Pasala Sarah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pasala Sarah has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
A. R. James
Defence Metallurgical Research Lab, Kanchanbagh, Hyderabad, India
4 shared publicationsB. Mamatha
4 shared publicationsElizabeth Zacharias
Department of Physics, Faculty of Science and Technology, ICFAI foundation for Higher Education (IFHE), Hyderabad, Telangana, India
4 shared publications- Rizwana
Institute of Aeronautical Engineering, Dundigal, Hyderabad
4 shared publications Syed Mahboob
Department of Physics, MRL, Osmania University, Hyderabad, A.P., India
4 shared publications- B. Mamatha
Geethanjali College of Engineering and Technology, Hyderabad, India
3 shared publications
Latest Publications
- 3 October 2022
- Published by Taylor & Francis in Ferroelectrics
- Vol. 598 (1) , 187-196
Structural, microstructural, dielectric and ferroelectric properties of Ho3+ doped SrBi4Ti4O15 ceramics
The present work investigates microstructural, structural, ferroelectric and dielectric properties of Holmium, Ho3+, doped SrBi4Ti4O15 (SBT). Polycrystalline ceramics (SrBi4-xHoxTi4O15 SBHT, where x = 0, 0.02. and 0.03) were prepared by solid-state reaction method using high energy planetary ball mill. The surface morphology of all samples displayed dense microstructure and average grain size decreased with Holmium content increase. The XRD results of samples confirmed a single phase of SBT with orthorhombic crystal structure and a reduction in unit cell volume with the substitution of Holmium at B-site. The improvement in the structural and microstructural properties greatly enhanced the electric properties of SBHT. SBHT (x = 0.02) sample showed the improved ferroelectric properties (remnant polarization Pr = 1.63 μC/cm2 and Coercive field Ec = 0.51 kV/cm) making them suitable for ferroelectric applications. High Curie temperature (TC = 626 °C), elevated dielectric constant (εr = 236) and low loss (tanδ = 0.062) are obtained with the substitution of Ho (for x = 0.03) at B- site of SBT. These ceramics have high TC and improved thermal stability which makes these apt for the applications in high temperature sensors.
- 3 October 2022
- Published by Taylor & Francis in Ferroelectrics
- Vol. 598 (1) , 187-196
Structural, microstructural, dielectric and ferroelectric properties of Ho3+ doped SrBi4Ti4O15 ceramics
The present work investigates microstructural, structural, ferroelectric and dielectric properties of Holmium, Ho3+, doped SrBi4Ti4O15 (SBT). Polycrystalline ceramics (SrBi4-xHoxTi4O15 SBHT, where x = 0, 0.02. and 0.03) were prepared by solid-state reaction method using high energy planetary ball mill. The surface morphology of all samples displayed dense microstructure and average grain size decreased with Holmium content increase. The XRD results of samples confirmed a single phase of SBT with orthorhombic crystal structure and a reduction in unit cell volume with the substitution of Holmium at B-site. The improvement in the structural and microstructural properties greatly enhanced the electric properties of SBHT. SBHT (x = 0.02) sample showed the improved ferroelectric properties (remnant polarization Pr = 1.63 μC/cm2 and Coercive field Ec = 0.51 kV/cm) making them suitable for ferroelectric applications. High Curie temperature (TC = 626 °C), elevated dielectric constant (εr = 236) and low loss (tanδ = 0.062) are obtained with the substitution of Ho (for x = 0.03) at B- site of SBT. These ceramics have high TC and improved thermal stability which makes these apt for the applications in high temperature sensors.
- 10 December 2021
- Published by Taylor & Francis in Ferroelectrics
- Vol. 585 (1) , 1-8
Modeling of dielectric properties of Sm, Na modified SBTi ferroelectrics using modified Lorentz equation
The temperature-dependent dielectric behavior of samarium (Sm), Sodium (Na) substituted Strontium Bismuth Titanate (SBTi) ferroelectrics was explained using Lorentz and modified Lorentz equations. The validity of these equations presented was verified from obtained regression values. Dielectric data was obtained using Wayn-Kerr LCR meter from 30 °C − 700 °C. The obtained experimental data was matched with non-linear curve fitting using Lorentz and modified Lorentz equations. The modified Lorentz equation was given the best fit to experimental data, and activation energies of all the compositions were found to be in the range of 86–93 μeV.
