JBJørgen Blindheim

Jørgen Blindheim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jørgen Blindheim has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Effect of Cellulose Nanofibres on Dewatering during Wet-Forming and the Mechanical Properties of Thermoformed Specimens Made of Thermomechanical and Kraft Pulps

    by Eirik Ulsaker Jacobsen, Simen Prang Følkner, Jørgen Blindheim, Dag Molteberg, Martin Steinert, Gary Chinga-Carrasco

    Due to environmental concerns regarding single-use plastic materials, major efforts are being made to develop new material concepts based on biodegradable and renewable resources, e.g., wood pulp. In this study, we assessed two types of wood pulp fibres, i.e., thermomechanical pulp (TMP) and Kraft pulp fibres, and tested the performance of the fibres in wet-moulding and thermopressing trials. Kraft pulp fibres appeared to retain more water than TMP, increasing the dewatering time during wet-moulding and apparently increasing the compression resistance of the pulp during thermoforming. Additionally, cellulose nanofibres (CNF) were added to the pulps, which improved the mechanical properties of the final thermopressed specimens. However, the addition of CNF to the pulps (from 2 to 6%) had a further decrease in the dewatering efficiency in the wet-moulding process, and this effect was more pronounced in the Kraft pulp specimens. The mechanical performance of the thermoformed specimens was in the same range as the plastic materials that are conventionally used in food packaging, i.e., modulus 0.6–1.2 GPa, strength 49 MPa and elongation 6–9%. Finally, this study demonstrates the potential of wood pulps to form three-dimensional thermoformed products.


  • Effect of Stretching on Springback in Rotary Stretch Bending of Aluminium Alloy Profiles

    by Jun Ma, Togeir Welo, Jørgen Blindheim, Taekwang Ha

    Stretch bending is widely used for manufacturing profile-type parts. However, one of the challenges faced by the bending-type forming processes is springback, which significantly reduces the dimensional accuracy of formed part, process flexibility and overall equipment effectiveness. In this study, we focus on the springback behavior in a newly developed flexible rotary stretch bending process for profiles. Using the Al-Mg-Si alloy rectangular hollow extrusions, the effect of stretching on springback, as well as process capability, is evaluated by a series of carefully designed experiments conducted for a wide range of stretching strains. Increasing the stretching strain from about 2% to 4%, the springback chord height can be reduced by about 32% and the process capability can be improved significantly, showing the strong ability of the novel flexible stretch bending strategy for controlling springback and dimensional accuracy.


  • Open Access

    Concept evaluation in new product development

    by Jørgen Blindheim, Christer W. Elverum, Torgeir Welo, Martin Steinert

    Purpose: This paper proposes the combination of rapid prototyping and physical modelling as a set-based concept evaluation method in the early stage of new product development. Design/methodology/approach: The concept evaluation method is applied in a case study of a new metal additive manufacturing process for aluminium, where a set of four extruder concepts has been modelled and evaluated. Rapid prototyping was used to produce plastic models of the different designs, and plasticine feedstock material was used to physically model the metal flow during operation. Finally, the selected concept has been verified in full-scale for processing of aluminium feedstock material. Findings: The proposed method led to several valuable insights on critical factors that were unknown at the outset of the development project. Overall, these insights enabled concept exploration and concept selection that led to a substantially better solution than the original design. Research limitations/implications: This method can be applied for other projects where numerical approaches are not applicable or capable, and where the costs or time required for producing full-scale prototypes are high. Practical implications: Employing this method can enable a more thorough exploration of the design space, allowing new solutions to be discovered. Originality/value: The proposed method allows a design team to test and evaluate multiple concepts at lower cost and time than what is usually required to produce full-scale prototypes. It is, therefore, concluded to be a valuable design strategy for the early development stages of complex products or technologies.


  • Open Access

    First demonstration of a new additive manufacturing process based on metal extrusion and solid-state bonding

    by Jørgen Blindheim, Torgeir Welo, Martin Steinert

    In this paper, a new additive manufacturing (AM) process based on extrusion and solid-state bonding is presented. The process uses metal feedstock wire which is processed in a continuous rotary extruder in order to disperse the surface oxides of the feedstock and to provide the required bonding pressure. Simultaneously, the die outlet is scraping the contact surface to provide an oxide-free interface between the extrudate and the substrate. Optical analyses of samples from a layered structure produced from AA6082 reveal that the stringers are fully merged; however, some voids and cracks are observed between the individual stringers. Still, this initial demonstration indicates that the process, upon further development, has high potential of producing near-net-shape parts at high deposition rates.


  • Open Access

    Investigating the Mechanics of Hybrid Metal Extrusion and Bonding Additive Manufacturing by FEA

    by Jørgen Blindheim, Torgeir Welo, Martin Steinert

    Hybrid Metal Extrusion & Bonding Additive Manufacturing (HYB-AM) is a hybrid manufacturing technology for the deposition of layered metal structures. This new deposition process is a complex metal forming operation, yet there is significant lack of knowledge regarding the governing mechanisms. In this work, we have used finite element analysis (FEA) to study material flow in the extruder, as well as the conditions at the interfaces of the deposited extrudate and the substrate, aiming to identify and characterize the process parameters involved. Analysis of the material flow shows that the extrusion pressure is virtually independent of the deposition rate. Furthermore, from the simulations of the material deposition sequence, it is clearly visible how the contact pressure at the interface will drop below the bonding threshold if the feed speed is too high relative to the material flow through the die. The reduced pressure also leads to the formation of a ‘gas-pocket’ inside the die, thus further degrading the conditions for bonding. The analyses of the process have provided valuable insights for the further development and industrialization of the process.