Yanchen Fu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yanchen Fu has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Guoqiang Xu
5 shared publicationsHaoxing Zhi
2 shared publications- Ruoyu Wang
Research Institute of Aero-Engine
2 shared publications - Yinlong Liu
School of Aerospace Science and Engineering, Lanzhou University, Lanzhou 730000, China
2 shared publications - Bensi Dong
National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics, Beihang University, Beijing 100191, China
1 shared publication - Chunhui Zhang
Nano Science and Technology Institute, University of Science and Technology of China, Hefei 230026, China
1 shared publication
Latest Publications
- 25 September 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (39) , 26785-26793
Regulating Bubble Nucleation via Gas Cavities on Superhydrophilic Surfaces
Bubble nucleation is a fundamental process governing scientific and industrial performances across pool boiling heat transfer, electrocatalytic gas evolution, and mineral flotation. Existing interfacial modulation approaches predominantly rely on constructing micro/nanostructures to lower heterogeneous nucleation energy barriers, yet overlook the pivotal contribution of surface-trapped gas cavities, which restricts the achievement of stable, precisely tailored bubble generation and hinders the development of programmable nucleation control. Herein, we fabricated a series of functional superhydrophilic surfaces with rationally designed microstructures via laser etching, which enable effective regulation of bubble nucleation behavior. Quantitative experiments establish a positive dependence of nucleation rate on surface roughness. Mechanistic characterizations and numerical simulations unambiguously demonstrate that trapped gas cavities confined within rough textures act as dominant preferential nucleation sites. At a CO2 supersaturation ratio of 0.90 ± 0.19, rough superhydrophilic surfaces retaining gas cavities exhibit a bubble nucleation rate of approximately 360 cm–2 s–1. Furthermore, bubble nucleation and release remain achievable even at a CO2 supersaturation ratio of 0.29 ± 0.11. Benefiting from the gas-cavity-dominated mechanism, scalable laser-patterned superhydrophilic surfaces are engineered to accomplish spatially localized, on-demand nucleation and directional bubble detachment, affording an effective strategy for precise manipulation of overall bubble dynamics.
- 25 September 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (39) , 26785-26793
Regulating Bubble Nucleation via Gas Cavities on Superhydrophilic Surfaces
Bubble nucleation is a fundamental process governing scientific and industrial performances across pool boiling heat transfer, electrocatalytic gas evolution, and mineral flotation. Existing interfacial modulation approaches predominantly rely on constructing micro/nanostructures to lower heterogeneous nucleation energy barriers, yet overlook the pivotal contribution of surface-trapped gas cavities, which restricts the achievement of stable, precisely tailored bubble generation and hinders the development of programmable nucleation control. Herein, we fabricated a series of functional superhydrophilic surfaces with rationally designed microstructures via laser etching, which enable effective regulation of bubble nucleation behavior. Quantitative experiments establish a positive dependence of nucleation rate on surface roughness. Mechanistic characterizations and numerical simulations unambiguously demonstrate that trapped gas cavities confined within rough textures act as dominant preferential nucleation sites. At a CO2 supersaturation ratio of 0.90 ± 0.19, rough superhydrophilic surfaces retaining gas cavities exhibit a bubble nucleation rate of approximately 360 cm–2 s–1. Furthermore, bubble nucleation and release remain achievable even at a CO2 supersaturation ratio of 0.29 ± 0.11. Benefiting from the gas-cavity-dominated mechanism, scalable laser-patterned superhydrophilic surfaces are engineered to accomplish spatially localized, on-demand nucleation and directional bubble detachment, affording an effective strategy for precise manipulation of overall bubble dynamics.
- Open Access
- 24 March 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 69
Experimental investigation of convective heat transfer to supercritical pressure n-decane and RP-3 under trans-critical and cracking states
- 24 March 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 69
Open AccessExperimental investigation of convective heat transfer to supercritical pressure n-decane and RP-3 under trans-critical and cracking states
- 23 January 2025
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 70 (2) , 827-834
Viscosity Measurements of Endothermic Propellant EHF-TU and Aviation Kerosene RP-3 under Supercritical Pressures
- 23 January 2025
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 70 (2) , 827-834
Viscosity Measurements of Endothermic Propellant EHF-TU and Aviation Kerosene RP-3 under Supercritical Pressures
- 1 November 2024
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 159, 108279
Experimental evaluation of hydrothermal performance in airfoil-fin PCHE with supercritical pressure hydrocarbon fuel
- 1 November 2024
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 159, 108279
Experimental evaluation of hydrothermal performance in airfoil-fin PCHE with supercritical pressure hydrocarbon fuel
- 10 October 2024
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 69 (11) , 3730-3738
Isobaric Specific Heat Capacity Measurement in the Trans-Critical Temperature Regions for Kerosene RP-3 under Pressures of 6–8 MPa
- 10 October 2024
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 69 (11) , 3730-3738
Isobaric Specific Heat Capacity Measurement in the Trans-Critical Temperature Regions for Kerosene RP-3 under Pressures of 6–8 MPa
- 1 January 2024
- Published by Begell House Inc. Publishers in Journal of Enhanced Heat Transfer
- Vol. 31 (5) , 33-52
FLOW AND HEAT-TRANSFER CHARACTERISTICS IN SMALL-DIAMETER TUBE BUNDLES WITH A STAGGERED LAYOUT: AN EXPERIMENTAL STUDY
While past research has primarily focused on heat transfer in larger diameter tubes, the capabilities of small-diameter tubes have often been estimated using correction factors. However, with the evolution of compact heat exchangers, conducting dedicated studies on small-diameter tube bundles has become increasingly crucial to achieve more precise conclusions. An experimental research on flow and heat-transfer characteristics of staggered tube bundles with different tube diameters (2, 3, and 5 mm) is conducted. In the experiment, the number of rows (4−12), the mass rate of the air (0.06−0.18 kg/s), and the transverse tube pitch (S1/d = 2, S1/d = 3) are variables to study the characteristics of the airside flow resistance and heat transfer. The three main conclusions of the experimental results are as follows: (1) Under the same conditions, the smaller tube diameter leads to the larger airside convective heat-transfer coefficient. Besides, the deviation between the Nusselt number of the experiment and the empirical correlation of Žukauskas is in the range between −14 and −10%; (2) The effect of transverse distance on heat transfer is not obvious, but the convective heat-transfer coefficient increases significantly with the increase of row number; (3) The external pressure drop of the tube exhibits an exponential increase with the air-flow rate. Particularly in the experimental samples with smaller diameters, the outflow resistance of the tube is noticeably higher compared to other tubes. Finally, new empirical correlations of the airside convection heat transfer for the small-diameter staggered tube bundles are fitted according to the experimental data, and it is hoped to provide a reference for the more accurate design of tube-bundle heat exchangers.