- 10 December 2021
- Published by Taylor & Francis in Ferroelectrics
- Vol. 585 (1) , 1-8
Modeling of dielectric properties of Sm, Na modified SBTi ferroelectrics using modified Lorentz equation
The temperature-dependent dielectric behavior of samarium (Sm), Sodium (Na) substituted Strontium Bismuth Titanate (SBTi) ferroelectrics was explained using Lorentz and modified Lorentz equations. The validity of these equations presented was verified from obtained regression values. Dielectric data was obtained using Wayn-Kerr LCR meter from 30 °C − 700 °C. The obtained experimental data was matched with non-linear curve fitting using Lorentz and modified Lorentz equations. The modified Lorentz equation was given the best fit to experimental data, and activation energies of all the compositions were found to be in the range of 86–93 μeV.
- 22 November 2021
- Published by Taylor & Francis in Integrated Ferroelectrics
- Vol. 221 (1) , 245-253
Modelling of Dielectric Studies on Rare-Earth Substituted Strontium Bismuth Titanate Using Modified Lorentz Equation
Samarium, Sodium modified Strontium Bismuth Titanate ceramics were prepared using solid-state sintering approach. Calcined powders obtained after treatment at 800 °C for 120 min were pressed into1 cm diameter and 1 mm thick pellets using uniaxial hydraulic press. These pellets were sintered at 1160 °C for 120 min in a programmable furnace. XRD studies confirmed single-phase Orthorhombic structure and SEM micrographs identified the sheet-like grain formation with no preferred alignment. Dielectric data was matched with modified Lorentz equation to ensure the reliability of the obtained experimental results. The activation energies (Ea) of samples were found to be in the range 70–85 μeV.
- 22 November 2021
- Published by Taylor & Francis in Integrated Ferroelectrics
- Vol. 221 (1) , 245-253
Modelling of Dielectric Studies on Rare-Earth Substituted Strontium Bismuth Titanate Using Modified Lorentz Equation
Samarium, Sodium modified Strontium Bismuth Titanate ceramics were prepared using solid-state sintering approach. Calcined powders obtained after treatment at 800 °C for 120 min were pressed into1 cm diameter and 1 mm thick pellets using uniaxial hydraulic press. These pellets were sintered at 1160 °C for 120 min in a programmable furnace. XRD studies confirmed single-phase Orthorhombic structure and SEM micrographs identified the sheet-like grain formation with no preferred alignment. Dielectric data was matched with modified Lorentz equation to ensure the reliability of the obtained experimental results. The activation energies (Ea) of samples were found to be in the range 70–85 μeV.
- 12 April 2021
- Published by Elsevier in Solid State Communications
- Vol. 332, 114309
Investigation of the role of Sm, Na in ferroelectric, piezoelectric and conduction behaviour of Strontium Bismuth Titanate ceramics
- 12 April 2021
- Published by Elsevier in Solid State Communications
- Vol. 332, 114309
Investigation of the role of Sm, Na in ferroelectric, piezoelectric and conduction behaviour of Strontium Bismuth Titanate ceramics
- 25 January 2021
- Published by Taylor & Francis in Ferroelectrics
- Vol. 571 (1) , 61-75
Electrical studies on Na and Sm substituted strontium bismuth titanate (SBTi) ceramics
Single-phase Sodium (Na), Samarium (Sm) substituted Strontium Bismuth Titanate (SNSBTi I-V) ceramics were synthesized by solid-state double sintering approach via high energy planetary ball mill for 20 hours grinding. X-ray diffraction (XRD) study confirms the primary structure and orthorhombic distortion of crystal. Scanning electron microscopy (SEM) shows the grain orientation and densified plate-like grain structure of SNSBTi I-V. The complex impedance spectroscopy method was used to study the temperature and frequency dependent electric properties of the material using a high-frequency LCR meter. Z'' versus frequency plots have shown the peak shifting to higher frequencies with increasing concentration of Na, Sm. It is also found that the magnitude of the peaks decreases with increasing temperature. The grain and grain boundary relaxation mechanisms of SNSBTi I-V have been identified using Nyquist plots; the resistance, capacitance and relaxation times were obtained from Z-view software. It is seen that the grain and grain boundary resistances decreased with the increasing concentration of Na and Sm of SBTi ceramics.
