Raju Ahamed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Raju Ahamed has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Dristy Parveg
VTT Technical Research Centre of Finland Ltd., Espoo, Finland
5 shared publications Kari A. I. Halonen
Department of Electronics and Nanoengineering, Aalto University, Espoo, Finland
5 shared publications- Mikko Varonen
VTT Technical Research Centre of Finland Ltd., Espoo, Finland
5 shared publications Jan Saijets
VTT Technical Research Centre of Finland Ltd, Espoo, Finland
2 shared publicationsMikko Kantanen
VTT Technical Research Centre of Finland Ltd., Espoo, Finland
2 shared publicationsNajmussadat
Department of Electronics and Nanoengineering, Aalto University, Espoo, Finland
2 shared publications
Latest Publications
- Open Access
- 6 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 23565-23577
220-240-GHz High-Gain Phase Shifter Chain and Power Amplifier for Scalable Large Phased-Arrays
This paper focuses on the design aspects of the key components for a scalable phased-array system over the 200 GHz frequency range. A high-gain phase shifter chain for 220 to 240 GHz frequency range and a high-gain power amplifier (PA) with a high output power are designed in a 0.13- $\mu \text{m}$ SiGe BiCMOS technology. The phase shifter chain includes a low-noise amplifier (LNA), a vector modulator phase shifter (PS), and a gain-enhancing amplifier. The LNA is a five-stage cascode design. The vector modulator core is realized by two variable gain amplifiers based on the Gilbert cell architecture. A four-stage cascode design is used for the gain-enhancing amplifier. The phase shifter chain shows a measured gain of 18 dB at 230 GHz with a $360 {\mathrm { ^{\circ}}}$ phase tuning range and more than 10 dB of gain control. The chip achieves a minimum measured noise figure of 11.5 dB at 230 GHz and shows a wideband noise characteristic. The complete phase shifter chain chip consumes a dc power of 153 mW and occupies a 1.41 mm2 area. A high-power PA that is critical for a large phased-array system is designed. This paper presents a unique 4-way power combining technique utilizing a differential quadrature coupler. The realized balanced PA occupies an area of 0.67 mm2 and shows a measured peak gain of 21 dB at 244 GHz. The PA consumes 819 mW of dc power and delivers a maximum saturated output power $(P_{sat})$ of 7.1 dBm at 244 GHz and more than 4.3 dBm of $P_{sat}$ from 230 to 255 GHz.
- 6 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 23565-23577
Open Access220-240-GHz High-Gain Phase Shifter Chain and Power Amplifier for Scalable Large Phased-Arrays
This paper focuses on the design aspects of the key components for a scalable phased-array system over the 200 GHz frequency range. A high-gain phase shifter chain for 220 to 240 GHz frequency range and a high-gain power amplifier (PA) with a high output power are designed in a 0.13- $\mu \text{m}$ SiGe BiCMOS technology. The phase shifter chain includes a low-noise amplifier (LNA), a vector modulator phase shifter (PS), and a gain-enhancing amplifier. The LNA is a five-stage cascode design. The vector modulator core is realized by two variable gain amplifiers based on the Gilbert cell architecture. A four-stage cascode design is used for the gain-enhancing amplifier. The phase shifter chain shows a measured gain of 18 dB at 230 GHz with a $360 {\mathrm { ^{\circ}}}$ phase tuning range and more than 10 dB of gain control. The chip achieves a minimum measured noise figure of 11.5 dB at 230 GHz and shows a wideband noise characteristic. The complete phase shifter chain chip consumes a dc power of 153 mW and occupies a 1.41 mm2 area. A high-power PA that is critical for a large phased-array system is designed. This paper presents a unique 4-way power combining technique utilizing a differential quadrature coupler. The realized balanced PA occupies an area of 0.67 mm2 and shows a measured peak gain of 21 dB at 244 GHz. The PA consumes 819 mW of dc power and delivers a maximum saturated output power $(P_{sat})$ of 7.1 dBm at 244 GHz and more than 4.3 dBm of $P_{sat}$ from 230 to 255 GHz.
- 17 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (7) , 883-886
A 200–250-GHz Phase Shifter Utilizing a Compact and Wideband Differential Quadrature Coupler
This letter presents the design of a 200–250-GHz compact vector modulator (VM) phase shifter in a 0.13- $\mu \text{m}$ SiGe bipolar complementary metal-oxide-semiconductor (BiCMOS) technology. A compact, low-loss, and wideband differential quadrature coupler is used to generate differential I/Q signals. The design details of the millimeter-wave wideband differential coupler is presented and compared with other I/Q generators by the 3-D electromagnetic (EM)-simulated results. The VM core is realized by two variable gain amplifiers based on Gilbert cell architecture. The measured phase shifter shows a gain of −10.3 dB for the maximum gain setting at 230 GHz. The phase shifter shows a −17 dB of gain for full 360° phase tuning range and a 10 dB of gain control. The maximum rms gain error and the phase error are 1.25 dB and 10°, respectively, from 200 to 250 GHz. The chip consumes a dc power of 55 mW and occupies a core area of 0.09 mm 2 .
