TSTatyana G. Shikova

Tatyana G. Shikova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tatyana G. Shikova has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Кинетические закономерности плазмохимического модифицирования поливинилиденфторидa в плазме

    by Т. Г. Шикова, И. B. Холодков, С. А. Смирнов, Б. Л. Горберг, М. О. Макеев, П. A. Михалев, А. С. Осипков

    Кинетические закономерности плазмохимического модифицирования поливинилиденфторидa в плазме Кинетические закономерности плазмохимического модифицирования поливинилиденфторидa в плазме

  • Kinetic Features of Plasma-Chemical Modification of Polyvinylidene Fluoride in Plasma

    by T. G. Shikova, I. V. Kholodkov, S. A. Smirnov, B. L. Gorberg, M. O. Makeev, P. A. Mikhalev, A. S. Osipkov

    Changes in the composition of the surface layer of Nevaflon polyvinylidene fluoride film after treatment in gas discharges of various types (glow, dielectric barrier, corona) have been studied. The influence of the discharge type on the kinetics of etching and surface modification of polyvinylidene fluoride is shown. It has been found that the plasma treatment of polyvinylidene fluoride leads to a change in the modified surface layer of the polymer.


  • Open Access

    Applicability of Electron-Beam and Hybrid Plasmas for Polyethylene Terephthalate Processing to Obtain Hydrophilic and Biocompatible Surfaces

    by Tatiana Vasilieva, Elena Nikolskaya, Michael Vasiliev, Mariia Mollaeva, Margarita Chirkina, Maria Sokol, Nikita Yabbarov, Tatiana Shikova, Artem Abramov, Aleksandr Ugryumov

    The applicability of beam-plasma chemical reactors generating cold hybrid plasma for the production of noncytotoxic polymeric surfaces with high hydrophilicity and good biocompatibility with human fibroblast culture and human red blood cells was studied. Oxygen hybrid plasma was excited by the joint action of a continuous scanning electron beam and a capacity-coupled RF-gas discharge. Experiments showed that hybrid plasma treatment caused polar oxygen-containing functional group formation in the surface layer of poly (ethylene terephthalate) films. No thermal or radiative damage in tested polymer samples was found. The plasma-modified polymers turned out to be noncytotoxic and revealed good biocompatibility with human fibroblasts BJ-5ta as well as lower hemolytic activity than untreated poly (ethylene terephthalate). Experiments also demonstrated that no phenomena caused by the electrostatic charging of polymers occur in hybrid plasma because the electron beam component of hybrid plasma eliminates the item charge when it is treated. The electron beam can effectively control the reaction volume geometry as well as the fluxes of active plasma particles falling on the item surface. This provides new approaches to the production of abruptly structured patterns or smooth gradients of functionalities on a plane and 3D polymeric items of complicated geometry.


  • KINETIC FEATURES OF PLASMA-CHEMICAL MODIFICATION OF POLYCARBONATE IN PLASMA IN ARGON - OXYGEN MIXTURE

    by Tatyana G. Shikova, Sergey A. Smirnov, Alexey I. Artyuhov

    В работе приводятся результаты экспериментальных исследований процессов деструкции и изменения состава поверхностного слоя плёнки поликарбоната (ПК) марки Lexan 8010 при обработке в положительном столбе тлеющего разряда постоянного тока в аргоне, кислороде и их смесях. Измерены скорости убыли массы образцов в зависимости от параметров разряда и состава плазмообразующего газа, проанализированы ИК спектры НПВО пленок полимера после воздействия плазмы. Показано, что наиболее заметные изменения в скорости деструкции образца и химическом составе поверхностного слоя происходят при содержании кислорода в смеси до 20%. При дальнейшем увеличении содержания О2 в плазмообразующей смеси изменения незначительны. Основными газообразными продуктами деструкции ПК в плазме смеси аргон-кислород являются H2, CO и H2O. В первую секунду после включения разряда с максимальной скоростью выделяются молекулы Н2 и с меньшей скоростью CO. Образование молекул окиси углерода и водорода происходит без непосредственного участия кислорода под действием активных частиц плазмы аргона без участия активного кислорода. Воздействие плазмы аргона приводит к росту содержания кислорода на поверхности образца. При этом наблюдается разрушение связей С–О, О–С(=О)–О, являющихся частью структуры элементарного звена поликарбоната, и образование новых кислородсодержащих связей. Травление полимера активными частицами плазмы приводит к изменению микрорельефа поверхности образца. Изменение шероховатости, рост концентрации полярных функциональных групп приводит к увеличению смачиваемости поверхности пленки ПК. Проведено обсуждение возможных механизмов процессов, позволяющее описать наблюдаемые результаты.

