmonic components after a “single” field mapping. With a field map given, field gradients are calculated by a harmonic analysis, and then a new magnetic center is determined, using the proposed algorithm, to minimize the target harmonic errors. These steps are recursively repeated until the “best” magnetic center is defined. A test coil was constructed and 3-D field mapping tests were performed to verify the proposed algorithm. An in-house 3-D field mapping system was used for field mappings during the experiment.

  • Characteristic Comparison for the Various Winding Methods of HTS Magnets

    by Hyun Chul Jo, Sukjin Choi, Jin Bae Na, Jae Young Jang, Young Jin Hwang, Hyung Jun Kim, Min Cheol Ahn, Yoon Do Chung, Ho Min Kim, Yong Soo Yoon, et al.

    Recently various high temperature superconducting (HTS) conductors have been commercialized in the power applications. While a BSCCO becomes tape or wire, others coated conductors (CC) are tapes. An HTS magnet utilized with these conductors can be fabricated as a form of pancake winding or layer winding. In the case of HTS magnet using a thin and rectangular tape, the pancake winding method is satisfied in the practical cases because of its suitable features. However, one of the disadvantages of this winding method is increasing brands and splices. From this point of view, we propose a layer winding method using an HTS tape and fabricated HTS layer coils. To verify the feasibility of the proposed winding method, critical current and over-current tests are investigated in liquid nitrogen and the results are compared with those of pancake coils. In addition, operating characteristics on the condition of various winding tensions are analyzed.


  • Characteristics of an HTS Coil With a Reversely Magnetized Core for the Smart Fault Current Controller

    by Min Cheol Ahn, Jae Young Jang, Tae Kuk Ko

    Recently, the smart fault current controller (FCC) was proposed in order to apply to the smart grid. The smart FCC consists of an HTS coil, an AC/DC rectifier, and a control unit. A fault current should be immediately limited by the inductance of the coil at the first peak, and then adjusted by controlling the rectifier. The larger inductance of the coil induces the lower fault current. However, a large inductance coil requires high cost and large size. To reduce the HTS conductor consumption, an HTS coil with a reversely magnetized core (RMC) was proposed. To verify the concept, two permanent magnets were installed. In this paper, various model coils were fabricated and applied to the FCC system: 1) air core, 2) open iron core, 3) closed iron core, 4) open core with RMC, and 5) closed core with RMC. Based on a comparative study on the five models, an HTS coil with a closed RMC has the lowest first peak current. The first peak current in the proposed model was 27.8% smaller than that of air core case. The experimental results show that the proposed concept is to reduce the wire consumption.


  • Parameter Determination of a Condition for Simultaneous Quench in Series-Connected YBCO Coated Conductors

    by Eung Ro Lee, Dong Keun Park, Jae Young Jang, Ki Sung Chang, Yoon Do Chung, Duck Kwon Bae, Min Cheol Ahn, Yong Soo Yoon, Tae Kuk Ko

    A simultaneous quench has been one of challenging issues in a development of a superconducting fault current limiter (SFCL) as long as series-connected superconducting materials are not identical each other. This paper deals with a parameter determination of a condition for simultaneous quench in series-connected YBCO coated conductors (CC), as a preliminary step to develop its faculties for high voltage CC applications. An electrical and thermal analysis based on the finite element method (FEM) showed that decisive parameters were critical current and n-value. For verifying the analysis, two sets of series-connected samples from a batch of AMSC 344S, which is clad on stainless steel, were short-circuit tested. One set has quite different critical current, whereas the other similar ones. The analysis estimated the quench initiation characteristics among the samples in both cases. After the verification, the condition for simultaneous quench, i.e. allowable deviation of critical current and n-value, has been obtained.


  • A Study on the Non-Inductive Coils for Hybrid Fault Current Limiter Using Experiment and Numerical Analysis

    by Jae Young Jang, Dong Keun Park, Seong Eun Yang, Young Jae Kim, Jin Bae Na, Hyun Chul Jo, Min Cheol Ahn, Tae Kuk Ko

    A Hybrid fault current limiter (FCL) proposed by our group previously is composed of a superconducting coil, a fast switch and a bypass reactor. The superconducting coil wound with two kinds of HTS wire has zero impedance when normal current flows in the coil. However, different quench characteristics of the HTS wire generate magnetic flux in the coil when fault current flows in the coil. As a result, the fast switch was opened by the repulsive force applied to the aluminum plate above the coil. In previous studies, our group verified operating characteristics and feasibility of the fast switch. In this paper, comparison of pancake type and solenoid type non-inductive coil wound with two kinds of the HTS wire was performed by using short-circuit test and finite element method. From these results, short-circuit characteristic of a coil can be acquired and magnitude of the repulsive force and magnetic field can be analysed.