Gabriele Schrag
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gabriele Schrag has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Gabriele Bosetti
Chair of Physics of Electrotechnology, Technical University of Munich, 80333 Munich, Germany
2 shared publications Gerhard Wachutka
Department of Electrical Engineering, TUM School of Computation, Information and Technology, Technical University of Munich, Munich, Germany
2 shared publications- Hesham Okeil
Department of Electrical Engineering, TUM School of Computation, Information and Technology, Technical University of Munich, Munich, Germany
2 shared publications - Johannes Manz
Infineon Technologies AG, 85579 Neubiberg, Germany
2 shared publications - Sebastian Anzinger
Infineon Technologies AG, Am Campeon 1-15, Neubiberg, Germany
2 shared publications - Alessandro Stuart Savoia
Roma Tre University
1 shared publication
Latest Publications
- Open Access
- 4 November 2026
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 413
A predictive analytical-FEM framework for energy-efficient surface acoustic wave devices via straight-IDT optimization
- 4 November 2026
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 413
Open AccessA predictive analytical-FEM framework for energy-efficient surface acoustic wave devices via straight-IDT optimization
- Open Access
- 1 August 2026
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 36 (8) , 085009
Analytic modeling of fluidic resistances inside of cantilever-based structures for microelectromechanical sensors and actuators
Acoustic microelectromechanical sensors and actuators like microphones or microspeakers often use cantilever-based structures. The fluidic resistance due to the air slit between the cantilevers plays a crucial role for acoustic key parameters like the low-frequency roll-off or the sound pressure level of such device. The opening and closing behavior of such air slits becomes complex when the displacement profile of the cantilevers is considered, leading to nonuniform slit openings, slit widths and Knudsen number-based corrections for the airflow resistance along the cantilever arc length. To extract the fluidic resistances of the air slits, the application of finite element methods (FEMs) is necessary. However, such methods require time-consuming simulations, which make the design of acoustic microelectromechanical system devices cumbersome. Using a physics-based analytic model can mitigate the computational efforts by extracting fluidic resistances utilizing microfluidic equations. The here presented model uses various geometric cantilever parameters in combination with discretizing the fluidic slit resistance along the arc length of the cantilever to calculate the fluidic resistance for each displacement. The model considers rarefied gases for small air slits of 500 nm as well as static prebending induced by e.g. residual mechanical stress in fabrication processes. A four-flap triangular cantilever structure is used to verify the derived physics-based analytic model with FEM simulations. The proposed model shows a good agreemend with the conducted FEM simulations over a large range of geometric parameters. In future work, it can be implemented in circuit simulators allowing a lumped element representation of the microphone or microspeaker.
- 1 August 2026
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 36 (8) , 085009
Open AccessAnalytic modeling of fluidic resistances inside of cantilever-based structures for microelectromechanical sensors and actuators
Acoustic microelectromechanical sensors and actuators like microphones or microspeakers often use cantilever-based structures. The fluidic resistance due to the air slit between the cantilevers plays a crucial role for acoustic key parameters like the low-frequency roll-off or the sound pressure level of such device. The opening and closing behavior of such air slits becomes complex when the displacement profile of the cantilevers is considered, leading to nonuniform slit openings, slit widths and Knudsen number-based corrections for the airflow resistance along the cantilever arc length. To extract the fluidic resistances of the air slits, the application of finite element methods (FEMs) is necessary. However, such methods require time-consuming simulations, which make the design of acoustic microelectromechanical system devices cumbersome. Using a physics-based analytic model can mitigate the computational efforts by extracting fluidic resistances utilizing microfluidic equations. The here presented model uses various geometric cantilever parameters in combination with discretizing the fluidic slit resistance along the arc length of the cantilever to calculate the fluidic resistance for each displacement. The model considers rarefied gases for small air slits of 500 nm as well as static prebending induced by e.g. residual mechanical stress in fabrication processes. A four-flap triangular cantilever structure is used to verify the derived physics-based analytic model with FEM simulations. The proposed model shows a good agreemend with the conducted FEM simulations over a large range of geometric parameters. In future work, it can be implemented in circuit simulators allowing a lumped element representation of the microphone or microspeaker.