  • Open Access

    The Influence of DC discharge afterglow treatment on poly(ethylene terephthalate) surface properties

    by D P Vasilkin, T G Shikova, S A Smirnov, D I Nikitin

    In this work, we investigated the effects of gas flow rate, processing time and distance from plasma region on the modification of poly(ethylene terephthalate) (PET) films under conditions of afterglows of atmospheric pressure discharges in air and argon. Both original and plasma-modified surfaces were studied by FTIR, AFM, XPS and contact angle measurements. It was found that the remote treatment 1) results in increasing PET surface hydrophilicity, but in decreasing contact angles (by ∼ 3 times compared with the original sample); 2) leads to the destruction of ester groups as well as to the formation of new C-O groups; and 3) causes an increase in average surface roughness (from 1.4 nm for untreated PET to 2.2 and 4.4 nm for PET modified by air and argon afterglows, respectively). The set of experimental techniques together with plasma modeling provided the information on plasma emission properties, gas temperature, reduced electric field strength, discharge geometry and densities of plasma active species. Based on these data, the modification mechanism involving UV photons and O atoms was proposed.

  • GAS PRODUCTS OF ARGON PLASMA INTERACTION WITH POLYARAMID AND POLY(ETHYLENE TEREPHTHALATE)

    by Valeriy A. Titov, Tatyana G. Shikova, Sergey A. Smirnov, Alexander A. Ovtsyn, Lyudmila A. Kuzmicheva, Anna V. Khlustova

    Non-equilibrium plasma is widely used for surface modification of polymer materials. Reactions of plasma active species with polymers lead not only to the surface modification, but to the formation of gaseous products, which change the plasma composition and internal plasma parameters. It results in the dependence of surface etching and modification kinetics on the quantity of material been treated (on sample sizes in a reactor). These phenomena are known as so called “loading effect” and have been studied for the treatment of polypropylene and polyimide films, poly(ethylene terephthalate) films and fabrics in oxygen and air plasma. It can be expected that gas products of noble gas plasma action on polymers will change strongly plasma parameters and modification results. In this paper, experimental data are represented on composition of gas products and their evolution rates at the treatment of polyaramid films, fibers and poly(ethylene terephthalate) fabric in low-pressure argon plasma. Poly(ethylene terephthalate) textile fabric (PET) made of monofilament yarns (SAATI, S.p.A., Italy) and polyaramide (PA) films and complex yarns “Rusar®” (Termotex, Russia) were used in experiments. Direct current discharge was excited in a flow of argon (technical grade) in a glass tube reactor with 3 cm inner diameter. Fabric samples were placed as cylinders on the reactor wall in the discharge positive column. Square of PET samples was varied from 18 to 111 cm2. The PA yarns with the total length of 550 or 1020 cm were placed in the reactor on special holder with the length of 20 cm. Total gas pressure in reactor was varied from 30 to 300 Pa at discharge current of 20 – 110 mA. Gas flow rate in the reactor was kept constant and equal to 30 cm´s-1. Gas phase analysis was carried out by the methods of plasma emission spectroscopy and mass-spectrometry. Plasma emission spectra and mass-spectra show evolution of H2, CO and H2O molecules at the treatment of PA and PET in argon plasma. Evolution rates for different gas products and their mole fractions have been obtained as functions of total gas pressure. Increase in polymer sample square has been shown to result in changing the ratios between evolution rates for different gas products. Sum of CO, H2 and H2O mole fractions increases with polymer sample square and decreases with gas pressure. Dissociation of molecular gas products results in the changing plasma active species. Oxygen and hydrogen atom lines and OH emission bands are observed in plasma emission spectra. Alteration of intensity ratio for О(3p3P ® 3s3S0) and Ar (4p3D3 ® 4s3P2) lines (IO/IAr) versus time after discharge starting shows the possible participation of oxygen atoms in heterogeneous reactions with polymers. Evolution of molecular gas products of heterogeneous reactions influences plasma properties and rates of plasma chemical reactions. The data obtained will be used for the further analysis of mechanisms of heterogeneous reactions of plasma active species with polymers.