Thomas Lykke Andersen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Thomas Lykke Andersen has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Mads Røge Eldrup
Dept. of the Built Environment, Aalborg University, Denmark
11 shared publications Mads Røge Eldrup
4 shared publications- Hans Falk Burcharth
Department of Civil Engineering, Aalborg University, 9220 Aalborg, Denmark
3 shared publications - Jentsje van der Meer
Van der Meer Consulting bv, The Netherlands
3 shared publications - Jonas Bjerg Thomsen
Department of the Built Environment, Aalborg University, Thomas Manns Vej 23, 9220 Aalborg Ø, Denmark
3 shared publications Mads Sønderstrup Røge
3 shared publications
Latest Publications
- Open Access
- 2 December 2024
- Published by TU Delft OPEN Publishing in Journal of Coastal and Hydraulic Structures
- Vol. 4
Directional Spectrum Estimation for Sea States Generated by the Single Summation Method
The influence of directional spreading of waves is significant for wave-induced loads, wave breaking and nonlinearity of the waves. For physical model testing performed at test facilities such as the Ocean and Coastal Engineering Laboratory at Aalborg University, it is crucial to validate if the test conditions match the target sea states by measurement and analysis of the generated directional wave field. Most of the existing methods assumes a double summation sea state to be present which is valid in the prototype. However, waves in the laboratory are usually generated by single summation. The current paper presents a method to analyse short-crested waves generated by the single summation method. Compared to similar methods oblique reflections are considered instead of only in-line reflections. The results show that the method successfully decomposes the incident and reflected wave fields in the time domain. Thus, for example the incident wave height distribution may be obtained. The sensitivity of the new method to additional reflective directions, noise, calibration errors and positional errors of the wave gauges was found small.
- 2 December 2024
- Published by TU Delft OPEN Publishing in Journal of Coastal and Hydraulic Structures
- Vol. 4
Open AccessDirectional Spectrum Estimation for Sea States Generated by the Single Summation Method
The influence of directional spreading of waves is significant for wave-induced loads, wave breaking and nonlinearity of the waves. For physical model testing performed at test facilities such as the Ocean and Coastal Engineering Laboratory at Aalborg University, it is crucial to validate if the test conditions match the target sea states by measurement and analysis of the generated directional wave field. Most of the existing methods assumes a double summation sea state to be present which is valid in the prototype. However, waves in the laboratory are usually generated by single summation. The current paper presents a method to analyse short-crested waves generated by the single summation method. Compared to similar methods oblique reflections are considered instead of only in-line reflections. The results show that the method successfully decomposes the incident and reflected wave fields in the time domain. Thus, for example the incident wave height distribution may be obtained. The sensitivity of the new method to additional reflective directions, noise, calibration errors and positional errors of the wave gauges was found small.
- Open Access
- 29 April 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Directional Spectrum Estimation For Sea States Generated By The Single Summation Method
The influence of directional spreading of waves is significant for wave-induced loads, wave breaking and nonlinearity of the waves. For physical model testing performed at test facilities such as the Ocean and Coastal Engineering Laboratory at Aalborg University, it is crucial to validate if the test conditions match the target sea states by measurement and analysis of the generated directional wave field. Most of the existing methods assumes a double summation sea state to be present which is valid in the prototype. However, waves in the laboratory are usually generated by single summation. The current paper presents a method to analyse short-crested waves generated by the single summation method. Compared to similar methods oblique reflections are considered instead of only in-line reflections. The results show that the method successfully decomposes the incident and reflected wave fields in the time domain. Thus, for example the incident wave height distribution may be obtained. The sensitivity of the new method to additional reflective directions, noise, calibration errors and positional errors of the wave gauges was found small.
- 29 April 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Open AccessDirectional Spectrum Estimation For Sea States Generated By The Single Summation Method
The influence of directional spreading of waves is significant for wave-induced loads, wave breaking and nonlinearity of the waves. For physical model testing performed at test facilities such as the Ocean and Coastal Engineering Laboratory at Aalborg University, it is crucial to validate if the test conditions match the target sea states by measurement and analysis of the generated directional wave field. Most of the existing methods assumes a double summation sea state to be present which is valid in the prototype. However, waves in the laboratory are usually generated by single summation. The current paper presents a method to analyse short-crested waves generated by the single summation method. Compared to similar methods oblique reflections are considered instead of only in-line reflections. The results show that the method successfully decomposes the incident and reflected wave fields in the time domain. Thus, for example the incident wave height distribution may be obtained. The sensitivity of the new method to additional reflective directions, noise, calibration errors and positional errors of the wave gauges was found small.
