Andrew Pilkington
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrew Pilkington has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Budimir Rosic
Osney Thermofluids Laboratory, University of Oxford, Oxford, OX2 0ES, UK
2 shared publicationsKoichi Tanimoto
Mitsubishi Heavy Industries Ltd., 2-1-1, Shinhama, Arai-Cho, Takasago, Hyogo, Japan
2 shared publicationsShigenari Horie
Mitsubishi Heavy Industries Ltd., 2-1-1, Shinhama, Arai-Cho, Takasago, Hyogo, Japan
2 shared publicationsB. Rosic
Unversity of Oxford
1 shared publication- Budimir Rosic
Department Engineering Science, Oxford Thermofluids Institute, University of Oxford , Oxford OX2 0ES, UK
1 shared publication - Christopher J. Barnes
Rolls-Royce plc., Derby DE24 8BJ, UK
1 shared publication
Latest Publications
- Open Access
- 2 February 2026
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 11 (1) , 9
An Experimental and Numerical Investigation into Compressor Casing Heat Shield Effectiveness
An investigation was conducted into the effectiveness of heat shields in an aero-engine compressor casing to slow down thermal time constants. The investigation used a combination of experimental measurements from a full-size compressor casing rig, combined with numerical analysis using CFD and thermal modelling. Experiments were performed on a compressor casing both with and without heat shielding in order to determine the heat shield effectiveness. Temperature measurements were taken throughout the casing in order to determine the thermal time constants. The experimental data was then used to validate a thermal model and CFD simulations of the compressor casing. The modelling allowed the heat transfer coefficients in the compressor casing to be determined from the experimentally measured time constants. It was found that the heat shields gave an increase in thermal time constant at each measured location. With a doubling in the time constant at some locations compared to the unshielded case. It was also found that the heat shields need to be fully sealed, as leakage flows significantly reduce their effectiveness.
- 2 February 2026
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 11 (1) , 9
Open AccessAn Experimental and Numerical Investigation into Compressor Casing Heat Shield Effectiveness
An investigation was conducted into the effectiveness of heat shields in an aero-engine compressor casing to slow down thermal time constants. The investigation used a combination of experimental measurements from a full-size compressor casing rig, combined with numerical analysis using CFD and thermal modelling. Experiments were performed on a compressor casing both with and without heat shielding in order to determine the heat shield effectiveness. Temperature measurements were taken throughout the casing in order to determine the thermal time constants. The experimental data was then used to validate a thermal model and CFD simulations of the compressor casing. The modelling allowed the heat transfer coefficients in the compressor casing to be determined from the experimentally measured time constants. It was found that the heat shields gave an increase in thermal time constant at each measured location. With a doubling in the time constant at some locations compared to the unshielded case. It was also found that the heat shields need to be fully sealed, as leakage flows significantly reduce their effectiveness.
- 28 August 2020
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 162, 120348
An investigation into the formation of buoyancy driven streamwise vortices
- 28 August 2020
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 162, 120348
An investigation into the formation of buoyancy driven streamwise vortices
- 26 June 2019
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 141, 233-244
Prediction of natural convection heat transfer in gas turbines
- 26 June 2019
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 141, 233-244
Prediction of natural convection heat transfer in gas turbines
- Open Access
- 12 June 2018
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 3 (2) , 17
Methods for Controlling Gas Turbine Casing Flows During Engine Shutdown
During the shutdown of a gas turbine, natural convection flows occur inside of the engine casing. These natural convection flows cause the top of the engine casing to cool more slowly than the bottom of the casing. This non-uniform cooling can cause the casing to distort, known as “cat-back” distortion. This distortion leads to reduced tip and seal clearances, which can cause rubbing and binding. In this study, two different methods for reducing the non-uniform casing heat transfer in an industrial gas turbine during shutdown were investigated. A baseline case with no active method for reducing the casing heat transfer was compared with purge and flow extraction methods. It was found that the new proposed extraction method improved the uniformity of the casing heat transfer during the initial shutdown period.
- 12 June 2018
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 3 (2) , 17
Open AccessMethods for Controlling Gas Turbine Casing Flows During Engine Shutdown
During the shutdown of a gas turbine, natural convection flows occur inside of the engine casing. These natural convection flows cause the top of the engine casing to cool more slowly than the bottom of the casing. This non-uniform cooling can cause the casing to distort, known as “cat-back” distortion. This distortion leads to reduced tip and seal clearances, which can cause rubbing and binding. In this study, two different methods for reducing the non-uniform casing heat transfer in an industrial gas turbine during shutdown were investigated. A baseline case with no active method for reducing the casing heat transfer was compared with purge and flow extraction methods. It was found that the new proposed extraction method improved the uniformity of the casing heat transfer during the initial shutdown period.