Jentsje van der Meer
Research Subjects
Jentsje van der Meer has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- André van Hoven
Deltares, Delft, The Netherlands
4 shared publications - Leopoldo Franco
Roma Tre University Rome Italy
4 shared publications - Gosse Jan Steendam
Infram Hydren, Maarn, the Netherlands
3 shared publications - Maarten Overduin
Infram Hydren, The Netherlands
3 shared publications - Thomas Lykke Andersen
Aalborg University
3 shared publications - Barbara Zanuttigh
Department of Civil, Chemical, Environmental and Materials Engineering, University of Bologna, Viale del Risorgimento 2, 40136 Bologna, Italy
2 shared publications
Latest Publications
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 44
GRASS SOD PULLING TESTS TO DETERMINE THE EROSION RESISTANCE AGAINST WAVE OVERTOPPING OF VARIOUS TYPES OF GRASS COVERS: AN ADJUSTED ANALYSIS METHOD
The erosion resistance of a grass cover against wave overtopping is characterized by the critical flow velocity. This velocity can be determined with full-scale tests with the wave overtopping simulator. However, a grass sod pulling test requires less effort and can also give a good estimation of this velocity. Within the project Future Dikes several inconsistencies were found in the analysis method used to estimate the critical flow velocity with a grass sod pulling test. To deal with these inconsistencies an adjusted analysis method was proposed. A comparison of the critical flow velocity found with wave overtopping tests and both the original and the adjusted analysis method showed that the adjusted analysis method performs better for non-failed grass covers. The original analysis method, on the other hand, performs better for failed grass covers. The reason for the difference in performance remains unclear and is subject for further research. For now it is recommended to use both analysis methods next to each other when estimating the strength of a grass cover.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 44
Open AccessGRASS SOD PULLING TESTS TO DETERMINE THE EROSION RESISTANCE AGAINST WAVE OVERTOPPING OF VARIOUS TYPES OF GRASS COVERS: AN ADJUSTED ANALYSIS METHOD
The erosion resistance of a grass cover against wave overtopping is characterized by the critical flow velocity. This velocity can be determined with full-scale tests with the wave overtopping simulator. However, a grass sod pulling test requires less effort and can also give a good estimation of this velocity. Within the project Future Dikes several inconsistencies were found in the analysis method used to estimate the critical flow velocity with a grass sod pulling test. To deal with these inconsistencies an adjusted analysis method was proposed. A comparison of the critical flow velocity found with wave overtopping tests and both the original and the adjusted analysis method showed that the adjusted analysis method performs better for non-failed grass covers. The original analysis method, on the other hand, performs better for failed grass covers. The reason for the difference in performance remains unclear and is subject for further research. For now it is recommended to use both analysis methods next to each other when estimating the strength of a grass cover.
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 68
A CASE STUDY ON THE MAJOR DAMAGE AT A PORT: DAMAGE ASSESSMENT AND UPGRADE OF THE BREAKWATER
In this study, the major damage at a commercial port located in the Southwestern Black Sea Region due to a severe storm on January 18-19, 2018 is investigated, and the experimental campaign carried out to test the performance of the upgraded breakwaters is summarized. First, the observations during the field survey that was conducted one week after the event are presented. Next, numerical wave modeling studies carried out to estimate the wave characteristics that caused the damage are described. After that, the potential reasons for the damage are discussed based on the observations from the field survey and the numerical modeling studies. Finally, the experiments focusing on the upgrade of both the trunk and head sections of the main breakwater of the port are summarized.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 68
Open AccessA CASE STUDY ON THE MAJOR DAMAGE AT A PORT: DAMAGE ASSESSMENT AND UPGRADE OF THE BREAKWATER
In this study, the major damage at a commercial port located in the Southwestern Black Sea Region due to a severe storm on January 18-19, 2018 is investigated, and the experimental campaign carried out to test the performance of the upgraded breakwaters is summarized. First, the observations during the field survey that was conducted one week after the event are presented. Next, numerical wave modeling studies carried out to estimate the wave characteristics that caused the damage are described. After that, the potential reasons for the damage are discussed based on the observations from the field survey and the numerical modeling studies. Finally, the experiments focusing on the upgrade of both the trunk and head sections of the main breakwater of the port are summarized.
