Shijun Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shijun Sun has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Jianhua Wang
4 shared publications- Yanming Liu
School of Aerospace Engineering, Beijing Institute of Technology, Beijing, 100081, China
3 shared publications Songtao Wang
2 shared publicationsXiaolong Li
2 shared publicationsYanming Liu
2 shared publicationsCe Yang
1 shared publication
Latest Publications
- 1 November 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (11)
Evolution of secondary flow structures and loss mechanisms in a mixed-flow compressor under high-altitude low-Reynolds-number conditions
To clarify performance deterioration of mixed-flow compressors under high-altitude low-Reynolds-number conditions, a highly loaded mixed-flow compressor rotor is investigated by three-dimensional numerical simulations at altitudes of 0, 11, 15, and 20 km. The results show that, as the inlet Reynolds number decreases, the efficiency and total pressure ratio characteristics shift toward lower corrected mass flow rate, lower efficiency, and lower total pressure ratio. At the peak-efficiency operating points, the adiabatic efficiency at 20 km decreases by 4.2 percentage points, while the total pressure ratio decreases by 10.1%, compared with their corresponding values at 0 km. The loss mainly originates from two near-tip flow structures: the tip leakage vortex (TLV) on the splitter-blade suction side, formed by secondary leakage from the main-blade tip clearance, and the casing passage vortex (CPV) in the main-blade suction-side passage, formed by low-energy fluid migrating radially from the main-blade leading-edge separation region and then moving circumferentially near the casing. As the Reynolds number decreases, the tip leakage flow increases, raising the TLV loss. Meanwhile, delayed separation-induced transition moves the reattachment position downstream and enlarges the leading-edge separation region. More low-energy fluid is then involved in radial migration, which promotes CPV development and increases the main-blade suction-side passage loss. The streamwise-averaged normalized entropy-increase flux shows that TLV loss dominates at 0 km, whereas CPV loss exceeds TLV loss from 11 km onward and becomes the main loss source with increasing altitude.
- 1 November 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (11)
Evolution of secondary flow structures and loss mechanisms in a mixed-flow compressor under high-altitude low-Reynolds-number conditions
To clarify performance deterioration of mixed-flow compressors under high-altitude low-Reynolds-number conditions, a highly loaded mixed-flow compressor rotor is investigated by three-dimensional numerical simulations at altitudes of 0, 11, 15, and 20 km. The results show that, as the inlet Reynolds number decreases, the efficiency and total pressure ratio characteristics shift toward lower corrected mass flow rate, lower efficiency, and lower total pressure ratio. At the peak-efficiency operating points, the adiabatic efficiency at 20 km decreases by 4.2 percentage points, while the total pressure ratio decreases by 10.1%, compared with their corresponding values at 0 km. The loss mainly originates from two near-tip flow structures: the tip leakage vortex (TLV) on the splitter-blade suction side, formed by secondary leakage from the main-blade tip clearance, and the casing passage vortex (CPV) in the main-blade suction-side passage, formed by low-energy fluid migrating radially from the main-blade leading-edge separation region and then moving circumferentially near the casing. As the Reynolds number decreases, the tip leakage flow increases, raising the TLV loss. Meanwhile, delayed separation-induced transition moves the reattachment position downstream and enlarges the leading-edge separation region. More low-energy fluid is then involved in radial migration, which promotes CPV development and increases the main-blade suction-side passage loss. The streamwise-averaged normalized entropy-increase flux shows that TLV loss dominates at 0 km, whereas CPV loss exceeds TLV loss from 11 km onward and becomes the main loss source with increasing altitude.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Aerodynamic performance response due to stagger angle variation in an axial supersonic through-flow fan blade
