Saad M. Sarwana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Saad M. Sarwana has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
A. Erik Lehmann
Hypres Inc, Elmsford, NY 10523 USA
1 shared publication- Amol Inamdar
HYPRES, Inc., Elmsford, NY, USA
1 shared publication - Anubhav Sahu
HYPRES, Inc., Elmsford, NY, USA
1 shared publication - Deepnarayan Gupta
Digital-RF Circuits & Systems, HYPRES, Elmsford, New York United States
1 shared publication - Deepnarayan Gupta
Digital-RF Circuits and Systems, Hypres, 338480 Elmsford, New York, United States
1 shared publication - Dmitri Kirichenko
Digital-RF Circuits and Systems, Hypres, 338480 Elmsford, New York, United States
1 shared publication
Latest Publications
- 21 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (7) , 1-4
Fast RSFQ and ERSFQ Parallel Counters
Historically one of the most challenging high-speed RSFQ circuits to implement has been a parallel counter that sums a set of un-weighted inputs and produces a binary-weighted word at the same clock rate. A 7-to-3 parallel counter that sums 7 inputs has been designed and tested at the target clock frequency of 40 GHz and at frequencies up to 50 GHz using its own dedicated testbed. Yielded in both 10- and 20-kA/cm2 current densities using MIT Lincoln Laboratory's foundry, this 7-to-3 summing circuit has become a digital circuit benchmark. Most recently, a version with 15 parallel inputs producing a 4-bit output at the same target frequency was designed by combining two variants of 8-to-4 parallel counters. The first variant based on the 7-to-3 parallel counter, sums 8 unweighted inputs whereas the second variant sums two 4-bit binary-weighted words by pairwise summing of bits of equal weights. Design considerations for scaling this circuit will be discussed together with the circuit performance and yield.
- 21 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (7) , 1-4
Fast RSFQ and ERSFQ Parallel Counters
Historically one of the most challenging high-speed RSFQ circuits to implement has been a parallel counter that sums a set of un-weighted inputs and produces a binary-weighted word at the same clock rate. A 7-to-3 parallel counter that sums 7 inputs has been designed and tested at the target clock frequency of 40 GHz and at frequencies up to 50 GHz using its own dedicated testbed. Yielded in both 10- and 20-kA/cm2 current densities using MIT Lincoln Laboratory's foundry, this 7-to-3 summing circuit has become a digital circuit benchmark. Most recently, a version with 15 parallel inputs producing a 4-bit output at the same target frequency was designed by combining two variants of 8-to-4 parallel counters. The first variant based on the 7-to-3 parallel counter, sums 8 unweighted inputs whereas the second variant sums two 4-bit binary-weighted words by pairwise summing of bits of equal weights. Design considerations for scaling this circuit will be discussed together with the circuit performance and yield.
- 20 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-5
Power-Optimized Temperature-Distributed Digital Data Link
Interfacing superconducting rapid single flux quantum logic with room temperature electronics requires the development of low-power semiconductor circuitry capable of operating at tens of Gb/s while maintaining sufficient signal to noise to achieve acceptable bit-error-rates. Such data-links must operate with sufficiently low power consumption to permit tens to hundreds of parallel channels to coexist in a single cryostat. This requires a careful trade-off between the power and noise performance of the cryogenically cooled digital amplifiers. Previously demonstrated ultra low-power cryogenic-to-room temperature digital data links have been limited to data rates on the order of a few Gb/s. In this paper we demonstrate a temperature distributed amplifier chain optimized for 30 Gb/s data transmission and consuming just 140 microwatts at 4 K.
- 20 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-5
Power-Optimized Temperature-Distributed Digital Data Link
Interfacing superconducting rapid single flux quantum logic with room temperature electronics requires the development of low-power semiconductor circuitry capable of operating at tens of Gb/s while maintaining sufficient signal to noise to achieve acceptable bit-error-rates. Such data-links must operate with sufficiently low power consumption to permit tens to hundreds of parallel channels to coexist in a single cryostat. This requires a careful trade-off between the power and noise performance of the cryogenically cooled digital amplifiers. Previously demonstrated ultra low-power cryogenic-to-room temperature digital data links have been limited to data rates on the order of a few Gb/s. In this paper we demonstrate a temperature distributed amplifier chain optimized for 30 Gb/s data transmission and consuming just 140 microwatts at 4 K.