- 17 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (7) , 883-886
A 200–250-GHz Phase Shifter Utilizing a Compact and Wideband Differential Quadrature Coupler
This letter presents the design of a 200–250-GHz compact vector modulator (VM) phase shifter in a 0.13- $\mu \text{m}$ SiGe bipolar complementary metal-oxide-semiconductor (BiCMOS) technology. A compact, low-loss, and wideband differential quadrature coupler is used to generate differential I/Q signals. The design details of the millimeter-wave wideband differential coupler is presented and compared with other I/Q generators by the 3-D electromagnetic (EM)-simulated results. The VM core is realized by two variable gain amplifiers based on Gilbert cell architecture. The measured phase shifter shows a gain of −10.3 dB for the maximum gain setting at 230 GHz. The phase shifter shows a −17 dB of gain for full 360° phase tuning range and a 10 dB of gain control. The maximum rms gain error and the phase error are 1.25 dB and 10°, respectively, from 200 to 250 GHz. The chip consumes a dc power of 55 mW and occupies a core area of 0.09 mm 2 .
- 9 July 2018
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 98 (3) , 465-476
A 71–76 GHz wideband receiver front-end for phased array applications in 0.13 μm SiGe BiCMOS technology
- 9 July 2018
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 98 (3) , 465-476
A 71–76 GHz wideband receiver front-end for phased array applications in 0.13 μm SiGe BiCMOS technology
- 1 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 145-148
Design of an E-band Doherty Power amplifier
This paper demonstrates the design of an E-band Doherty power amplifier (PA) based in an 130nm SiGe BiCMOS process. This design includes main and auxiliary amplifiers, lange coupler and a pre-amplifier. The designed power amplifier exhibits a saturated output power of 14.4 dBm and output referred P1dB of 11.7 dBm. The peak power added efficiency (PAE) of this amplifier is 19.2%. This PA shows PAE of 17% at P1dB and 11.6% at 6-dB output power back off. The peak power gain of this Doherty PA is 23 dB at 75 GHz with a 3-dB bandwidth from 60 to 80 GHz. The designed Doherty PA consumes DC power of 52 mW with a chip area of 900 μm × 800 μm without RF pads.
- 1 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 145-148
Design of an E-band Doherty Power amplifier
This paper demonstrates the design of an E-band Doherty power amplifier (PA) based in an 130nm SiGe BiCMOS process. This design includes main and auxiliary amplifiers, lange coupler and a pre-amplifier. The designed power amplifier exhibits a saturated output power of 14.4 dBm and output referred P1dB of 11.7 dBm. The peak power added efficiency (PAE) of this amplifier is 19.2%. This PA shows PAE of 17% at P1dB and 11.6% at 6-dB output power back off. The peak power gain of this Doherty PA is 23 dB at 75 GHz with a 3-dB bandwidth from 60 to 80 GHz. The designed Doherty PA consumes DC power of 52 mW with a chip area of 900 μm × 800 μm without RF pads.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Design of high-performance E-band SPDT switch and LNA in 0.13 μm SiGe BiCMOS technology
This paper presents the design of high-performance E-band single-pole double-through (SPDT) switch and low noise amplifier (LNA) as a part of transceiver front-end in an 0.13 μm SiGe BiCMOS technology. The quarter-wave shunt SPDT switch is designed using reverse-saturated SiGe HBTs. The resulting switch exhibits an insertion loss of 2.1 dB, isolation of 26 dB, reflection coefficient better than 18 dB at 75 GHz and provides a bandwidth of more than 35 GHz. The designed switch is integrated with a single-in differential-output (SIDO) low noise amplifier (LNA) and utilized as input matching element of the LNA. The LNA utilizes a common-emitter amplifier at the first stage and a casocode amplifier at the second stage to exploit the advantages of both common-emitter and cascode topologies. The resulting LNA with integrated switch achieves a gain and noise figure(NF) of 26 dB and 6.9 dB, respectively at 75 GHz with a 3 dB bandwidth of 12 GHz. Output referred 1-dB compression point of +5.5 dBm is achieved at 75 GHz. The designed integrated block consumes 45.5 mW of DC power and occupies an area of 720 μm × 580 μm excluding RF pads.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Design of high-performance E-band SPDT switch and LNA in 0.13 μm SiGe BiCMOS technology
This paper presents the design of high-performance E-band single-pole double-through (SPDT) switch and low noise amplifier (LNA) as a part of transceiver front-end in an 0.13 μm SiGe BiCMOS technology. The quarter-wave shunt SPDT switch is designed using reverse-saturated SiGe HBTs. The resulting switch exhibits an insertion loss of 2.1 dB, isolation of 26 dB, reflection coefficient better than 18 dB at 75 GHz and provides a bandwidth of more than 35 GHz. The designed switch is integrated with a single-in differential-output (SIDO) low noise amplifier (LNA) and utilized as input matching element of the LNA. The LNA utilizes a common-emitter amplifier at the first stage and a casocode amplifier at the second stage to exploit the advantages of both common-emitter and cascode topologies. The resulting LNA with integrated switch achieves a gain and noise figure(NF) of 26 dB and 6.9 dB, respectively at 75 GHz with a 3 dB bandwidth of 12 GHz. Output referred 1-dB compression point of +5.5 dBm is achieved at 75 GHz. The designed integrated block consumes 45.5 mW of DC power and occupies an area of 720 μm × 580 μm excluding RF pads.