Hossein Mardani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hossein Mardani has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Changiz Ghobadi
Department of Electrical Engineering, Urmia University, Urmia, Iran
3 shared publications - Javad Nourinia
Department of Electrical Engineering, Urmia University, Urmia, Iran
3 shared publications - Neil Buchanan
Department of EEECS, Centre for Wireless Innovation, Queens University Belfast, Belfast, U.K.
3 shared publications - Bahman Mohammadi
Department of Electrical Engineering Urmia University Urmia Iran
2 shared publications - Yat Hin Chan
Department of EEECS, Centre for Wireless Innovation, Queens University Belfast, Belfast, U.K.
2 shared publications - Abdelhady Mahmoud
Benha Faculty of Engineering, Benha University, Benha, Egypt
1 shared publication
Latest Publications
- Open Access
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 7 (3) , 918-925
Vertical Polarized Helicoid Array With Full Azimuth Beam-Scanning
This paper outlines the theory behind helicoid antenna array beamforming and the practical validation on an 8x8 helicoid antenna array. Design, simulation, and measurement are presented at 2.45 GHz. A practical method for obtaining the phase steering weights required to perform beam pointing over 360 degrees is presented. A specialised dipole was also developed, achieving 4.9 dBi and low mutual coupling. It was also shown by analysis, simulation and measurement that this type of array, unlike a planar array, does not exhibit beam pointing error, making it highly attractive for retrodirective applications when precision beam pointing is required.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 7 (3) , 918-925
Open AccessVertical Polarized Helicoid Array With Full Azimuth Beam-Scanning
This paper outlines the theory behind helicoid antenna array beamforming and the practical validation on an 8x8 helicoid antenna array. Design, simulation, and measurement are presented at 2.45 GHz. A practical method for obtaining the phase steering weights required to perform beam pointing over 360 degrees is presented. A specialised dipole was also developed, achieving 4.9 dBi and low mutual coupling. It was also shown by analysis, simulation and measurement that this type of array, unlike a planar array, does not exhibit beam pointing error, making it highly attractive for retrodirective applications when precision beam pointing is required.
- 16 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Wireless Power Technologies
- Vol. 1, 1-11
Design and Experimental Validation of a 112-Element Cross-Helix Array for Retrodirective Wireless Power Transmission
In this paper we present detailed design information and measured results of a Solar Power Satellite (SPS) power beaming array based on a 112-element cross-helix “CASSIOPeiA” Solar Power Satellite (SPS) concept, developed under the UK government DESNZ and UK space agency funded “CASSIE” research program. Designed for 2.4 GHz wireless power transmission (WPT), the array has a design goal of beaming 200 W/m2 power density over 6.5 m in an anechoic chamber, transmitting 672 W of RF power with 6 W per element. Experimental validation confirmed retrodirective beam tracking across a 360° azimuth range, with limited coverage also demonstrated in elevation. The array was comprised of 7 layers, each containing 16 elements. Power beaming tests used a 144 element rectenna, able to produce an accurate power density map across the 1m2 aperture, with a peak measured power density of 172 W/m2, reinforcing the feasibility of high-efficiency space-based solar power (SBSP), with accurate, real time, retrodirective tracking.
- 16 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Wireless Power Technologies
- Vol. 1, 1-11
Design and Experimental Validation of a 112-Element Cross-Helix Array for Retrodirective Wireless Power Transmission
In this paper we present detailed design information and measured results of a Solar Power Satellite (SPS) power beaming array based on a 112-element cross-helix “CASSIOPeiA” Solar Power Satellite (SPS) concept, developed under the UK government DESNZ and UK space agency funded “CASSIE” research program. Designed for 2.4 GHz wireless power transmission (WPT), the array has a design goal of beaming 200 W/m2 power density over 6.5 m in an anechoic chamber, transmitting 672 W of RF power with 6 W per element. Experimental validation confirmed retrodirective beam tracking across a 360° azimuth range, with limited coverage also demonstrated in elevation. The array was comprised of 7 layers, each containing 16 elements. Power beaming tests used a 144 element rectenna, able to produce an accurate power density map across the 1m2 aperture, with a peak measured power density of 172 W/m2, reinforcing the feasibility of high-efficiency space-based solar power (SBSP), with accurate, real time, retrodirective tracking.