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 22
IMPROVING TRANSITIONS AT GRASS COVERED DIKE SLOPES USING THE WAVE OVERTOPPING SIMULATOR
Most tests with the Wave Overtopping Simulator on grass covered dike slopes have been performed on operational dikes. They showed that transitions and obstacles reduce the strength of the grass cover. The tests in 2023 were performed on sections where innovative solutions were constructed in the dike before testing. The aim was to make transitions stronger than the grass cover itself. The governing transitions were a geometrical transition (from slope to berm) and a transition from smooth asphalt to grass on a horizontal plane. The tests showed that all innovations were successful under test conditions. Moreover, where the front velocity over a slope will increase due to gravity, a horizontal berm reduces the front velocity significantly, giving smaller loads to transitions on the berm. The present tests showed that the underlayer of boulder clay was in this case much more erosion resistant than normal clay. Finally, a cliff erosion test has been performed in order to determine whether an asphalt road on the berm may reduce or terminate cliff erosion. The road terminated cliff erosion.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 22
Open AccessIMPROVING TRANSITIONS AT GRASS COVERED DIKE SLOPES USING THE WAVE OVERTOPPING SIMULATOR
Most tests with the Wave Overtopping Simulator on grass covered dike slopes have been performed on operational dikes. They showed that transitions and obstacles reduce the strength of the grass cover. The tests in 2023 were performed on sections where innovative solutions were constructed in the dike before testing. The aim was to make transitions stronger than the grass cover itself. The governing transitions were a geometrical transition (from slope to berm) and a transition from smooth asphalt to grass on a horizontal plane. The tests showed that all innovations were successful under test conditions. Moreover, where the front velocity over a slope will increase due to gravity, a horizontal berm reduces the front velocity significantly, giving smaller loads to transitions on the berm. The present tests showed that the underlayer of boulder clay was in this case much more erosion resistant than normal clay. Finally, a cliff erosion test has been performed in order to determine whether an asphalt road on the berm may reduce or terminate cliff erosion. The road terminated cliff erosion.
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 1
WAVE, WAVE RUN-UP AND OVERTOPPING MEASUREMENTS IN THE FIELD USING LASER SCANNERS
This paper presents five years (2019 – 2024) of wave, wave run-up and overtopping measurements using two laser scanners (LIDARs) in the Eems-Dollard estuary in the north of the Netherlands during severe winter storms. The paper focuses mainly on the lessons learned: the improvements that have been made to the measurement system and analysis techniques during these five years and the interpretation and validation of the measured data. To this end, the paper describes the measured storms, the data analysis and results, which are validated with data from a radar, step gauge, ADCP, overtopping tanks in the dike, video recordings, numerical wave models and wave run-up and overtopping equations.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 1
Open AccessWAVE, WAVE RUN-UP AND OVERTOPPING MEASUREMENTS IN THE FIELD USING LASER SCANNERS
This paper presents five years (2019 – 2024) of wave, wave run-up and overtopping measurements using two laser scanners (LIDARs) in the Eems-Dollard estuary in the north of the Netherlands during severe winter storms. The paper focuses mainly on the lessons learned: the improvements that have been made to the measurement system and analysis techniques during these five years and the interpretation and validation of the measured data. To this end, the paper describes the measured storms, the data analysis and results, which are validated with data from a radar, step gauge, ADCP, overtopping tanks in the dike, video recordings, numerical wave models and wave run-up and overtopping equations.
