BABirgit Awiszus

Birgit Awiszus

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Birgit Awiszus has a total of 54 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Production of Metallic Bipolar Plates Made of Stainless Steel by Incremental Hollow Embossing Using Rollers

    by Maik Fiedler, Kai Kittner, Birgit Awiszus

    As the main functional element of the fuel cell, the bipolar plate ensures the functions of media distribution, electron conduction, and mechanical stability of the entire fuel cell stack. Currently, metallic bipolar half-plates are manufactured using clocked, shaping processes (stretch forming). A transfer to a continuous forming process, such as incremental hollow embossing using rollers, promises a significant increase in productivity and, thus, profitability. Based on experimentally determined material parameters, a realistic forming simulation was set up. Significant evaluation parameters are geometric accuracy, sheet thinning, and springback. In addition, specific requirements for the manufacturing equipment have to be derived.


  • Open Access

    Study on the Milling of Additive Manufactured Components

    by Robert Laue, Pascal Colditz, Manuel Möckel, Birgit Awiszus

    Additive manufacturing of components has increased significantly in capacity; additional post-processes are usually required in order to use the components. A milling process is often used to create functional surfaces. The paper shows whether the additive manufacturing process has an influence on the milling process. For this purpose, additive manufacturing processes using powder and laser (SLM), powder and arc (3DPMD), as well as wire and arc (WAAM) of the same material are compared. Based on the microstructure and the different mechanical properties, the component properties are compared with each other and with conventional sheet metal. For this purpose, samples are cut from additively manufactured components and milled under identical conditions. The temperature and the milling forces are measured and evaluated. It is shown that the additive manufacturing process results in significant differences in machinability and that the mechanical properties alone do not provide sufficient information about the machinability.


  • Open Access

    Joining of Macroscopic 3D Steel Transition Wire Structures to Steel Sheets: Study on the Mechanical, Microstructural, and Phase Characteristics of Brazed and Glued Joints

    by Saravanan Palaniyappan, Andreas Todt, Maik Trautmann, Felix Röder, Carolin Binotsch, Birgit Awiszus, Guntram Wagner

    With an increased demand for the combination of different material classes in lightweight applications like automobiles, aircraft construction, etc., the need for simple and energy-efficient joining technologies to join these different material classes has been extensively researched over the last decades. One such hybrid material combination is the metal–plastic hybrid structure, which offers the combinational characteristics of high strength and stiffness of the metal part along with characteristic elasticity and low density of the plastic part. In this research work, the focus is laid on generating a graded property transition at the interface of metal–plastic joints by brazing a three-dimensional (3D) macroscopic transition wire structure (TWS) strucwire®, over the metal part before being molded with plastic at a later stage using an injection over-molding process. This helps in providing a mechanical interlocking facility and thereby achieving a higher load transfer at the interface of metal–plastic hybrid joints. The graded steel wire structures with different carbon content were brazed onto the galvanized steel sheets using the hotplate brazing technique. In addition to the Zinc layer on the galvanized steel sheets, electroplated Zinc coatings were fabricated on the wire structures to provide better brazing quality. The microstructural, mechanical, and intermetallic phase characteristics of the resulting brazed joints were evaluated using light microscopy, adhesion tests, and scanning electron microscopy, respectively.

  • Open Access

    Eddy Current Sensor System for Tilting Independent In-Process Measurement of Magnetic Anisotropy

    by Frank Wendler, Rohan Munjal, Muhammad Waqas, Robert Laue, Sebastian Härtel, Birgit Awiszus, Olfa Kanoun

    Modern production equipment is based on the results of quality control as well as process parameters. The magnetic anisotropy of materials is closely connected to internal mechanical stress by the Villari effect, and also to hardening effects due to plastic deformations, and could therefore provide an interesting basis for process control. Nevertheless, the analysis of anisotropic properties is extremely sensitive to sensor and workpiece misalignments, such as tilting. In this work, a novel eddy current sensor system is introduced, performing a non-contact measurement of the magnetic anisotropy of a workpiece and realizing a separation and correction of tilting effects. The measurement principle is demonstrated with the example of two samples with different magnetic anisotropy values induced by cold forming. Both samples are analyzed under different tilt angles between the sensor axis and the surface of the workpiece. In this work, digital signal processing is demonstrated on the acquired raw data in order to differentiate the effects of tilt and of anisotropy, with the use of preliminary results as an example of two prepared samples.


  • Open Access

    Addendum: Suchy, L.; et al. Influence of Hub Parameters on Joining Forces and Torque Transmission Output of Plastically Joined Shaft–Hub–Connections with a Knurled Contact Surface. Machines 2018, 6, 16

    by Lukas Suchy, Erhard Leidich, Thoralf Gerstmann, Birgit Awiszus

    The authors, while validating calculations, found discrepancies with Equations (9) and (10) in their paper

  • Open Access

    Development of a Numerical Model of the Hot Air Staking Process Based on Experimental Data

    by Sebastian Härtel, Eric Brueckner, Birgit Awiszus, Michael Gehde

    Intelligent light weight concepts are increasingly designed as multi-material systems in order to achieve optimized properties through a targeted combination of materials. For these applications, the market demands joining technologies that make it possible to join foreign materials reliably (e.g., incompatible thermoplastics, thermoplastic-metal and thermoplastic-thermoset). In view of these industrial challenges, thermoplastic staking is an established forming process. At present, computer-aided development and precise FE-simulation (finite element-simulation) of these processes are not state-of-the-art. Accordingly, the previous design is based on subjective empirical values and empirical tests of the component. Within the framework of the paper, these gaps are to be closed by the development of numerical models for the heating and forming behavior of thermal plastic rivets (hot air staking) and the associated experimental validation. This requires the experimental development of the cause-effect relationships between melt formation and the resulting forming behavior. Finally, the numerical simulation shows a high conformity to the experimental data and allows an evaluation of the minimum heating time as well as initial approaches to evaluating the resulting structures by the simulation.