- 7 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (6) , 3359-3367
Self-Mixing Phase Conjugator for Retrodirective Wireless Power Transfer Applications
When using retrodirective antennas for wireless power transmission it is desirable to have a high-power transmitted signal which is sent back in the same direction as a weak pilot signal to the device being powered. A significant issue arises in the retrodirective WPT transmitter in how to efficiently separate the pilot signal from the transmitted WPT signal, especially when the same antenna is being used for transmit and receive. Traditionally, this is done using either circulators or duplexers, although these components can be bulky and expensive and introduce insertion loss into the transmit path, lowering the transmit power amplifier efficiency. In this article, we propose a new self-mixing PA method using the nonlinear characteristics of a power amplifier to allow a pilot tone signal to be extracted as a lower intermediate frequency (IF) signal with no transmit insertion loss and no requirement for circulators or duplexers. We also present a completely new PLL-based phase conjugating circuit that can extract the low-frequency pilot IF signal and provide a high-power phase conjugated drive signal to the self-mixing PA. The system is experimentally validated as a six-element retrodirective array for wireless power transmission application, where the power amplifier is shown to transmit more than 10 W with efficiencies up to 84%. The self-mixing PA was also confirmed to have very low mixing conversion loss with only 6 dB loss between the received pilot signal and the low frequency IF. We see this work as being essential for applications for retrodirective antennas for space solar satellite applications and other applications where transmission and reception by only a single antenna are required.
- 7 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (6) , 3359-3367
Self-Mixing Phase Conjugator for Retrodirective Wireless Power Transfer Applications
When using retrodirective antennas for wireless power transmission it is desirable to have a high-power transmitted signal which is sent back in the same direction as a weak pilot signal to the device being powered. A significant issue arises in the retrodirective WPT transmitter in how to efficiently separate the pilot signal from the transmitted WPT signal, especially when the same antenna is being used for transmit and receive. Traditionally, this is done using either circulators or duplexers, although these components can be bulky and expensive and introduce insertion loss into the transmit path, lowering the transmit power amplifier efficiency. In this article, we propose a new self-mixing PA method using the nonlinear characteristics of a power amplifier to allow a pilot tone signal to be extracted as a lower intermediate frequency (IF) signal with no transmit insertion loss and no requirement for circulators or duplexers. We also present a completely new PLL-based phase conjugating circuit that can extract the low-frequency pilot IF signal and provide a high-power phase conjugated drive signal to the self-mixing PA. The system is experimentally validated as a six-element retrodirective array for wireless power transmission application, where the power amplifier is shown to transmit more than 10 W with efficiencies up to 84%. The self-mixing PA was also confirmed to have very low mixing conversion loss with only 6 dB loss between the received pilot signal and the low frequency IF. We see this work as being essential for applications for retrodirective antennas for space solar satellite applications and other applications where transmission and reception by only a single antenna are required.
- 17 November 2018
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 99, 1-7
A compact low-side lobes three-layer array antenna for X-band applications
- 17 November 2018
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 99, 1-7
A compact low-side lobes three-layer array antenna for X-band applications
- 8 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 17 (7) , 1334-1338
Enhanced Reflectarray Antenna Using Elements With Reduced Reflection Phase Sensitivity
An enhanced reflectarray (RA) antenna built of elements with reduced reflection phase sensitivity is presented. The proposed unit element is composed of a concentric, multi-resonance circular-ring structure with variable sizes. By changing the outer and inner radius of the interior ring in the opposite directions, a reduction in the phase sensitivity without dedicating to the 360° phase range and aggravating the losses in the unit element is achieved. Thus, this has given a good manufacturing tolerance with a high-efficiency wideband performance. Measurement results show the maximum gain of 26.4 dBi at 10 GHz, aperture efficiency of 44.27%, and 16.3% 1dB gain bandwidth. In order to improve the bandwidth of antenna, the phase constant ($\phi_{\circ}$) value at the RA aperture is gradually tuned and optimized. The designed antenna with $\phi_{\circ}$=-125° has a peak gain 26.6 dBi at 10.2 GHz, aperture efficiency of 44.56%, and the 1dB gain bandwidth is about 23.3% (9.67-12 GHz). In comparison with the conventional antenna ($\phi_{\circ}$=0°), the 1 dB bandwidth shows a 43% improvement.
- 8 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 17 (7) , 1334-1338
Enhanced Reflectarray Antenna Using Elements With Reduced Reflection Phase Sensitivity
An enhanced reflectarray (RA) antenna built of elements with reduced reflection phase sensitivity is presented. The proposed unit element is composed of a concentric, multi-resonance circular-ring structure with variable sizes. By changing the outer and inner radius of the interior ring in the opposite directions, a reduction in the phase sensitivity without dedicating to the 360° phase range and aggravating the losses in the unit element is achieved. Thus, this has given a good manufacturing tolerance with a high-efficiency wideband performance. Measurement results show the maximum gain of 26.4 dBi at 10 GHz, aperture efficiency of 44.27%, and 16.3% 1dB gain bandwidth. In order to improve the bandwidth of antenna, the phase constant ($\phi_{\circ}$) value at the RA aperture is gradually tuned and optimized. The designed antenna with $\phi_{\circ}$=-125° has a peak gain 26.6 dBi at 10.2 GHz, aperture efficiency of 44.56%, and the 1dB gain bandwidth is about 23.3% (9.67-12 GHz). In comparison with the conventional antenna ($\phi_{\circ}$=0°), the 1 dB bandwidth shows a 43% improvement.