To enable a broader operational speed range in axial supersonic through-flow fans, this study investigates the effects of stagger angle variation (Δγ) using an adjustable cascade configuration. A comprehensive numerical study, covering a wide range of inlet Mach numbers from subsonic to supersonic regimes, was conducted to assess how Δγ affects aerodynamic performance and flow structure. A framework for entropy generation analysis based on dissipative sub terms was proposed, quantifying aerodynamic losses and elucidating potential flow physics. The results show that at design incidence, Δγ has a pronounced effect on the loss coefficient (ω), static pressure ratio (π), and flow turning angle (zw), particularly under transonic inflow conditions, with changes relative to Δγ = 0° reaching 168.2%, 216.9%, and 115.4%, respectively. Under subsonic conditions, the enhanced streamwise adverse pressure gradient at higher Δγ thickens the boundary layer, which elevates wall-normal shear. This makes (∂w/∂y)2 the dominant dissipation mechanism governing loss behavior. In supersonic flows, the loss increase is mainly driven by intensified oblique shock, which enhance streamwise shear and entropy generation. In contrast, the contribution of wall-normal shear dissipation remains relatively insensitive to Δγ variations. At off-design incidence, critical Δγ thresholds are identified at which losses surge significantly. For M = 0.60 and i = −3°, reducing Δγ from −4° to −8° induces a quasi-normal shock within the passage. Similarly, for M = 1.00 and unique incidence, as the Δγ increases from 4° to 8°, the trailing-edge shock transforms into a λ shock. Both of these shock evolutions cause increased shock and viscous losses.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Aerodynamic performance response due to stagger angle variation in an axial supersonic through-flow fan blade
To enable a broader operational speed range in axial supersonic through-flow fans, this study investigates the effects of stagger angle variation (Δγ) using an adjustable cascade configuration. A comprehensive numerical study, covering a wide range of inlet Mach numbers from subsonic to supersonic regimes, was conducted to assess how Δγ affects aerodynamic performance and flow structure. A framework for entropy generation analysis based on dissipative sub terms was proposed, quantifying aerodynamic losses and elucidating potential flow physics. The results show that at design incidence, Δγ has a pronounced effect on the loss coefficient (ω), static pressure ratio (π), and flow turning angle (zw), particularly under transonic inflow conditions, with changes relative to Δγ = 0° reaching 168.2%, 216.9%, and 115.4%, respectively. Under subsonic conditions, the enhanced streamwise adverse pressure gradient at higher Δγ thickens the boundary layer, which elevates wall-normal shear. This makes (∂w/∂y)2 the dominant dissipation mechanism governing loss behavior. In supersonic flows, the loss increase is mainly driven by intensified oblique shock, which enhance streamwise shear and entropy generation. In contrast, the contribution of wall-normal shear dissipation remains relatively insensitive to Δγ variations. At off-design incidence, critical Δγ thresholds are identified at which losses surge significantly. For M = 0.60 and i = −3°, reducing Δγ from −4° to −8° induces a quasi-normal shock within the passage. Similarly, for M = 1.00 and unique incidence, as the Δγ increases from 4° to 8°, the trailing-edge shock transforms into a λ shock. Both of these shock evolutions cause increased shock and viscous losses.
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Investigation of modal evolution and flow instability characteristics during radial diffuser stall in high-load centrifugal compressor with a throttle model
In high-load centrifugal compressors, radial diffusers are particularly susceptible to flow instability, which significantly restricts the stable operating range. This paper investigates the three-dimensional flow-field evolution in the radial diffuser from near stall to stable stall using full-annulus transient numerical simulations coupled with a throttle model. The results reveal that the most pronounced flow instability occurs in the vaneless and semi-vaneless (VLSV) regions of the radial diffuser, which evolve through three stages: near stall (S1), stall development (S2), and stable stall (S3). During this process, the dominant unstable region shifts from the vaneless section to the semi-vaneless section on the casing side of the diffuser. Through dynamic mode decomposition (DMD), the dominant mechanisms of each stage of unstable evolution are analyzed. The stall frequency increases from 396.3 Hz (0.41RF) in S2 to 684.2 Hz (0.7RF) in S3, with the corresponding energy contribution rising from 5.1% to 11.3%. Notably, in S3, the energy of low-frequency modes (1.4 RF, 2.1 RF, etc.) is significantly accumulated, accounting for 94.5% of the total, highlighting the critical role of low-frequency mode energy accumulation in diffuser instability. Further analysis reveals that in S1, unsteadiness is primarily driven by rotor–stator interactions dominated by the blade passing frequency between the impeller and diffuser. In S2, boundary layer separation caused by the interaction between the inlet shock wave and the boundary layer becomes the primary instability mechanism. In S3, the separated flow evolves into separation vortex structures, forming a blockage zone near the casing and ultimately inducing stable stall.
