Ionut Florian Popa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ionut Florian Popa has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Dragos Mihai
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
5 shared publications - Ionut Sebastian Vintila
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
5 shared publications - Radu Mihalache
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
4 shared publications - Alexandru Paraschiv
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
3 shared publications - Cristian Dobromirescu
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
2 shared publications - Adrian Kiss
National Institute of Research and Development for Optoelectronics—INOE 2000, 409 Atomistilor St., 077125 Magurele, Romania
1 shared publication
Latest Publications
- Open Access
- 16 October 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (20) , 9448
Hydraulic Performance Comparison of Centrifugal Closed Impellers Fabricated by Means of Additive Manufacturing and Classical Machining for Space Active Thermal Control Systems of Satellites
The current paper addresses the challenges in manufacturing a critical component of a centrifugal pump for space active thermal control systems of satellites, namely, the closed centrifugal impeller. Compared to the classical technologies, there is an obvious advantage of additive manufacturing of closed impellers, due to the possibility of creating complex geometries, which boost the hydraulic performances of the part and, implicitly, of the pump. In this regard, the authors performed a comparative analysis between a closed impeller obtained by classical machining and three manufactured by additive technology (selective laser melting) by means of dimensional inspection, non-destructive testing, and experimental evaluation. The study performed here showed that the additively manufactured closed impellers exhibited similar hydraulic performances to the classical one, without the need for performing post-processing of internal surfaces. Also, in terms of dimensional and geometrical stability, the additively manufactured closed impellers were within the imposed tolerances, demonstrating the feasibility of obtaining such complex parts by using additive manufacturing. Subsequently, the allocated time for manufacturing decreased by 75% for the closed impellers manufactured by additive technologies, and the need for using four technological processes was decreased to only two, printing and post-processing.
- 16 October 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (20) , 9448
Open AccessHydraulic Performance Comparison of Centrifugal Closed Impellers Fabricated by Means of Additive Manufacturing and Classical Machining for Space Active Thermal Control Systems of Satellites
The current paper addresses the challenges in manufacturing a critical component of a centrifugal pump for space active thermal control systems of satellites, namely, the closed centrifugal impeller. Compared to the classical technologies, there is an obvious advantage of additive manufacturing of closed impellers, due to the possibility of creating complex geometries, which boost the hydraulic performances of the part and, implicitly, of the pump. In this regard, the authors performed a comparative analysis between a closed impeller obtained by classical machining and three manufactured by additive technology (selective laser melting) by means of dimensional inspection, non-destructive testing, and experimental evaluation. The study performed here showed that the additively manufactured closed impellers exhibited similar hydraulic performances to the classical one, without the need for performing post-processing of internal surfaces. Also, in terms of dimensional and geometrical stability, the additively manufactured closed impellers were within the imposed tolerances, demonstrating the feasibility of obtaining such complex parts by using additive manufacturing. Subsequently, the allocated time for manufacturing decreased by 75% for the closed impellers manufactured by additive technologies, and the need for using four technological processes was decreased to only two, printing and post-processing.
- Open Access
- 6 May 2024
- Published by MDPI AG in Inventions
- Vol. 9 (3) , 54
Satellite Thermal Management Pump Impeller Design and Optimization
This study presents a numerical approach to the design and optimization of centrifugal impellers used in the pumps of active thermal control systems of spacecraft. Although launch costs have shrunk in the last decade, the performance requirements, such as efficiency and reliability, have increased, as such systems are required to work up to 15 years, depending on the mission. To that effect, our paper deals with the first step in this pump design, namely the hydraulic optimization of the impeller. Constructively, this type of impeller allows for certain balancing systems and labyrinth seals to be applied in a more effective way, as well as allowing for additive manufacturing methods to be used—however, details regarding these aspects are beyond the scope of the current paper. By combining empirical formulas, computational fluid dynamics (CFD) analysis, and artificial neural networks (ANNs), the research focuses on achieving high efficiency and fast manufacturing. A series of geometries have been sized and validated using steady-state RANS (Reynolds Averaged Navier-Stokes) simulations, leading to the identification of the most efficient configuration. Subsequent optimization using an ANN resulted in a refined impeller design with notable improvements in hydraulic performance: a 3.55% increase in efficiency and a 7.9% increase in head. Key parameters influencing impeller performance, including blade number, incidence, and backsweep angles, are identified. This approach offers a comprehensive method to address the evolving requirements of space missions and contributes to the advancement of centrifugal pump technology in the space domain.