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 70
WAVE OVERTOPPING AT VERTICAL WALLS WITH LARGE FREEBOARDS AND VARIABLE WATER DEPTH
Vertical walls serve a vital role in safeguarding coastal areas and harbors from the extreme wave conditions. These structures are typically designed for installation in deep waters (often as caissons) where conventional wave overtopping prediction methods have proven effective. Vertical walls are more common as coastal protections. However, as waves approach shallower shores, the dynamics change significantly. The onset of wave shoaling and breaking introduces impulsive conditions that pose a challenge for existing prediction methods. This research aims to deepen our understanding of wave overtopping phenomena under extreme conditions, with a particular focus on investigating mean discharge and individual wave overtopping volumes. This paper will present the follow up of the work the WOW21 project (Wave Overtopping at Walls) presented at the last ICCE 2022 in Sydney.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 70
Open AccessWAVE OVERTOPPING AT VERTICAL WALLS WITH LARGE FREEBOARDS AND VARIABLE WATER DEPTH
Vertical walls serve a vital role in safeguarding coastal areas and harbors from the extreme wave conditions. These structures are typically designed for installation in deep waters (often as caissons) where conventional wave overtopping prediction methods have proven effective. Vertical walls are more common as coastal protections. However, as waves approach shallower shores, the dynamics change significantly. The onset of wave shoaling and breaking introduces impulsive conditions that pose a challenge for existing prediction methods. This research aims to deepen our understanding of wave overtopping phenomena under extreme conditions, with a particular focus on investigating mean discharge and individual wave overtopping volumes. This paper will present the follow up of the work the WOW21 project (Wave Overtopping at Walls) presented at the last ICCE 2022 in Sydney.
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 82
A LARGE PERCHED BEACH SCHEME IN DEEP WATERS
Nowadays the need for creating land to establish new cities at more favourable locations, namely close to water, has increased. These new reclaimed cities are expanding more offshore, therefore facing severe and challenging wave conditions. Combining conventional coastal protection design (e.g. rock/concrete revetments) with these challenging conditions is expensive and non- attractive for visual, environmental and social aspects. Alternatives can be considered where hard and soft coastal protection measures are combined. Perched beaches are typically artificial beaches that are supported or partly protected at the offshore side by a (submerged) barrier. The advantages of such design schemes are that less dredged material is required than in a full “open” beach solution and less rock than in a full hard solution. At the same time, protected waters are created in front of the beach reducing the risk of significant loss of dredged material. There is a strong interaction between the barrier and the beach. The design of the barrier (quite exposed to wave action) not only depends on its standalone stability but also on the effect it has on the artificial beach, as related to the transmission performance, which is mostly influenced by the crest elevation. Moreover, water level setup and flushing are relevant aspects for safe bathing on a microtidal coast.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 82
Open AccessA LARGE PERCHED BEACH SCHEME IN DEEP WATERS
Nowadays the need for creating land to establish new cities at more favourable locations, namely close to water, has increased. These new reclaimed cities are expanding more offshore, therefore facing severe and challenging wave conditions. Combining conventional coastal protection design (e.g. rock/concrete revetments) with these challenging conditions is expensive and non- attractive for visual, environmental and social aspects. Alternatives can be considered where hard and soft coastal protection measures are combined. Perched beaches are typically artificial beaches that are supported or partly protected at the offshore side by a (submerged) barrier. The advantages of such design schemes are that less dredged material is required than in a full “open” beach solution and less rock than in a full hard solution. At the same time, protected waters are created in front of the beach reducing the risk of significant loss of dredged material. There is a strong interaction between the barrier and the beach. The design of the barrier (quite exposed to wave action) not only depends on its standalone stability but also on the effect it has on the artificial beach, as related to the transmission performance, which is mostly influenced by the crest elevation. Moreover, water level setup and flushing are relevant aspects for safe bathing on a microtidal coast.
- Open Access
- 6 May 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Wave And Wave Overtopping Measurements In A Complex Area And At A Real Dike
Wave overtopping is not easy to measure in real field situations. A 12-years long program started in 2018 to measure wind, wave and water level conditions in a complex estuary, together with wave overtopping measurements at dikes. The first winter storm was measured on 8 January 2019 and first results were described in Van der Meer et al. (2019). Wave and water level conditions are measured directly in front of the dike. Overtopping is measured with two identical overtopping boxes that were placed in the dike, but at different levels, see Figure 1. A measuring pole in front of the dike has measured wave and water level conditions for 10 years already and the design of the overtopping boxes was based on those data. In recent years, a system was invented that measures wave run-up and wave overtopping with two parallel lasers, see Figure 2. The laser scanner system was placed next to the overtopping boxes to enable a proper validation. First results were presented in Oosterlo et al. (2021a; 2021b). This paper describes the further storms that have been measured up to now, including new measurement devices, improvements to measurement devices and new analysis methods. This all brings new insights, but more storms and improvements of measurements are needed to come to a full understanding of this complex estuary.