- 1 May 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1298-1301
Novel frequency reconfigurable microstrip monopole antenna for multi-radio wireless applications
In this paper, a novel frequency reconfigurable monopole antenna with five switchable states including an ultrawideband (UWB) state, three single band states and a dualband state is presented. The frequency reconfigurable capability of the antenna is achieved by using a switchable slotted structure on the ground plane. The antenna which supports most applicable frequency bands above 2 GHz can be used in multi-radio wireless systems. Reflection coefficient and radiation pattern measurements were performed for the fabricated antenna. Good agreement between simulated and measured results was obtained.
- 1 May 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1298-1301
Novel frequency reconfigurable microstrip monopole antenna for multi-radio wireless applications
In this paper, a novel frequency reconfigurable monopole antenna with five switchable states including an ultrawideband (UWB) state, three single band states and a dualband state is presented. The frequency reconfigurable capability of the antenna is achieved by using a switchable slotted structure on the ground plane. The antenna which supports most applicable frequency bands above 2 GHz can be used in multi-radio wireless systems. Reflection coefficient and radiation pattern measurements were performed for the fabricated antenna. Good agreement between simulated and measured results was obtained.
- 1 April 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21592047,p. 1-4
An effective approach for creating multi-notch characteristics in monopole antennas
In this paper a simple rectangular monopole antenna with variable band-notched function is proposed. The antenna is constructed on a FR4-epoxy substrate by thickness of 1.6mm and ε r =4.4. The proposed antenna shows Ultra-Wideband (UWB) characteristics from around 3 up to 10.6GHz for VSWR<; 2. Two shorting pins running through the substrate connect the patch to the inverted L-shaped stubs printed on the bottom of the substrate to create multi-filtering function. By changing the stubs' lengths the proposed antenna shows variable single and double filtering characteristics.
- 1 April 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21592047,p. 1-4
An effective approach for creating multi-notch characteristics in monopole antennas
In this paper a simple rectangular monopole antenna with variable band-notched function is proposed. The antenna is constructed on a FR4-epoxy substrate by thickness of 1.6mm and ε r =4.4. The proposed antenna shows Ultra-Wideband (UWB) characteristics from around 3 up to 10.6GHz for VSWR<; 2. Two shorting pins running through the substrate connect the patch to the inverted L-shaped stubs printed on the bottom of the substrate to create multi-filtering function. By changing the stubs' lengths the proposed antenna shows variable single and double filtering characteristics.
- 1 January 2011
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Electronics Express
- Vol. 8 (20) , 1698-1702
A novel multi-notch compact monopole antenna for UWB applications
- 1 January 2011
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Electronics Express
- Vol. 8 (20) , 1698-1702
A novel multi-notch compact monopole antenna for UWB applications
- 11 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 9 (15361225) , 1076-1079
A Simple Compact Monopole Antenna With Variable Single- and Double-Filtering Function for UWB Applications
In this letter, a simple rectangular monopole antenna with variable band-notched function is proposed. The antenna is constructed on an FR4-epoxy substrate with thickness of 1.6 mm and εr = 4.4. The proposed antenna shows ultrawideband (UWB) characteristics from around 3 up to 10.6 GHz for . Two shorting pins running through the substrate connect the patch to the inverted L-shaped stubs printed on the bottom of the substrate to create multifiltering function. By changing the stubs' lengths, the proposed antenna shows variable single- and double-filtering characteristics.
- 11 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 9 (15361225) , 1076-1079
A Simple Compact Monopole Antenna With Variable Single- and Double-Filtering Function for UWB Applications
In this letter, a simple rectangular monopole antenna with variable band-notched function is proposed. The antenna is constructed on an FR4-epoxy substrate with thickness of 1.6 mm and εr = 4.4. The proposed antenna shows ultrawideband (UWB) characteristics from around 3 up to 10.6 GHz for . Two shorting pins running through the substrate connect the patch to the inverted L-shaped stubs printed on the bottom of the substrate to create multifiltering function. By changing the stubs' lengths, the proposed antenna shows variable single- and double-filtering characteristics.