- Open Access
- 25 April 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Applicability Of Reflection Separation Algorithms To Nonlinear Irregular Waves Over Sloping Foreshores
In hydraulic model tests, it is common practice to relate the response of the tested structure to the incident wave parameters at the toe. Estimation of the incident wave parameters at the toe is thus an essential part of the analysis of hydraulic model testing. In many cases, the design conditions at the toe are given by waves that are highly nonlinear or even depth limited. Modelling such conditions requires reproducing the prototype foreshore slope in the model. The present paper provide guidelines on the accuracy of a nonlinear reflection separation algorithm when applied to nonlinear waves over sloping foreshores. A simple methodology has been established to estimate the expected errors on the incident wave parameters.
- 25 April 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Open AccessApplicability Of Reflection Separation Algorithms To Nonlinear Irregular Waves Over Sloping Foreshores
In hydraulic model tests, it is common practice to relate the response of the tested structure to the incident wave parameters at the toe. Estimation of the incident wave parameters at the toe is thus an essential part of the analysis of hydraulic model testing. In many cases, the design conditions at the toe are given by waves that are highly nonlinear or even depth limited. Modelling such conditions requires reproducing the prototype foreshore slope in the model. The present paper provide guidelines on the accuracy of a nonlinear reflection separation algorithm when applied to nonlinear waves over sloping foreshores. A simple methodology has been established to estimate the expected errors on the incident wave parameters.
- Open Access
- 25 April 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Generation Of Highly Nonlinear Waves In A Short Wave Flume
The typical approach for generating nonlinear waves in physical models involves employing first- or second-order wave theory, requiring a large water depth at the wavemaker. When the prototype bathymetry shows a gentle slope, a large facility is required. However, practical constraints often make this unfeasible, leading to the use of steep transition slopes to obtain sufficient water depth at the generator. Incorporating a transition slope may generate unwanted free waves beyond the transition point, significantly impacting the wave parameters. The presence of these free waves causes the response of the tested structure to deviate from that found in the prototype. This paper offers guidelines for using transition slopes effectively while avoiding the generation of undesired free waves after the transition point.
- 25 April 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Open AccessGeneration Of Highly Nonlinear Waves In A Short Wave Flume
The typical approach for generating nonlinear waves in physical models involves employing first- or second-order wave theory, requiring a large water depth at the wavemaker. When the prototype bathymetry shows a gentle slope, a large facility is required. However, practical constraints often make this unfeasible, leading to the use of steep transition slopes to obtain sufficient water depth at the generator. Incorporating a transition slope may generate unwanted free waves beyond the transition point, significantly impacting the wave parameters. The presence of these free waves causes the response of the tested structure to deviate from that found in the prototype. This paper offers guidelines for using transition slopes effectively while avoiding the generation of undesired free waves after the transition point.
- Open Access
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 8
THE VAN DER MEER FORMULA FOR ROCK SLOPE STABILITY AT SHALLOW WATER
In Van der Meer (2021) the stability formula for rock slopes under wave attack has been rewritten to remove the mean period Tm and to include the spectral period Tm-1,0. This formula is now identical to the Modified Van der Meer formula in the Rock Manual (2007 – Eqs 5.139 and 5.140), except for its coefficients and the use of H2 percent in the Rock Manual and H1/3 in Van der Meer (2021). A method has been given in Van der Meer (2021) by coefficients cpl and csu in the rewritten formula, to include (new) data on rock slope stability where results differ from the original formula and data. The re-fit of the shallow water data by Van Gent (2004) leading to the Modified Van der Meer formula for shallow water comes now to cpl=0.92 and csu=0.96, showing that rock slopes are less stable in shallow water than in deep water (coefficients smaller than 1 show less stability). The main objective is then: when and where do shallow water stability results deviate from the known stability formulae and how can we describe the deviating results. The original dataset by Van Gent (2004) and additional tests by Eldrup (2019) as well as other data have been analysed in depth to come to an improved understanding of rock slope stability in shallow water.
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 8
Open AccessTHE VAN DER MEER FORMULA FOR ROCK SLOPE STABILITY AT SHALLOW WATER
In Van der Meer (2021) the stability formula for rock slopes under wave attack has been rewritten to remove the mean period Tm and to include the spectral period Tm-1,0. This formula is now identical to the Modified Van der Meer formula in the Rock Manual (2007 – Eqs 5.139 and 5.140), except for its coefficients and the use of H2 percent in the Rock Manual and H1/3 in Van der Meer (2021). A method has been given in Van der Meer (2021) by coefficients cpl and csu in the rewritten formula, to include (new) data on rock slope stability where results differ from the original formula and data. The re-fit of the shallow water data by Van Gent (2004) leading to the Modified Van der Meer formula for shallow water comes now to cpl=0.92 and csu=0.96, showing that rock slopes are less stable in shallow water than in deep water (coefficients smaller than 1 show less stability). The main objective is then: when and where do shallow water stability results deviate from the known stability formulae and how can we describe the deviating results. The original dataset by Van Gent (2004) and additional tests by Eldrup (2019) as well as other data have been analysed in depth to come to an improved understanding of rock slope stability in shallow water.