- 6 May 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Open AccessWave And Wave Overtopping Measurements In A Complex Area And At A Real Dike
Wave overtopping is not easy to measure in real field situations. A 12-years long program started in 2018 to measure wind, wave and water level conditions in a complex estuary, together with wave overtopping measurements at dikes. The first winter storm was measured on 8 January 2019 and first results were described in Van der Meer et al. (2019). Wave and water level conditions are measured directly in front of the dike. Overtopping is measured with two identical overtopping boxes that were placed in the dike, but at different levels, see Figure 1. A measuring pole in front of the dike has measured wave and water level conditions for 10 years already and the design of the overtopping boxes was based on those data. In recent years, a system was invented that measures wave run-up and wave overtopping with two parallel lasers, see Figure 2. The laser scanner system was placed next to the overtopping boxes to enable a proper validation. First results were presented in Oosterlo et al. (2021a; 2021b). This paper describes the further storms that have been measured up to now, including new measurement devices, improvements to measurement devices and new analysis methods. This all brings new insights, but more storms and improvements of measurements are needed to come to a full understanding of this complex estuary.
- Open Access
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 19
GRASS SOD PULLING TESTS TO DETERMINE RESISTANCE AGAINST EROSION BY WAVE OVERTOPPING
From 2007 wave overtopping tests with the Wave Overtopping Simulator (Van der Meer et al, 2008) have been performed on real dikes in order to determine the strength of grass covers against loads from wave overtopping. Over 15 different locations and over 50 different test sections have been tested. Most of these large scale tests have been performed on grass covers on a clay subsoil. As part of the tests since 2014, grass pull tests with a grass sod pulling device have been performed in order to estimate the critical velocity, the strength of the grass cover, on a specific subsoil with a small and easy to perform test. The critical velocity is derived from the critical normal stresses which are calculated from the force needed to pull out the grass sod and the dimensions of the pulled sod. The method of determining the critical velocity from grass pull tests has been validated with the results of tests with the Wave Overtopping Simulator. The practical, mobile and easy to perform grass pull tests can be used to evaluate the strength of grass covers over time after seeding and for an estimation of strength of existing grass covers on different subsoils.
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 19
Open AccessGRASS SOD PULLING TESTS TO DETERMINE RESISTANCE AGAINST EROSION BY WAVE OVERTOPPING
From 2007 wave overtopping tests with the Wave Overtopping Simulator (Van der Meer et al, 2008) have been performed on real dikes in order to determine the strength of grass covers against loads from wave overtopping. Over 15 different locations and over 50 different test sections have been tested. Most of these large scale tests have been performed on grass covers on a clay subsoil. As part of the tests since 2014, grass pull tests with a grass sod pulling device have been performed in order to estimate the critical velocity, the strength of the grass cover, on a specific subsoil with a small and easy to perform test. The critical velocity is derived from the critical normal stresses which are calculated from the force needed to pull out the grass sod and the dimensions of the pulled sod. The method of determining the critical velocity from grass pull tests has been validated with the results of tests with the Wave Overtopping Simulator. The practical, mobile and easy to perform grass pull tests can be used to evaluate the strength of grass covers over time after seeding and for an estimation of strength of existing grass covers on different subsoils.
- Open Access
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 8
THE VAN DER MEER FORMULA FOR ROCK SLOPE STABILITY AT SHALLOW WATER
In Van der Meer (2021) the stability formula for rock slopes under wave attack has been rewritten to remove the mean period Tm and to include the spectral period Tm-1,0. This formula is now identical to the Modified Van der Meer formula in the Rock Manual (2007 – Eqs 5.139 and 5.140), except for its coefficients and the use of H2 percent in the Rock Manual and H1/3 in Van der Meer (2021). A method has been given in Van der Meer (2021) by coefficients cpl and csu in the rewritten formula, to include (new) data on rock slope stability where results differ from the original formula and data. The re-fit of the shallow water data by Van Gent (2004) leading to the Modified Van der Meer formula for shallow water comes now to cpl=0.92 and csu=0.96, showing that rock slopes are less stable in shallow water than in deep water (coefficients smaller than 1 show less stability). The main objective is then: when and where do shallow water stability results deviate from the known stability formulae and how can we describe the deviating results. The original dataset by Van Gent (2004) and additional tests by Eldrup (2019) as well as other data have been analysed in depth to come to an improved understanding of rock slope stability in shallow water.
