Tomas Soria Biurrun
Research Subjects
Tomas Soria Biurrun has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Anne Vornberger
Fraunhofer IKTS, Fraunhofer Institute for Ceramic Technologies and Systems, 01277 Dresden, Germany
2 shared publications - Johannes Pötschke
Fraunhofer IKTS, Fraunhofer Institute for Ceramic Technologies and Systems, 01277 Dresden, Germany
2 shared publications - Angela Serpe
Department of Civil and Environmental Engineering and Architecture (DICAAR), and Research Unit of INSTM, University of Cagliari, Via Marengo 2, 09123 Cagliari, Italy
1 shared publication - Belen Lopez Ezquerra1 shared publication
- Federico Ibarreta Lopez1 shared publication
Fraunhofer Ikts Dresden
1 shared publication
Latest Publications
- 11 October 2026
- Published by European Powder Metallurgy Association
Properties Of Hardmetals From Reclaimed WC-Co Powders Produced By Different Recycling Methods
Circularity is vital in production of WC-Co hardmetals to reduce tungsten supply risk and environmental burdens. This study within the EU Horizon RESQTOOL-project compares hardmetals made from reclaimed WC-Co powders produced by two routes, zinc reclaim and oxidation-reduction, against a virgin powder reference. The study includes characterization of powder properties, investigation of different milling conditions and resulting compaction behavior. Sintered parts were evaluated in regard to density, magnetic parameters, hardness, and fracture toughness. Furthermore, thermogravimetry and dilatometry was used to investigate the sintering behavior. The results provide a basis to evaluate the potential of recycled WC-Co powders and add to the understanding of sustainable manufacturing.
- 11 October 2026
- Published by European Powder Metallurgy Association
Properties Of Hardmetals From Reclaimed WC-Co Powders Produced By Different Recycling Methods
Circularity is vital in production of WC-Co hardmetals to reduce tungsten supply risk and environmental burdens. This study within the EU Horizon RESQTOOL-project compares hardmetals made from reclaimed WC-Co powders produced by two routes, zinc reclaim and oxidation-reduction, against a virgin powder reference. The study includes characterization of powder properties, investigation of different milling conditions and resulting compaction behavior. Sintered parts were evaluated in regard to density, magnetic parameters, hardness, and fracture toughness. Furthermore, thermogravimetry and dilatometry was used to investigate the sintering behavior. The results provide a basis to evaluate the potential of recycled WC-Co powders and add to the understanding of sustainable manufacturing.
- Open Access
- 1 July 2026
- Published by Elsevier in SSRN Electronic Journal
Comparison of the shrinkage behavior of virgin and recycled WC-Co submicron powders during liquid phase sintering
Sintering shrinkage in recycled WC–Co hardmetal alloys has been investigated for two recycling routes: zinc reclaim and oxidation–reduction–carburization (ORC) and compared with virgin reference materials. Recycled powders are strongly agglomerated and exhibit significantly lower specific surface areas, making milling essential to enhance sinterability. Two stages are identified during solid-state sintering: up to 1000 ºC, densification is controlled by oxide content and specific surface area, while lattice strain plays a minor role. At higher temperatures, solid-state shrinkage kinetics become similar for virgin and recycled materials due to defect annealing and reduced surface area. Liquid-phase formation accelerates densification in virgin alloys, whereas an opposite trend is observed in recycled powders—especially ORC—due to a shift of solid-state diffusion to higher temperatures, which promotes overlap with liquid-phase rearrangement and solution–reprecipitation processes.
- 1 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessComparison of the shrinkage behavior of virgin and recycled WC-Co submicron powders during liquid phase sintering
Sintering shrinkage in recycled WC–Co hardmetal alloys has been investigated for two recycling routes: zinc reclaim and oxidation–reduction–carburization (ORC) and compared with virgin reference materials. Recycled powders are strongly agglomerated and exhibit significantly lower specific surface areas, making milling essential to enhance sinterability. Two stages are identified during solid-state sintering: up to 1000 ºC, densification is controlled by oxide content and specific surface area, while lattice strain plays a minor role. At higher temperatures, solid-state shrinkage kinetics become similar for virgin and recycled materials due to defect annealing and reduced surface area. Liquid-phase formation accelerates densification in virgin alloys, whereas an opposite trend is observed in recycled powders—especially ORC—due to a shift of solid-state diffusion to higher temperatures, which promotes overlap with liquid-phase rearrangement and solution–reprecipitation processes.
- 1 December 2018
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 77, 44-53
Sintering of WC hardmetals with Ni-Co-Cr-Ti-Al multi-component alloys
- 1 December 2018
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 77, 44-53
Sintering of WC hardmetals with Ni-Co-Cr-Ti-Al multi-component alloys