  • Open Access

    A Novel Method for Improving Weld Seam Properties through Inline Coupling of Welding and Forming

    by Sebastian Härtel, Tom-Eric Adams, Kevin Hoefer, Birgit Awiszus, Peter Mayr

    High heat input during welding leads to transformations of the microstructure in the area subjected to welding, mostly resulting in an inhomogeneous microstructure and an overall deterioration of the mechanical properties. To restore these properties, post treatment processes which are typically separated from the welding process are state of the art. The present work focusses on recrystallization phenomena and shows the new methodology, WeldForming, which intends to eliminate subsequent treatment processes. The new inline process combination harnesses the synergies of a welding and a rolling process to ultimately prevent the typical zone formation of the heat affected zone. This is done by stimulating recrystallization and recovery processes. The development of the process is based on numerical simulations. A new aspect is the first time coupling of both processes in a single simulation model. The required material models were generated with the aid of thermophysical simulations. A novel approach is shown for creating a material model for the filler metal G4Si1 with the typical directed solidification microstructure. On the basis of the gained knowledge out of thermomechanical and numerical simulation, a process window was identified and a test setup was developed which gave the functional prove of the WeldForming process.


  • Open Access

    Method for Analytical Calculation of the Formability from Metallic Bipolar Plates

    by Nico Keller, Alexander Bauer, Thomas von Unwerth, Birgit Awiszus

    The constructive design of a flow field layout and the channel cross section parameters from a metallic half- or bipolar plate can have a significant influence on the performance characteristics of a fuel cell. One important aspect in the dimensioning of the channel geometry of half plates is the technical forming feasibility. In this article, first an equation is presented, which enables an analytical calculation of the channel parameters. Hereby, continuing calculations with parameter variations will be possible. Furthermore, the formability of the channel geometry of metallic half plates is evaluated through numerical and experimental investigations. Based on the results, an analytical model approach will be derived that enables an appraisal of the formability from channel cross section contours in an early development state. As a final step, the results of the numerical investigations and the analytical calculation method are compared and evaluated with the results of experimental investigations and other publications. It will be shown, that the derived analytical model approach has a good approximation compared to the effects and results from the numerical and experimental analysis. In particular, the assessment of whether a channel cross section can be manufactured safely is a result with high probability of the analytical model approach. Imprecisions happen, especially in variants with extreme geometries, for example, with very small radii or a huge channel depth. For this kind of variations, the analytical model behaves too sensitively, which makes it more difficult to estimate the damage effects. However, at an early development state, the analytical model offers a good method to get a pre-evaluation of the formability of channel cross sections with a simultaneous parameter variation possibility.


  • Open Access

    Fatigue strength of inner knurled interference fit joined by forming and cutting methods

    by Lukas Suchy, E. Leidich, A. Hasse, T. Gerstmann, B. Awiszus

    The joining of machine parts by plastic forming is a common method for transmitting forces and torque. In drive trains, the ‘knurled interference fit’ has a high transmission capacity through the combination of frictional connection and form fit. In the present study, the shaft specimen made of C45 steel material is joined with an inner knurled hub made of 16MnCr5 case hardened steel. The influence of the joining process parameters on the torsional fatigue strength of the shaft-hub connection is investigated by means of experimental studies. The most important parameter is the chamfer angle of the knurled hub, which determines the rate of strain hardening in the material and differs between the cutting and forming joining processes. This study shows that knurled interference fit connections joined by forming achieve a higher fatigue strength and a higher maximum static torque than connections joined by cutting.


  • Open Access

    Manufacturing of Metallic Bipolar Plate Channels by Rolling

    by Alexander Bauer, Sebastian Härtel, Birgit Awiszus

    Producing metallic bipolar plates for Proton Exchange Membrane (PEM) fuel cells by forming is still a topic of research. So far, it has mainly been applied for small batches, but it offers substantial advantages regarding both costs and installation space compared to the established graphite based solutions. One new possibility for an efficient manufacturing process of these metallic bipolar plates is the forming by rolling. For the first time, this technology was used for relevant industrial scale channel geometries. By the use of an experimental rolling mill, 0.1 mm thick 316L (1.4404) stainless steel foils were roll-formed to achieve previously designed channel geometries within one rolling pass. The conducted experiments show promising results regarding the forming accuracy and the shape of the channel cross-sections. With the aim for a proof of concept in the beginning and a subsequent optimization of the process, a numerical simulation was set up prior to the real experiments and later calibrated with the experimental forming results. This calibrated model was used for further improvements of the process with the objective at reducing wrinkles and distortion. The investigation of this new process method for the manufacturing of metallic bipolar plates shows enormous potential and can lead to a more efficient and cheaper production.