- 25 January 2021
- Published by Taylor & Francis in Ferroelectrics
- Vol. 571 (1) , 61-75
Electrical studies on Na and Sm substituted strontium bismuth titanate (SBTi) ceramics
Single-phase Sodium (Na), Samarium (Sm) substituted Strontium Bismuth Titanate (SNSBTi I-V) ceramics were synthesized by solid-state double sintering approach via high energy planetary ball mill for 20 hours grinding. X-ray diffraction (XRD) study confirms the primary structure and orthorhombic distortion of crystal. Scanning electron microscopy (SEM) shows the grain orientation and densified plate-like grain structure of SNSBTi I-V. The complex impedance spectroscopy method was used to study the temperature and frequency dependent electric properties of the material using a high-frequency LCR meter. Z'' versus frequency plots have shown the peak shifting to higher frequencies with increasing concentration of Na, Sm. It is also found that the magnitude of the peaks decreases with increasing temperature. The grain and grain boundary relaxation mechanisms of SNSBTi I-V have been identified using Nyquist plots; the resistance, capacitance and relaxation times were obtained from Z-view software. It is seen that the grain and grain boundary resistances decreased with the increasing concentration of Na and Sm of SBTi ceramics.
- 3 April 2020
- Published by Taylor & Francis in Ferroelectrics
- Vol. 558 (1) , 79-91
Dielectric properties of sodium and neodymium substitute to A-Site SrBi4Ti4O15 ceramics
Polycrystalline ceramics, SrBi4Ti4O15 (SBT) and Sr0.2Na0.4Nd0.4Bi4Ti4O15 (SNBT), were synthesized by solid state sintering method using planetary ball mill. The stoichiometric powders were ground for 10 hours. Single phase formation was established from the XRD results. The highest peak (119) was seen at 30°. X-ray diffraction results indicated decreased cell volume and orthorhombic distortion with the substitution of Na+ and Nd3+ in place of Sr2+. The lattice parameters were measured using Unitcell software. Grain size as well as grains random orientation was observed from scanning electron microscope results. Dielectric properties were measured using Novo control dielectric analyzer, from room temperature to 1200 °C at frequencies 1 kHz, 10 kHz, 50 kHz, 100 kHz, 500 kHz, and 1 MHz. The dielectric constant and loss decreased whereas the Curie temperature increased when Na+ and Nd3+ were substituted to A- site in SBT. This ceramic has enhanced thermal stability thus making this ceramic appropriate for sensor applications at high temperatures.
- 3 April 2020
- Published by Taylor & Francis in Ferroelectrics
- Vol. 558 (1) , 79-91
Dielectric properties of sodium and neodymium substitute to A-Site SrBi4Ti4O15 ceramics
Polycrystalline ceramics, SrBi4Ti4O15 (SBT) and Sr0.2Na0.4Nd0.4Bi4Ti4O15 (SNBT), were synthesized by solid state sintering method using planetary ball mill. The stoichiometric powders were ground for 10 hours. Single phase formation was established from the XRD results. The highest peak (119) was seen at 30°. X-ray diffraction results indicated decreased cell volume and orthorhombic distortion with the substitution of Na+ and Nd3+ in place of Sr2+. The lattice parameters were measured using Unitcell software. Grain size as well as grains random orientation was observed from scanning electron microscope results. Dielectric properties were measured using Novo control dielectric analyzer, from room temperature to 1200 °C at frequencies 1 kHz, 10 kHz, 50 kHz, 100 kHz, 500 kHz, and 1 MHz. The dielectric constant and loss decreased whereas the Curie temperature increased when Na+ and Nd3+ were substituted to A- site in SBT. This ceramic has enhanced thermal stability thus making this ceramic appropriate for sensor applications at high temperatures.
