Herbert Scheerer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Herbert Scheerer has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Matthias Oechsner
Technical University of Darmstadt, Darmstadt, Germany
2 shared publications C. Berger
Institut für Werkstoffkunde, Fachgebiet Maschinenbau, Technische Universität Darmstadt, Grafenstraße 2, 64283 Darmstadt
1 shared publicationChristina Berger
Institute of Materials Technology, Grafenstr. 2, 64283 Darmstadt, Germany
1 shared publicationD. Hellmann
KSB AG Johann-Klein-Straße 9 67227 FRANKENTHAL GERMANY
1 shared publicationDieter Hellmann
KSB Frankenthal (Pfalz) 67227 Germany
1 shared publicationEberhard Abele
Institute of Production Management, Technology and Machine Tools, Petersenstr. 30, 64287 Darmstadt, Germany
1 shared publication
Latest Publications
- 10 December 2018
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 49 (12) , 1423-1438
Tribo‐chemical smoothening process with silica nanoparticles
Additional silica (silicon dioxide) nanoparticles were added in the tribo‐gap to prevent the severe abrasive wear. The method was a flat surface‐contact reciprocating sliding test between the sintered silicon carbide surfaces with water lubrication. Before testing, the silica nanoparticles were added in the tribo‐gap. These silica nanoparticles acted as a buffer layer during the initial running‐in, thus the abrasion risk was decreased. After running‐in, the silicon carbide surface was tribo‐chemically smoothened without severe abrasion. Comparing to the same tests without silica nanoparticles, the same ultra‐low friction state (friction coefficient was approx. 0.01) was built, and the running‐in period was shortened by 80 %. As has been well reported, the tribo‐chemical smoothening process for silicon carbide needs abundant water, e. g., in the point‐contact tests. However, in the surface‐contact case, water is locally insufficient, which induces severe wear. The preset silica nanoparticles can solve this wear problem. Therefore, it is not necessary to polish the silicon carbide surfaces as the seal faces in mechanical seals. Instead, a pair of rough silicon carbide surfaces can be pressed onto each other and then proceed to a running‐in with preset silica nanoparticles. After running‐in, a pair of precisely mated tribo‐chemically smoothened surfaces can be naturally obtained.
- 10 December 2018
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 49 (12) , 1423-1438
Tribo‐chemical smoothening process with silica nanoparticles
Additional silica (silicon dioxide) nanoparticles were added in the tribo‐gap to prevent the severe abrasive wear. The method was a flat surface‐contact reciprocating sliding test between the sintered silicon carbide surfaces with water lubrication. Before testing, the silica nanoparticles were added in the tribo‐gap. These silica nanoparticles acted as a buffer layer during the initial running‐in, thus the abrasion risk was decreased. After running‐in, the silicon carbide surface was tribo‐chemically smoothened without severe abrasion. Comparing to the same tests without silica nanoparticles, the same ultra‐low friction state (friction coefficient was approx. 0.01) was built, and the running‐in period was shortened by 80 %. As has been well reported, the tribo‐chemical smoothening process for silicon carbide needs abundant water, e. g., in the point‐contact tests. However, in the surface‐contact case, water is locally insufficient, which induces severe wear. The preset silica nanoparticles can solve this wear problem. Therefore, it is not necessary to polish the silicon carbide surfaces as the seal faces in mechanical seals. Instead, a pair of rough silicon carbide surfaces can be pressed onto each other and then proceed to a running‐in with preset silica nanoparticles. After running‐in, a pair of precisely mated tribo‐chemically smoothened surfaces can be naturally obtained.
- Open Access
- 5 December 2018
- Published by Tsinghua University Press in Friction
- Vol. 7 (2) , 181-191
Experimental study on the tribo-chemical smoothening process between self-mated silicon carbide in a water-lubricated surface-contact reciprocating test
Silicon carbide (SiC) can be tribo-chemically smoothened during a self-mated sliding procedure in the aqueous environment. As well reported in the point-contact tests, this smoothening process works well due to the abundant water as oxidant. After this smoothening process, the tribo-surface is well polished, a closely mated tribo-gap naturally forms, and an ultra-low friction state is built. However, water in the tribo-gap could be insufficient in industrial applications, e.g., the seal gap in mechanical seals. In this study, the tribo-chemical smoothening behavior in such environment was researched. A surface-contact reciprocating test was used to simulate the aqueous environment where water was insufficient. After tests, compared to the published results from the point-contact tests, the same ultra-low friction state was achieved. A part of the tribo-surface was tribo-chemically smoothened. The obtained smoothened surface microstructure was consistent with the published information. Meanwhile, severe abrasive wear occurred. A porous oxygen-rich layer was found existing beneath the abrasion-induced grooves, in which numerous smashed wear debris adhered on the worn surfaces. We concluded that the shortage of water initiated the severe abrasion, meanwhile the generated wear debris aggravated the wear condition. This understanding is instructive for developing new methods to avoid the severe abrasion in the same water insufficient environment.
- 5 December 2018
- Published by Tsinghua University Press in Friction
- Vol. 7 (2) , 181-191
Open AccessExperimental study on the tribo-chemical smoothening process between self-mated silicon carbide in a water-lubricated surface-contact reciprocating test
Silicon carbide (SiC) can be tribo-chemically smoothened during a self-mated sliding procedure in the aqueous environment. As well reported in the point-contact tests, this smoothening process works well due to the abundant water as oxidant. After this smoothening process, the tribo-surface is well polished, a closely mated tribo-gap naturally forms, and an ultra-low friction state is built. However, water in the tribo-gap could be insufficient in industrial applications, e.g., the seal gap in mechanical seals. In this study, the tribo-chemical smoothening behavior in such environment was researched. A surface-contact reciprocating test was used to simulate the aqueous environment where water was insufficient. After tests, compared to the published results from the point-contact tests, the same ultra-low friction state was achieved. A part of the tribo-surface was tribo-chemically smoothened. The obtained smoothened surface microstructure was consistent with the published information. Meanwhile, severe abrasive wear occurred. A porous oxygen-rich layer was found existing beneath the abrasion-induced grooves, in which numerous smashed wear debris adhered on the worn surfaces. We concluded that the shortage of water initiated the severe abrasion, meanwhile the generated wear debris aggravated the wear condition. This understanding is instructive for developing new methods to avoid the severe abrasion in the same water insufficient environment.
- 1 April 2007
- Published by Wiley in Plasma Processes and Polymers
- Vol. 4 (S1) , S622-S627
Dry Machining Using CrAlYN Coated Carbides
- 1 April 2007
- Published by Wiley in Plasma Processes and Polymers
- Vol. 4 (S1) , S622-S627
Dry Machining Using CrAlYN Coated Carbides
- 21 February 2006
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 37 (2) , 183-190
Untersuchungen zur Wälzermüdung nach induktivem Kurzzeitanlassen
- 21 February 2006
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 37 (2) , 183-190
Untersuchungen zur Wälzermüdung nach induktivem Kurzzeitanlassen