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 8
Open AccessTHE VAN DER MEER FORMULA FOR ROCK SLOPE STABILITY AT SHALLOW WATER
In Van der Meer (2021) the stability formula for rock slopes under wave attack has been rewritten to remove the mean period Tm and to include the spectral period Tm-1,0. This formula is now identical to the Modified Van der Meer formula in the Rock Manual (2007 – Eqs 5.139 and 5.140), except for its coefficients and the use of H2 percent in the Rock Manual and H1/3 in Van der Meer (2021). A method has been given in Van der Meer (2021) by coefficients cpl and csu in the rewritten formula, to include (new) data on rock slope stability where results differ from the original formula and data. The re-fit of the shallow water data by Van Gent (2004) leading to the Modified Van der Meer formula for shallow water comes now to cpl=0.92 and csu=0.96, showing that rock slopes are less stable in shallow water than in deep water (coefficients smaller than 1 show less stability). The main objective is then: when and where do shallow water stability results deviate from the known stability formulae and how can we describe the deviating results. The original dataset by Van Gent (2004) and additional tests by Eldrup (2019) as well as other data have been analysed in depth to come to an improved understanding of rock slope stability in shallow water.
- Open Access
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 40
VIOLENT AND IMPULSIVE WAVE OVERTOPPING AT VERTICAL WALLS WITH LARGE FREEBOARDS
Vertical walls are designed and built to protect coastal areas or harbours. Typically, these structures are installed in relatively deep water where incoming waves are reflected without breaking. In such cases the available prediction methods for wave overtopping discharge are well established. When the relative water depth h/Hm0 becomes smaller, waves start shoaling on the foreshore and breaking can occur leading to impulsive conditions. The present overtopping prediction methods (EurOtop, 2018) under impulsive conditions have been proposed by Van der Meer and Bruce (2014) including data from the VOWS project (Bruce et al.; 2001). Wave overtopping is strongly related to the relative freeboard Rc/Hm0, and for impulsive overtopping EurOtop suggests that for Rc/Hm0 greater than 3 there still might be significant overtopping but there is no data to validate such an extrapolation. Also the well-known overtopping graphs of Goda (2000) show that overtopping could be present for very large freeboards and impulsive waves. The objective of the present research is to investigate the mean discharge and volumes per wave from impulsive and violent overtopping at vertical walls with very large freeboards (up to Rc/Hm0 = 10).
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 40
Open AccessVIOLENT AND IMPULSIVE WAVE OVERTOPPING AT VERTICAL WALLS WITH LARGE FREEBOARDS
Vertical walls are designed and built to protect coastal areas or harbours. Typically, these structures are installed in relatively deep water where incoming waves are reflected without breaking. In such cases the available prediction methods for wave overtopping discharge are well established. When the relative water depth h/Hm0 becomes smaller, waves start shoaling on the foreshore and breaking can occur leading to impulsive conditions. The present overtopping prediction methods (EurOtop, 2018) under impulsive conditions have been proposed by Van der Meer and Bruce (2014) including data from the VOWS project (Bruce et al.; 2001). Wave overtopping is strongly related to the relative freeboard Rc/Hm0, and for impulsive overtopping EurOtop suggests that for Rc/Hm0 greater than 3 there still might be significant overtopping but there is no data to validate such an extrapolation. Also the well-known overtopping graphs of Goda (2000) show that overtopping could be present for very large freeboards and impulsive waves. The objective of the present research is to investigate the mean discharge and volumes per wave from impulsive and violent overtopping at vertical walls with very large freeboards (up to Rc/Hm0 = 10).