- 10 December 2018
- Published by Taylor & Francis in Ferroelectrics
- Vol. 537 (1) , 237-245
Effect of Sm and Na substitution on dielectric properties of SrBi 4 Ti 4 O 15
The synthesis, characterisation, density and dielectric properties of Sm and Na substituted SrBi4Ti4O15 (SBT) piezoelectric ceramics are systematically studied for possible applications at high temperatures. The existing piezoceramics have temperature limitations. Samarium (Sm) and Sodium (Na) modified Strontium bismuth titanate Sr1-x SmxNaxBi4Ti4O15 (SSNBT-Strontium Samarium Sodium Bismuth Titanate) where x = 0.1, 0.2, 0.3 ceramics are prepared by solid state double sintering method using planetary ball mill for 10 hours duration in presence of Acetone media. Single phase is formed after calcination at 800 °C for 2 hours. Pellets are made with 1 cm diameter and 1 mm thickness using uniaxial Hydraulic press at 5 tonnes/cm2 pressure. All the samples are sintered at 1160 °C for 2 hours. The entire calcination and sintering processes are done in a programmable furnace. Orthorhombic structure of compound is confirmed by XRD analysis. The lattice parameters were calculated and experimental density was found to be around 95% of theoretical density. Tolerance factor decreased with increasing concentration of Sm, Na. The plate-like structure of grains is observed using SEM images and orientation of grains is random. Dielectric properties are reported as a function of temperature at different frequencies. The Curie temperature (Tc) of SBT is enhanced by substitution of Sm and Na in place of Strontium making this material a useful piezoceramic for high temperatures applications.
- 10 December 2018
- Published by Taylor & Francis in Ferroelectrics
- Vol. 537 (1) , 237-245
Effect of Sm and Na substitution on dielectric properties of SrBi 4 Ti 4 O 15
The synthesis, characterisation, density and dielectric properties of Sm and Na substituted SrBi4Ti4O15 (SBT) piezoelectric ceramics are systematically studied for possible applications at high temperatures. The existing piezoceramics have temperature limitations. Samarium (Sm) and Sodium (Na) modified Strontium bismuth titanate Sr1-x SmxNaxBi4Ti4O15 (SSNBT-Strontium Samarium Sodium Bismuth Titanate) where x = 0.1, 0.2, 0.3 ceramics are prepared by solid state double sintering method using planetary ball mill for 10 hours duration in presence of Acetone media. Single phase is formed after calcination at 800 °C for 2 hours. Pellets are made with 1 cm diameter and 1 mm thickness using uniaxial Hydraulic press at 5 tonnes/cm2 pressure. All the samples are sintered at 1160 °C for 2 hours. The entire calcination and sintering processes are done in a programmable furnace. Orthorhombic structure of compound is confirmed by XRD analysis. The lattice parameters were calculated and experimental density was found to be around 95% of theoretical density. Tolerance factor decreased with increasing concentration of Sm, Na. The plate-like structure of grains is observed using SEM images and orientation of grains is random. Dielectric properties are reported as a function of temperature at different frequencies. The Curie temperature (Tc) of SBT is enhanced by substitution of Sm and Na in place of Strontium making this material a useful piezoceramic for high temperatures applications.
- 4 April 2018
- Published by Taylor & Francis in Ferroelectrics
- Vol. 526 (1) , 55-60
Electromechanical coupling studies on Sr1-2xNaxNdxBi4Ti4O15 compounds in free and clamped-state for transducer application
Sr1-2xNaxNdxBi4Ti4O15 compounds were prepared through solid state sintering route. Capacitance & modulus resonance and anti-resonance behavior was observed for the ceramic samples studied under free and clamped-state respectively. Highest values of electromechanical coupling factor were observed for sample composition with x = 0.40 in the free-state. The values of Kt and Keff under free-state for this composition are 0.61 and 0.57 respectively. The value of d33, under free-state, for x = 0.0 and x = 0.4 compositions are higher when compared to other compositions and the values are 7.28 pm.V−1 and 7.03 pm.V−1 respectively. Ceramic samples studied under clamped-state showed electromechanical coupling above 99.6%. Among samples studied under clamped-state, ceramic composition with x = 0.5 showed the highest value of d33 when compared to other compositions with a value of 22.42 nm.V−1.
- 4 April 2018
- Published by Taylor & Francis in Ferroelectrics
- Vol. 526 (1) , 55-60
Electromechanical coupling studies on Sr1-2xNaxNdxBi4Ti4O15 compounds in free and clamped-state for transducer application
Sr1-2xNaxNdxBi4Ti4O15 compounds were prepared through solid state sintering route. Capacitance & modulus resonance and anti-resonance behavior was observed for the ceramic samples studied under free and clamped-state respectively. Highest values of electromechanical coupling factor were observed for sample composition with x = 0.40 in the free-state. The values of Kt and Keff under free-state for this composition are 0.61 and 0.57 respectively. The value of d33, under free-state, for x = 0.0 and x = 0.4 compositions are higher when compared to other compositions and the values are 7.28 pm.V−1 and 7.03 pm.V−1 respectively. Ceramic samples studied under clamped-state showed electromechanical coupling above 99.6%. Among samples studied under clamped-state, ceramic composition with x = 0.5 showed the highest value of d33 when compared to other compositions with a value of 22.42 nm.V−1.