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Investigation of modal evolution and flow instability characteristics during radial diffuser stall in high-load centrifugal compressor with a throttle model
In high-load centrifugal compressors, radial diffusers are particularly susceptible to flow instability, which significantly restricts the stable operating range. This paper investigates the three-dimensional flow-field evolution in the radial diffuser from near stall to stable stall using full-annulus transient numerical simulations coupled with a throttle model. The results reveal that the most pronounced flow instability occurs in the vaneless and semi-vaneless (VLSV) regions of the radial diffuser, which evolve through three stages: near stall (S1), stall development (S2), and stable stall (S3). During this process, the dominant unstable region shifts from the vaneless section to the semi-vaneless section on the casing side of the diffuser. Through dynamic mode decomposition (DMD), the dominant mechanisms of each stage of unstable evolution are analyzed. The stall frequency increases from 396.3 Hz (0.41RF) in S2 to 684.2 Hz (0.7RF) in S3, with the corresponding energy contribution rising from 5.1% to 11.3%. Notably, in S3, the energy of low-frequency modes (1.4 RF, 2.1 RF, etc.) is significantly accumulated, accounting for 94.5% of the total, highlighting the critical role of low-frequency mode energy accumulation in diffuser instability. Further analysis reveals that in S1, unsteadiness is primarily driven by rotor–stator interactions dominated by the blade passing frequency between the impeller and diffuser. In S2, boundary layer separation caused by the interaction between the inlet shock wave and the boundary layer becomes the primary instability mechanism. In S3, the separated flow evolves into separation vortex structures, forming a blockage zone near the casing and ultimately inducing stable stall.
- 1 March 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (3)
Effect of blade–row axial spacing on the stage performance of an axial supersonic through-flow fan
Rotor–stator interaction has a large impact on the performance of axial compressors. Previous studies have suggested that less blade–row axial spacing (δz) of an axial flow compressor is associated with improved efficiency. However, these studies primarily focused on the subsonic-axial turbomachinery. The impact of δz on the performance in an axial supersonic through-flow fan (STFF) stage remains unclear. This study explores the effect of axial spacing on the performance of an STFF stage using unsteady numerical simulations. The results show that both the total pressure ratio and adiabatic efficiency are reduced when axial spacing changes from δz = 1.0 regardless of whether it increases or decreases. Notably, the maximum drop in total pressure ratio and efficiency occurs at δz = 4.0 and δz = 2.0, respectively. Furthermore, the study also reveals the loss production mechanisms which driving stage performance variations. When axial spacing drops from 1.0 to 0.5, the stage loss dominated by the wake–shock interaction loss is enhanced due to the stronger wake strength. When axial spacing rises from 1.0 to 2.0, however, the wake mixing loss plays a leading role in stage loss. Additionally, larger axial spacing further amplifies wake–shock interaction due to increased viscous dissipation.
