Yohei Suzuki
Research Subjects
Yohei Suzuki has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Tatsuhiko Aizawa
Surface Engineering Design Laboratory, Shibaura Institute of Technology, Tokyo 144-0056, Japan
12 shared publications - Tomomi Shiratori
University of Toyama
12 shared publications - Tomoaki Yoshino
Komatsu-Seiki Kosakusho, Co., Ltd., Suwa 392-0012, Japan
8 shared publications Tomomi Shiratori
Academic Assembly Faculty of Engineering, University of Toyama, Toyama, Japan
3 shared publications- Masao Murakawa
Nippon Institute of Technology, 4-1 Gakuenndai, Miyashiro, Minamisaitama, Saitama 345-8501, Japan
2 shared publications - Ming Yang
Tokyo Metropolitan University
2 shared publications
Latest Publications
- Open Access
- 15 May 2024
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 41, 1248-1258
Massive nitrogen super-saturation into CoCrMo Alloys for improvement of tribological performance
The cobalt-chromium-molybdenum (CoCrMo) superalloys have been utilized in the dental, knee, and hip arthroplasty applications because of their unique combination of high strength, high wear and corrosion resistance. A massive nitrogen supersaturation (MNS) process was proposed as a surface treatment to improve these strength, hardness and ductility, further needed for hip replacement and dental prosthesis. CoCrMo disc specimens were prepared for plasma immersion nitriding at 673 K for 21.6 ks by 50 Pa. The nitrogen solute uniformly distributed in the MNS-layer with the average content of 5 mass%. Higher surface hardness than 1550 HV was attained under application of 10 N. The maximum friction coefficient was halved before and after MNS and this low frictional state with μ< 0.45 was preserved although the sliding condition by 0.1 m/s.
- 15 May 2024
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 41, 1248-1258
Open AccessMassive nitrogen super-saturation into CoCrMo Alloys for improvement of tribological performance
The cobalt-chromium-molybdenum (CoCrMo) superalloys have been utilized in the dental, knee, and hip arthroplasty applications because of their unique combination of high strength, high wear and corrosion resistance. A massive nitrogen supersaturation (MNS) process was proposed as a surface treatment to improve these strength, hardness and ductility, further needed for hip replacement and dental prosthesis. CoCrMo disc specimens were prepared for plasma immersion nitriding at 673 K for 21.6 ks by 50 Pa. The nitrogen solute uniformly distributed in the MNS-layer with the average content of 5 mass%. Higher surface hardness than 1550 HV was attained under application of 10 N. The maximum friction coefficient was halved before and after MNS and this low frictional state with μ< 0.45 was preserved although the sliding condition by 0.1 m/s.
- Open Access
- 3 May 2023
- Published by IntechOpen
Plasma Nitriding-Assisted 3D Printing for Die Technology in Digital Micro-Manufacturing
A plasma nitriding-assisted 3D printing method was developed to build up the micro-punch and micro-die systems. Two dimensional punch head and core-die cavity geometries were ink-jet printed or screen-printed onto the AISI316 and SKD11 tool substrate surfaces in following their two-dimensional computer-aided design (CAD) data. The low-temperature plasma nitriding process was utilized to make nitrogen supersaturation only into the unprinted substrates. The sand-blasting and chemical etching were utilized to mechanically or chemically remove the printed parts from punch and die substrate. As sand-blasted and chemically etched AISI316 and SKD11 punches and core-dies were simply finished and used as a die set for micro-embossing, micro-piercing and micro-punching processes. In particular, a micro-pump was selected as a miniature mechanical element. Its 3D CAD geometry was sliced to 2D CAD data for each functional AISI304 stainless steel sheet. A pair of punch and die for each 2D CAD geometry for constituent sheet was prepared by the plasma nitriding-assisted 3D printing. Each sheet was punched out by using this set of punch and die to functionalize each sheet unit in correspondence to the sliced CAD data. These constituent sheets were assembled and joined to a structural unit of micro-pump.
- 3 May 2023
- Published by IntechOpen
Open AccessPlasma Nitriding-Assisted 3D Printing for Die Technology in Digital Micro-Manufacturing
A plasma nitriding-assisted 3D printing method was developed to build up the micro-punch and micro-die systems. Two dimensional punch head and core-die cavity geometries were ink-jet printed or screen-printed onto the AISI316 and SKD11 tool substrate surfaces in following their two-dimensional computer-aided design (CAD) data. The low-temperature plasma nitriding process was utilized to make nitrogen supersaturation only into the unprinted substrates. The sand-blasting and chemical etching were utilized to mechanically or chemically remove the printed parts from punch and die substrate. As sand-blasted and chemically etched AISI316 and SKD11 punches and core-dies were simply finished and used as a die set for micro-embossing, micro-piercing and micro-punching processes. In particular, a micro-pump was selected as a miniature mechanical element. Its 3D CAD geometry was sliced to 2D CAD data for each functional AISI304 stainless steel sheet. A pair of punch and die for each 2D CAD geometry for constituent sheet was prepared by the plasma nitriding-assisted 3D printing. Each sheet was punched out by using this set of punch and die to functionalize each sheet unit in correspondence to the sliced CAD data. These constituent sheets were assembled and joined to a structural unit of micro-pump.