- 6 May 2024
- Published by MDPI AG in Inventions
- Vol. 9 (3) , 54
Open AccessSatellite Thermal Management Pump Impeller Design and Optimization
This study presents a numerical approach to the design and optimization of centrifugal impellers used in the pumps of active thermal control systems of spacecraft. Although launch costs have shrunk in the last decade, the performance requirements, such as efficiency and reliability, have increased, as such systems are required to work up to 15 years, depending on the mission. To that effect, our paper deals with the first step in this pump design, namely the hydraulic optimization of the impeller. Constructively, this type of impeller allows for certain balancing systems and labyrinth seals to be applied in a more effective way, as well as allowing for additive manufacturing methods to be used—however, details regarding these aspects are beyond the scope of the current paper. By combining empirical formulas, computational fluid dynamics (CFD) analysis, and artificial neural networks (ANNs), the research focuses on achieving high efficiency and fast manufacturing. A series of geometries have been sized and validated using steady-state RANS (Reynolds Averaged Navier-Stokes) simulations, leading to the identification of the most efficient configuration. Subsequent optimization using an ANN resulted in a refined impeller design with notable improvements in hydraulic performance: a 3.55% increase in efficiency and a 7.9% increase in head. Key parameters influencing impeller performance, including blade number, incidence, and backsweep angles, are identified. This approach offers a comprehensive method to address the evolving requirements of space missions and contributes to the advancement of centrifugal pump technology in the space domain.
- Open Access
A Microvascular System Self-Healing Approach on Polymeric Composite Materials
The paper addresses the synthesis of a nano-fibre network by coaxial electrospinning, embedding the healing agent dicyclopentadiene (DCPD) in polyacrylonitrile (PAN) fibres. Compared to other encapsulation methods, the use of nano-fibres filled with healing agent have no effect on the mechanical properties of the matrix and can address a larger healing area. Additionally, carbon nanotubes were added as nanofillers to enhance the reactivity between DCPD and the epoxydic matrix. The self-healing capability of the nano-fibre network was carried out by flexural tests, at epoxy resin level and composite level. Results obtained from Fourier transform infrared (FTIR) spectrometry, thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) confirmed the successful encapsulation of DCPD healing agent in PAN fibres. Flexural tests indicate that after 48 h, the epoxy resin has recovered 84% of its flexural strength while the composite material recovered 93%.
Open AccessA Microvascular System Self-Healing Approach on Polymeric Composite Materials
The paper addresses the synthesis of a nano-fibre network by coaxial electrospinning, embedding the healing agent dicyclopentadiene (DCPD) in polyacrylonitrile (PAN) fibres. Compared to other encapsulation methods, the use of nano-fibres filled with healing agent have no effect on the mechanical properties of the matrix and can address a larger healing area. Additionally, carbon nanotubes were added as nanofillers to enhance the reactivity between DCPD and the epoxydic matrix. The self-healing capability of the nano-fibre network was carried out by flexural tests, at epoxy resin level and composite level. Results obtained from Fourier transform infrared (FTIR) spectrometry, thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) confirmed the successful encapsulation of DCPD healing agent in PAN fibres. Flexural tests indicate that after 48 h, the epoxy resin has recovered 84% of its flexural strength while the composite material recovered 93%.
- Open Access
Manufacturing of Closed Impeller for Mechanically Pump Fluid Loop Systems Using Selective Laser Melting Additive Manufacturing Technology
In the space industry, the market demand for high-pressure mechanically pumped fluid loop (MPFL) systems has increased the interest for integrating advanced technologies in the manufacturing process of critical components with complex geometries. The conventional manufacturing process of a closed impeller encounters different technical challenges, but using additive manufacturing (AM) technology, the small component is printed, fulfilling the quality requirements. This paper presents the Laser Powder Bed Fusion (LPBF) process of a closed impeller designed for a centrifugal pump integrated in an MPFL system with the objective of defining a complete manufacturing process. A set of three closed impellers was manufactured, and each closed impeller was subjected to dimensional accuracy analysis, before and after applying an iterative finishing process for the internal surface area. One of the impellers was validated through non-destructive testing (NDT) activities, and finally, a preliminary balancing was performed for the G2.5 class. The process setup (building orientation and support structure) defined in the current study for a pre-existing geometry of the closed impeller takes full advantages of LPBF technology and represents an important step in the development of complex structural components, increasing the technological readiness level of the AM process for space applications.