- 17 February 2018
- Published by Taylor & Francis in Ferroelectrics
- Vol. 524 (1) , 86-94
Electrical properties of sodium and neodymium modified SrBi4Ti4O15 piezoelectric ceramics
Ferroelectric ceramic Sr0.8Na0.1Nd0.1Bi4Ti4O15 (SNNBT) is prepared by solid state reaction method. Single phase formation with orthorhombic structure is confirmed by X- Ray diffraction analysis. Scanning electron micrograph of the ceramic shows the plate like grains of different sizes. Dielectric properties and phase transitions are studied. Relationship of Curie temperature with ionic radii of elements is discussed. Cole-Cole plots of impedance suggest the relaxation to be non-Debye type. The activation energies are obtained in Ferro and Para electric regions from the temperature variation of dc conductivity. Piezoelectric parameters have been measured on well-densified and poled samples. This study shows that SNNBT is a proficient ceramic for applications at high temperatures.
- 17 February 2018
- Published by Taylor & Francis in Ferroelectrics
- Vol. 524 (1) , 86-94
Electrical properties of sodium and neodymium modified SrBi4Ti4O15 piezoelectric ceramics
Ferroelectric ceramic Sr0.8Na0.1Nd0.1Bi4Ti4O15 (SNNBT) is prepared by solid state reaction method. Single phase formation with orthorhombic structure is confirmed by X- Ray diffraction analysis. Scanning electron micrograph of the ceramic shows the plate like grains of different sizes. Dielectric properties and phase transitions are studied. Relationship of Curie temperature with ionic radii of elements is discussed. Cole-Cole plots of impedance suggest the relaxation to be non-Debye type. The activation energies are obtained in Ferro and Para electric regions from the temperature variation of dc conductivity. Piezoelectric parameters have been measured on well-densified and poled samples. This study shows that SNNBT is a proficient ceramic for applications at high temperatures.
- 17 February 2018
- Published by Taylor & Francis in Ferroelectrics
- Vol. 524 (1) , 95-101
Impedance and electromechancial studies on Ca0.1Sr0.9LaxBi2-xTa2O9 ceramics
Ca0.1Sr0.9LaxBi2-xTa2O9 ceramics were synthesized through solid state double sintering route. Impedance, resonance and anti-resonance studies under clamped state were carried out on the prepared ceramics. The activation energy for relaxation is within the range 0.850–1.230 eV depending up on composition x. Equivalent circuit modelling was done to the experimental Cole-Cole data so as to obtain the grain, grain boundary resistance and capacitance. The activation energy for grain conduction increased with the increase of x value except for x = 0.05 ceramic composition. The activation energy for grain boundary conduction is lower for the ceramic compositions with lanthanum doped when compared to pure CSBT ceramic. The activation energy for grain and grain boundary conduction are within the range 0.748–1.338 eV depending up on composition x and temperature. The electromechanical coupling factors are above 0.9990 and vary in fourth decimal place with the increase of temperature and composition x. The electromechanical coupling factor decreased with the increase of x value.
- 17 February 2018
- Published by Taylor & Francis in Ferroelectrics
- Vol. 524 (1) , 95-101
Impedance and electromechancial studies on Ca0.1Sr0.9LaxBi2-xTa2O9 ceramics
Ca0.1Sr0.9LaxBi2-xTa2O9 ceramics were synthesized through solid state double sintering route. Impedance, resonance and anti-resonance studies under clamped state were carried out on the prepared ceramics. The activation energy for relaxation is within the range 0.850–1.230 eV depending up on composition x. Equivalent circuit modelling was done to the experimental Cole-Cole data so as to obtain the grain, grain boundary resistance and capacitance. The activation energy for grain conduction increased with the increase of x value except for x = 0.05 ceramic composition. The activation energy for grain boundary conduction is lower for the ceramic compositions with lanthanum doped when compared to pure CSBT ceramic. The activation energy for grain and grain boundary conduction are within the range 0.748–1.338 eV depending up on composition x and temperature. The electromechanical coupling factors are above 0.9990 and vary in fourth decimal place with the increase of temperature and composition x. The electromechanical coupling factor decreased with the increase of x value.