- Open Access
- 10 June 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 44 (4)
ContaminationFlow: A Molflow+-based test-particle Monte-Carlo code for simulating contamination transfer under molecular flow conditions
We introduce the new simulation tool ContaminationFlow, a test-particle Monte-Carlo (TPMC) simulator to predict the spread of contamination in vacuum environments with a view to virtual prototyping of space vehicles and earth bound vacuum applications. The paper comprises a description of the TPMC method for transient particle transport simulations under molecular flow conditions and for long-term investigations up to several years, which is illustrated by a benchmark problem. The implemented physical models are described along with the simulation algorithm. Strengths and weaknesses of the software are evaluated as well as future measures with regard to the improvement of the prediction accuracy are pointed out.
- 10 June 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 44 (4)
Open AccessContaminationFlow: A Molflow+-based test-particle Monte-Carlo code for simulating contamination transfer under molecular flow conditions
We introduce the new simulation tool ContaminationFlow, a test-particle Monte-Carlo (TPMC) simulator to predict the spread of contamination in vacuum environments with a view to virtual prototyping of space vehicles and earth bound vacuum applications. The paper comprises a description of the TPMC method for transient particle transport simulations under molecular flow conditions and for long-term investigations up to several years, which is illustrated by a benchmark problem. The implemented physical models are described along with the simulation algorithm. Strengths and weaknesses of the software are evaluated as well as future measures with regard to the improvement of the prediction accuracy are pointed out.
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 6, 265-280
Physics-Informed Eigen-Solution Neural Networks for Ultra-Fast Simulation and Optimization of Multimodal MEMS Ultrasonic Arrays
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 6, 265-280
Open AccessPhysics-Informed Eigen-Solution Neural Networks for Ultra-Fast Simulation and Optimization of Multimodal MEMS Ultrasonic Arrays
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- p. 1-12
Enhancing Thermal Management System Simulations in Electric Vehicles Using Informed Neural Networks
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- p. 1-12
Open AccessEnhancing Thermal Management System Simulations in Electric Vehicles Using Informed Neural Networks
- Open Access
- 23 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (13) , 23966-23972
Very High-Temperature Operation and Noise-Limited Performance of 4H-SiC Lateral Magnetotransistors
4H-SiC is a key material for enabling integrated electronics and sensors that operate in very high-temperature environments. In this paper, we demonstrate the operation of 4H-SiC-based in-plane magnetic field sensitive lateral magnetotransistors across a broad range of temperatures, spanning room temperature up to 500 °C. We evaluate the magnetic field sensitivity, linearity, and electrical stability of the sensors. By conducting temperature-dependent collector current noise measurements, we determine the magnetic field detectivity up to 500 °C. A noise-limited detectivity of 3.7 μT/√Hz is achieved at 500 °C, reflecting the potential of lateral magnetotransistors for very high-temperature magnetic field sensing applications. Furthermore, we report on an anomalous slow turn-on transient behavior observed at high temperatures and discuss the possible role of extended defects.
- 23 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (13) , 23966-23972
Open AccessVery High-Temperature Operation and Noise-Limited Performance of 4H-SiC Lateral Magnetotransistors
4H-SiC is a key material for enabling integrated electronics and sensors that operate in very high-temperature environments. In this paper, we demonstrate the operation of 4H-SiC-based in-plane magnetic field sensitive lateral magnetotransistors across a broad range of temperatures, spanning room temperature up to 500 °C. We evaluate the magnetic field sensitivity, linearity, and electrical stability of the sensors. By conducting temperature-dependent collector current noise measurements, we determine the magnetic field detectivity up to 500 °C. A noise-limited detectivity of 3.7 μT/√Hz is achieved at 500 °C, reflecting the potential of lateral magnetotransistors for very high-temperature magnetic field sensing applications. Furthermore, we report on an anomalous slow turn-on transient behavior observed at high temperatures and discuss the possible role of extended defects.