- 1 March 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (3)
Effect of blade–row axial spacing on the stage performance of an axial supersonic through-flow fan
Rotor–stator interaction has a large impact on the performance of axial compressors. Previous studies have suggested that less blade–row axial spacing (δz) of an axial flow compressor is associated with improved efficiency. However, these studies primarily focused on the subsonic-axial turbomachinery. The impact of δz on the performance in an axial supersonic through-flow fan (STFF) stage remains unclear. This study explores the effect of axial spacing on the performance of an STFF stage using unsteady numerical simulations. The results show that both the total pressure ratio and adiabatic efficiency are reduced when axial spacing changes from δz = 1.0 regardless of whether it increases or decreases. Notably, the maximum drop in total pressure ratio and efficiency occurs at δz = 4.0 and δz = 2.0, respectively. Furthermore, the study also reveals the loss production mechanisms which driving stage performance variations. When axial spacing drops from 1.0 to 0.5, the stage loss dominated by the wake–shock interaction loss is enhanced due to the stronger wake strength. When axial spacing rises from 1.0 to 2.0, however, the wake mixing loss plays a leading role in stage loss. Additionally, larger axial spacing further amplifies wake–shock interaction due to increased viscous dissipation.
- 1 October 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (10)
Unsteady numerical study on the effects of inlet distortion parameters on the aerodynamic instability of the centrifugal compressor
Total pressure inlet distortion significantly impairs the aerodynamic performance and flow stability of centrifugal compressors. This paper presents a full annulus unsteady numerical simulation to investigate the flow mechanisms under varying inlet distortion parameters. First, the flow characteristics of a uniform inflow is studied as a baseline for comparison with distorted inlet conditions. Results indicate that the interaction between shock waves and tip leakage flow is a primary factor leading to aerodynamic instability. The instability signal in this region is detected through fast Fourier transform and frequency slice wavelet transform (FSWT). Under near stall condition, different distortion parameters are set to research the effects on aerodynamic performance, flow mechanisms, and instability characteristics. The results reveal that distortion intensity has the most significant impact, causing a maximum stall margin loss of 55.43%, followed by distortion angle with a maximum stall margin loss of 43.02%. Total pressure inlet distortion leads to a deterioration in aerodynamic performance, primarily due to premature occurrences of unstable flow phenomena such as leading-edge spillage and trailing-edge backflow. The onset key features triggering aerodynamic instability are identified as leading-edge spillage vortex, tip leakage vortex, and passage vortex. The continuous disintegration of the tip leakage vortex results in low-frequency fluctuating energy exhibiting multipeak characteristics, with pulsation peaks centered around 0.5 BPF, related to the spike stall of the compressor. The high-energy frequency band dissipates over time in the time–frequency spectrum, as shown by FSWT results, indicating the characteristics of instability in the flow.
- 1 October 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (10)
Unsteady numerical study on the effects of inlet distortion parameters on the aerodynamic instability of the centrifugal compressor
Total pressure inlet distortion significantly impairs the aerodynamic performance and flow stability of centrifugal compressors. This paper presents a full annulus unsteady numerical simulation to investigate the flow mechanisms under varying inlet distortion parameters. First, the flow characteristics of a uniform inflow is studied as a baseline for comparison with distorted inlet conditions. Results indicate that the interaction between shock waves and tip leakage flow is a primary factor leading to aerodynamic instability. The instability signal in this region is detected through fast Fourier transform and frequency slice wavelet transform (FSWT). Under near stall condition, different distortion parameters are set to research the effects on aerodynamic performance, flow mechanisms, and instability characteristics. The results reveal that distortion intensity has the most significant impact, causing a maximum stall margin loss of 55.43%, followed by distortion angle with a maximum stall margin loss of 43.02%. Total pressure inlet distortion leads to a deterioration in aerodynamic performance, primarily due to premature occurrences of unstable flow phenomena such as leading-edge spillage and trailing-edge backflow. The onset key features triggering aerodynamic instability are identified as leading-edge spillage vortex, tip leakage vortex, and passage vortex. The continuous disintegration of the tip leakage vortex results in low-frequency fluctuating energy exhibiting multipeak characteristics, with pulsation peaks centered around 0.5 BPF, related to the spike stall of the compressor. The high-energy frequency band dissipates over time in the time–frequency spectrum, as shown by FSWT results, indicating the characteristics of instability in the flow.