- Open Access
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 38
INFLUENCE FACTORS FOR CREST WIDTH, ROUGHNESS AND WAVE PERIOD ON OVERTOPPING OF RUBBLE MOUND STRUCTURES
New data was collected in the wave flumes of Ghent University and Aalborg University on wave overtopping discharges over rubble mound structures, focusing on the influence of (large) crest width and surface roughness in combination with wave period. Combining these new data with existing data, analysis has led to the improvement of the guidance for wave overtopping prediction. The data and full analysis are presented in Eldrup et al. (2022). The present extended abstract adds a comparison of this improved guidance to the Neural Network prediction by Formentin et al. (2017), and to the EurOtop (2018) prediction.
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 38
Open AccessINFLUENCE FACTORS FOR CREST WIDTH, ROUGHNESS AND WAVE PERIOD ON OVERTOPPING OF RUBBLE MOUND STRUCTURES
New data was collected in the wave flumes of Ghent University and Aalborg University on wave overtopping discharges over rubble mound structures, focusing on the influence of (large) crest width and surface roughness in combination with wave period. Combining these new data with existing data, analysis has led to the improvement of the guidance for wave overtopping prediction. The data and full analysis are presented in Eldrup et al. (2022). The present extended abstract adds a comparison of this improved guidance to the Neural Network prediction by Formentin et al. (2017), and to the EurOtop (2018) prediction.
- Open Access
- 1 June 2022
- Published by Elsevier in Coastal Engineering
- Vol. 176
Improved guidance on roughness and crest width in overtopping of rubble mound structures along EurOtop
- 1 June 2022
- Published by Elsevier in Coastal Engineering
- Vol. 176
Open AccessImproved guidance on roughness and crest width in overtopping of rubble mound structures along EurOtop
- Open Access
- 1 October 2021
- Published by Elsevier in Coastal Engineering
- Vol. 169
Estimation of incident and reflected components in nonlinear regular waves over sloping foreshores
- 1 October 2021
- Published by Elsevier in Coastal Engineering
- Vol. 169
Open AccessEstimation of incident and reflected components in nonlinear regular waves over sloping foreshores
- 1 September 2021
- Published by Elsevier in Coastal Engineering
- Vol. 168
Advance in wave reflection estimation for rubble mound breakwaters: The importance of the relative water depth
- 1 September 2021
- Published by Elsevier in Coastal Engineering
- Vol. 168
Advance in wave reflection estimation for rubble mound breakwaters: The importance of the relative water depth
- Open Access
- 16 May 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (5) , 352
Wave Load Mitigation by Perforation of Monopiles
The design of large diameter monopiles (8–10 m) at intermediate to deep waters is largely driven by the fatigue limit state and mainly due to wave loads. The scope of the present paper is to assess the mitigation of wave loads on a monopile by perforation of the shell. The perforation design consists of elliptical holes in the vicinity of the splash zone. Wave loads are estimated for both regular and irregular waves through physical model tests in a wave flume. The test matrix includes waves with Keulegan–Carpenter ( ) numbers in the range 0.25 to 10 and covers both fatigue and ultimate limit states. Load reductions in the order of 6%–20% are found for numbers above 1.5. Significantly higher load reductions are found for numbers less than 1.5 and thus the potential to reduce fatigue wave loads has been demonstrated.- 16 May 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (5) , 352
Open AccessWave Load Mitigation by Perforation of Monopiles
The design of large diameter monopiles (8–10 m) at intermediate to deep waters is largely driven by the fatigue limit state and mainly due to wave loads. The scope of the present paper is to assess the mitigation of wave loads on a monopile by perforation of the shell. The perforation design consists of elliptical holes in the vicinity of the splash zone. Wave loads are estimated for both regular and irregular waves through physical model tests in a wave flume. The test matrix includes waves with Keulegan–Carpenter ( ) numbers in the range 0.25 to 10 and covers both fatigue and ultimate limit states. Load reductions in the order of 6%–20% are found for numbers above 1.5. Significantly higher load reductions are found for numbers less than 1.5 and thus the potential to reduce fatigue wave loads has been demonstrated.