- Open Access
- 21 November 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (12) , 1404
Fully Integrated MEMS Micropump and Miniaturized Mass Flow Sensor as Basic Components for a Microdosing System
Despite major advances in the field of actuator technology for microsystems, miniaturized microfluidic actuation systems for mobile devices are still not common in the market. We present a micropump concept and an associated mass flow sensor design, which, in combination, have the potential to form the basis for an integrated microfluidic development platform for microfluidic systems in general and microdosing systems in particular. The micropump combines the use of active valves with an electrostatic drive principle for the pump membrane and the valves, respectively. With a size of only 1.86 mm × 1.86 mm × 0.3 mm, the first prototypes are capable of pumping gaseous media at flow rates of up to 110 μL/min. A specific feature of the presented micropump is that the pumping direction is perpendicular to the chip surface. The corresponding flow sensor combines the principle of hot-wire anemometry with a very small footprint of only 1.4 mm × 1.4 mm × 0.4 mm. The main innovation is that the hot wires are fixed inside a through-hole in the substrate of the microchip, so that the flow direction of the fluid to be measured is perpendicular to the chip surface, which enables direct integration with the presented micropump. Detection thresholds of around 10 μL/min and measuring ranges of up to 20 mL/min can be achieved with the first prototypes, without dedicated evaluation electronics.
- 21 November 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (12) , 1404
Open AccessFully Integrated MEMS Micropump and Miniaturized Mass Flow Sensor as Basic Components for a Microdosing System
Despite major advances in the field of actuator technology for microsystems, miniaturized microfluidic actuation systems for mobile devices are still not common in the market. We present a micropump concept and an associated mass flow sensor design, which, in combination, have the potential to form the basis for an integrated microfluidic development platform for microfluidic systems in general and microdosing systems in particular. The micropump combines the use of active valves with an electrostatic drive principle for the pump membrane and the valves, respectively. With a size of only 1.86 mm × 1.86 mm × 0.3 mm, the first prototypes are capable of pumping gaseous media at flow rates of up to 110 μL/min. A specific feature of the presented micropump is that the pumping direction is perpendicular to the chip surface. The corresponding flow sensor combines the principle of hot-wire anemometry with a very small footprint of only 1.4 mm × 1.4 mm × 0.4 mm. The main innovation is that the hot wires are fixed inside a through-hole in the substrate of the microchip, so that the flow direction of the fluid to be measured is perpendicular to the chip surface, which enables direct integration with the presented micropump. Detection thresholds of around 10 μL/min and measuring ranges of up to 20 mL/min can be achieved with the first prototypes, without dedicated evaluation electronics.
- 28 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Flexible Electronics
- Vol. 3 (7) , 348-355
Conformable Electronics With Conductive Silver Structures by Electrohydrodynamic Printing
Recent advances in research and fabrication of flexible, stretchable or rather conformable electronics with printed conductive structures have enabled a wide range of applications. Various fields such as consumer electronics or wearable devices for health monitoring are affected by these achievements. Owing to gradually increasing demands on enhanced functionalities and an excellent deformability of such electronics, an investigation of appropriate hyperelastic materials and progressive manufacturing techniques are mandatory. In this article, a cost-efficient approach for fabrication of conformable electronics based on vacuum thermoforming with printed microscaled silver structures is presented. The patterns in form of conductive line arrays and meanders are realized by the emerging electrohydro-dynamic printing (EHD) technique which constitutes a promising alternative to established additive technologies due to the applicability of various printing media as well as its high material compatibility. Moreover, hyperelastic material models comprising the Mooney-Rivlin, Ogden, Neo-Hookean as well as the Yeoh model for description of stretchable thermoplastic polyurethane (TPU) during deformation are contrasted and general capabilities for design optimization of conductive structures are derived by means of numerical simulations. Based on the EHD printed metallic silver patterns on TPU with a subsequent transfer of the flat 100μm thick matrix towards a 3D-shaped electronic device by thermoforming, first demonstrators with a degree of deformation up to 57% are realized.