- 1 January 2024
- Published by Begell House Inc. Publishers in Journal of Enhanced Heat Transfer
- Vol. 31 (5) , 33-52
FLOW AND HEAT-TRANSFER CHARACTERISTICS IN SMALL-DIAMETER TUBE BUNDLES WITH A STAGGERED LAYOUT: AN EXPERIMENTAL STUDY
While past research has primarily focused on heat transfer in larger diameter tubes, the capabilities of small-diameter tubes have often been estimated using correction factors. However, with the evolution of compact heat exchangers, conducting dedicated studies on small-diameter tube bundles has become increasingly crucial to achieve more precise conclusions. An experimental research on flow and heat-transfer characteristics of staggered tube bundles with different tube diameters (2, 3, and 5 mm) is conducted. In the experiment, the number of rows (4−12), the mass rate of the air (0.06−0.18 kg/s), and the transverse tube pitch (S1/d = 2, S1/d = 3) are variables to study the characteristics of the airside flow resistance and heat transfer. The three main conclusions of the experimental results are as follows: (1) Under the same conditions, the smaller tube diameter leads to the larger airside convective heat-transfer coefficient. Besides, the deviation between the Nusselt number of the experiment and the empirical correlation of Žukauskas is in the range between −14 and −10%; (2) The effect of transverse distance on heat transfer is not obvious, but the convective heat-transfer coefficient increases significantly with the increase of row number; (3) The external pressure drop of the tube exhibits an exponential increase with the air-flow rate. Particularly in the experimental samples with smaller diameters, the outflow resistance of the tube is noticeably higher compared to other tubes. Finally, new empirical correlations of the airside convection heat transfer for the small-diameter staggered tube bundles are fitted according to the experimental data, and it is hoped to provide a reference for the more accurate design of tube-bundle heat exchangers.
- 13 October 2021
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 14 (6)
Multivariate Design and Analysis of Aircraft Heat Exchanger Under Multiple Working Conditions Within Flight Envelope
This paper presents a multi-condition design method for the aircraft heat exchanger (HEX), marking with lightweight, compactness, and wide range of working conditions. The quasi-traversal genetic algorithm (QT-GA) method is introduced to obtain the optimal values of five structural parameters including the height, the tube diameter, the tube pitch, and the tube rows. The QT-GA method solves the deficiency of the conventional GA in the convergence, and gives a clear correlation between design variables and outputs. Pressure drops, heat transfer, and the weight of the HEX are combined in a single objective function of GA in the HEX design, thus the optimal structure of the HEX suitable for all the working conditions can be directly obtained. After optimization, the weight of the HEX is reduced to 2.250 kg, more than 20% lower than a common weight of around 3 kg. Based on the optimal structure, the off-design performance of the HEX is further analyzed. Results show that the extreme working conditions for the heat transfer and the pressure drops are not consistent. It proves the advance of the multi-condition design method over the traditional single-condition design method. In general, the proposed QT-GA design method is an efficient way to solve the multi-condition problems related to the aircraft HEX or other energy systems.
- 13 October 2021
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 14 (6)
Multivariate Design and Analysis of Aircraft Heat Exchanger Under Multiple Working Conditions Within Flight Envelope
This paper presents a multi-condition design method for the aircraft heat exchanger (HEX), marking with lightweight, compactness, and wide range of working conditions. The quasi-traversal genetic algorithm (QT-GA) method is introduced to obtain the optimal values of five structural parameters including the height, the tube diameter, the tube pitch, and the tube rows. The QT-GA method solves the deficiency of the conventional GA in the convergence, and gives a clear correlation between design variables and outputs. Pressure drops, heat transfer, and the weight of the HEX are combined in a single objective function of GA in the HEX design, thus the optimal structure of the HEX suitable for all the working conditions can be directly obtained. After optimization, the weight of the HEX is reduced to 2.250 kg, more than 20% lower than a common weight of around 3 kg. Based on the optimal structure, the off-design performance of the HEX is further analyzed. Results show that the extreme working conditions for the heat transfer and the pressure drops are not consistent. It proves the advance of the multi-condition design method over the traditional single-condition design method. In general, the proposed QT-GA design method is an efficient way to solve the multi-condition problems related to the aircraft HEX or other energy systems.
- 21 May 2018
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 63 (6) , 1961-1968
Density Measurements of Propellant EHF-TU at (3 to 7) MPa Supercritical Pressures
- 21 May 2018
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 63 (6) , 1961-1968
Density Measurements of Propellant EHF-TU at (3 to 7) MPa Supercritical Pressures