Open AccessManufacturing of Closed Impeller for Mechanically Pump Fluid Loop Systems Using Selective Laser Melting Additive Manufacturing Technology
In the space industry, the market demand for high-pressure mechanically pumped fluid loop (MPFL) systems has increased the interest for integrating advanced technologies in the manufacturing process of critical components with complex geometries. The conventional manufacturing process of a closed impeller encounters different technical challenges, but using additive manufacturing (AM) technology, the small component is printed, fulfilling the quality requirements. This paper presents the Laser Powder Bed Fusion (LPBF) process of a closed impeller designed for a centrifugal pump integrated in an MPFL system with the objective of defining a complete manufacturing process. A set of three closed impellers was manufactured, and each closed impeller was subjected to dimensional accuracy analysis, before and after applying an iterative finishing process for the internal surface area. One of the impellers was validated through non-destructive testing (NDT) activities, and finally, a preliminary balancing was performed for the G2.5 class. The process setup (building orientation and support structure) defined in the current study for a pre-existing geometry of the closed impeller takes full advantages of LPBF technology and represents an important step in the development of complex structural components, increasing the technological readiness level of the AM process for space applications.
- Open Access
- 31 August 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (17) , 8115
Closing Force Evaluation of a Sample Return Capsule for a Phobos Sample Return Mission
The mission objective of the Phobos Sample Return is to collect and return 100 g of Phobos’ surface material to Earth inside a tight enclosure composed of a Vault, a Sample Container and sealing elements. One important aspect of the project was the development of a closing mechanism capable of ensuring a pushing force high enough compared to the available force of the robotic arm (40 N). The need for a higher pushing force derived from the design tests which were carried out to experimentally determine the necessary force to overcome the resistance of the sealing element when the vault is closed. Two types of sealing elements, custom made for this project, along with two SC with different geometrical shapes in the sealing area were tested. For better accuracy, the tests considered the imposed operational temperature domain for the vault, ECSS standards and the test rig set-up being performed at environmental temperature (+20 °C), −20 °C, −60 °C and +70 °C. The results of the tests highlighted that the negative temperature has a significant influence over the closing force, as this force is increasing once the operational temperature is decreasing. Based on the work performed, the most suitable type of sealing element was identified, in particular the piston geometry which allows a smaller force to close the vault.
- 31 August 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (17) , 8115
Open AccessClosing Force Evaluation of a Sample Return Capsule for a Phobos Sample Return Mission
The mission objective of the Phobos Sample Return is to collect and return 100 g of Phobos’ surface material to Earth inside a tight enclosure composed of a Vault, a Sample Container and sealing elements. One important aspect of the project was the development of a closing mechanism capable of ensuring a pushing force high enough compared to the available force of the robotic arm (40 N). The need for a higher pushing force derived from the design tests which were carried out to experimentally determine the necessary force to overcome the resistance of the sealing element when the vault is closed. Two types of sealing elements, custom made for this project, along with two SC with different geometrical shapes in the sealing area were tested. For better accuracy, the tests considered the imposed operational temperature domain for the vault, ECSS standards and the test rig set-up being performed at environmental temperature (+20 °C), −20 °C, −60 °C and +70 °C. The results of the tests highlighted that the negative temperature has a significant influence over the closing force, as this force is increasing once the operational temperature is decreasing. Based on the work performed, the most suitable type of sealing element was identified, in particular the piston geometry which allows a smaller force to close the vault.
- Open Access
- 1 July 2021
- Published by Elsevier in Acta Astronautica
- Vol. 184, 101-118
Design, analysis and evaluation of titanium antenna reflector for deep space missions
- 1 July 2021
- Published by Elsevier in Acta Astronautica
- Vol. 184, 101-118
Open AccessDesign, analysis and evaluation of titanium antenna reflector for deep space missions
- 13 August 2018
- Published by Springer Nature in CEAS Space Journal
- Vol. 11 (2) , 115-122
Finite element modelling and performance optimization of an ion thruster depending on the nature of the propellant
- 13 August 2018
- Published by Springer Nature in CEAS Space Journal
- Vol. 11 (2) , 115-122
Finite element modelling and performance optimization of an ion thruster depending on the nature of the propellant