- 28 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Flexible Electronics
- Vol. 3 (7) , 348-355
Conformable Electronics With Conductive Silver Structures by Electrohydrodynamic Printing
Recent advances in research and fabrication of flexible, stretchable or rather conformable electronics with printed conductive structures have enabled a wide range of applications. Various fields such as consumer electronics or wearable devices for health monitoring are affected by these achievements. Owing to gradually increasing demands on enhanced functionalities and an excellent deformability of such electronics, an investigation of appropriate hyperelastic materials and progressive manufacturing techniques are mandatory. In this article, a cost-efficient approach for fabrication of conformable electronics based on vacuum thermoforming with printed microscaled silver structures is presented. The patterns in form of conductive line arrays and meanders are realized by the emerging electrohydro-dynamic printing (EHD) technique which constitutes a promising alternative to established additive technologies due to the applicability of various printing media as well as its high material compatibility. Moreover, hyperelastic material models comprising the Mooney-Rivlin, Ogden, Neo-Hookean as well as the Yeoh model for description of stretchable thermoplastic polyurethane (TPU) during deformation are contrasted and general capabilities for design optimization of conductive structures are derived by means of numerical simulations. Based on the EHD printed metallic silver patterns on TPU with a subsequent transfer of the flat 100μm thick matrix towards a 3D-shaped electronic device by thermoforming, first demonstrators with a degree of deformation up to 57% are realized.
- Open Access
- 11 April 2024
- Published by MDPI AG in Proceedings
- Vol. 97 (1) , 176
Reliable Damping Simulation of Highly Perforated Micro-Electro-Mechanical Systems through Physical Compact Modeling
We present an approach to estimate damping in highly and irregularly perforated microplates over a wide range of pressures applying physics-based compact models implemented in a flux-conserving finite network. The models are coded in Verilog A, which allows for simulation using a standard circuit simulator. This provides an efficient and customizable way to determine damping beyond the state of the art, and thus, to tailor and design the dynamic operation of MEMS in a predictive manner.
- 11 April 2024
- Published by MDPI AG in Proceedings
- Vol. 97 (1) , 176
Open AccessReliable Damping Simulation of Highly Perforated Micro-Electro-Mechanical Systems through Physical Compact Modeling
We present an approach to estimate damping in highly and irregularly perforated microplates over a wide range of pressures applying physics-based compact models implemented in a flux-conserving finite network. The models are coded in Verilog A, which allows for simulation using a standard circuit simulator. This provides an efficient and customizable way to determine damping beyond the state of the art, and thus, to tailor and design the dynamic operation of MEMS in a predictive manner.
- Open Access
- 8 April 2024
- Published by MDPI AG in Proceedings
- Vol. 97 (1) , 151
Freeform Optimization of an Ultrasonic Horn Coupled to an Airborne MEMS Transducer
We designed an ultrasonic horn using a physics-based freeform optimization method to achieve the target frequency response of an airborne ultrasonic MEMS transducer operating in transmitting mode. The radial profile of the ultrasonic horn was parametrized using a Bezier curve, and its shape was optimized using a genetic algorithm. A computationally fast compact model of the full system, wherein the horn was described analytically using transmission line theory, was used to calculate the frequency response of the transducer and evaluate the optimization objective. The result shows very good agreement with the experimental measurement of a realized prototype.
- 8 April 2024
- Published by MDPI AG in Proceedings
- Vol. 97 (1) , 151
Open AccessFreeform Optimization of an Ultrasonic Horn Coupled to an Airborne MEMS Transducer
We designed an ultrasonic horn using a physics-based freeform optimization method to achieve the target frequency response of an airborne ultrasonic MEMS transducer operating in transmitting mode. The radial profile of the ultrasonic horn was parametrized using a Bezier curve, and its shape was optimized using a genetic algorithm. A computationally fast compact model of the full system, wherein the horn was described analytically using transmission line theory, was used to calculate the frequency response of the transducer and evaluate the optimization objective. The result shows very good agreement with the experimental measurement of a realized prototype.