- 1 January 2023
- Published by The Japan Society for Technology and Plasticity in Journal of the Japan Society for Technology of Plasticity
- Vol. 64 (751) , 131-136
Development of Piercing Punch for High Durability and Product Quality in Laminate Shearing of Amorphous Alloy Foil
The conventional shearing of amorphous alloy foil induced significant damage in them because of their high strength and low ductility. New shearing tools with a tailored chamfer at the punch cutting edge were proposed. The chamfer size was varied to describe its effect on the shearing behavior. Without chamfers, chipping occurred at the punch cutting edge after only 100 shots. No chipping was observed even after 1000 shots when using the chamfered punch, irrespective of the chamfer size. In particular, when the chamfer size was reduced to 10 μm, no chipping occurred, and the punch cutting edge was only slightly worn even after 50,000 repetitions of piercing the five-laminate amorphous alloy foil stack. This well-conditioned punch cutting edge resulted in the formation of high-quality pierced holes.
- 1 January 2023
- Published by The Japan Society for Technology and Plasticity in Journal of the Japan Society for Technology of Plasticity
- Vol. 64 (751) , 131-136
Development of Piercing Punch for High Durability and Product Quality in Laminate Shearing of Amorphous Alloy Foil
The conventional shearing of amorphous alloy foil induced significant damage in them because of their high strength and low ductility. New shearing tools with a tailored chamfer at the punch cutting edge were proposed. The chamfer size was varied to describe its effect on the shearing behavior. Without chamfers, chipping occurred at the punch cutting edge after only 100 shots. No chipping was observed even after 1000 shots when using the chamfered punch, irrespective of the chamfer size. In particular, when the chamfer size was reduced to 10 μm, no chipping occurred, and the punch cutting edge was only slightly worn even after 50,000 repetitions of piercing the five-laminate amorphous alloy foil stack. This well-conditioned punch cutting edge resulted in the formation of high-quality pierced holes.
- Open Access
- 2 November 2022
- Published by IntechOpen
Femtosecond Laser Micro-/Nano-Texturing to Die Substrates for Fine Imprinting to Products
A femtosecond laser micro−/nano-texturing was proposed to fabricate the coated and surface treated dies with the tailored textures for surface decoration and surface property control of metal, polymer and glass products. The polygonal model for microtextures with nanotextures by the LIPSS-effect was utilized to fabricate a DLC-coated SKD11 die with a star-shaped emblem. This die was set up into the cassette die set for directly imprinting this emblem into aluminum alloy and PET sheets. The periodic surface structure was synthesized as a surface geometry model to build up the super-hydrophobic surface on the nitrogen supersaturated AISI316 die. This die was also set up into a hot stamping system to directly imprint the hydrophobic surface onto the phosphorous glass products. Through the femtosecond laser micro−/nano-texturing and CNC-imprinting, the metal, polymer and glass product surfaces were optically decorated to have color grating and plasmonic brilliance and functionally controlled to be hydrophobic.
- 2 November 2022
- Published by IntechOpen
Open AccessFemtosecond Laser Micro-/Nano-Texturing to Die Substrates for Fine Imprinting to Products
A femtosecond laser micro−/nano-texturing was proposed to fabricate the coated and surface treated dies with the tailored textures for surface decoration and surface property control of metal, polymer and glass products. The polygonal model for microtextures with nanotextures by the LIPSS-effect was utilized to fabricate a DLC-coated SKD11 die with a star-shaped emblem. This die was set up into the cassette die set for directly imprinting this emblem into aluminum alloy and PET sheets. The periodic surface structure was synthesized as a surface geometry model to build up the super-hydrophobic surface on the nitrogen supersaturated AISI316 die. This die was also set up into a hot stamping system to directly imprint the hydrophobic surface onto the phosphorous glass products. Through the femtosecond laser micro−/nano-texturing and CNC-imprinting, the metal, polymer and glass product surfaces were optically decorated to have color grating and plasmonic brilliance and functionally controlled to be hydrophobic.
- Open Access
- 14 September 2022
- Published by IntechOpen
Nitrogen Supersaturation of AISI316 Base Stainless Steels at 673 K and 623 K for Hardening and Microstructure Control
The high-density plasma nitriding at 673 K and 623 K was employed to make 10% of nitrogen supersaturation on AISI316 base austenitic stainless steels. The processing parameters and nitrogen-hydrogen gas flow ratio were optimized to increase the yield of N2+ ion and NH-radical for efficient nitriding. The nitrided AISI316 specimens were prepared for multidimensional analysis to describe the fundamental features of low-temperature plasma nitriding. First, macroscopic evaluation revealed that nitrogen supersaturation induced the γ-lattice expansion and the higher nitrogen content than 4% of mass in depth. The mesoscopic analysis describes the holding temperature and initial grain-size effects on the microstructure changes. Plastic straining, grain-size refinement, and nitrogen zone-boundary diffusion processes advance with nitrogen supersaturation to drive the inner nitriding behavior. The microscopic analysis explains the microstructure refinement, the two-phase structuring, and the microstructure modification. Through this multi-dimensional analysis, the essential characteristics of the low-temperature plasma nitriding of 316 austenitic stainless steels were precisely understood to extend the engineering treatise on the bulk nitrogen stainless steels for surface modification and treatment of stainless steels by nitriding. This plasma nitriding was applied to strengthen and harden the AISI316 wire surfaces toward its application on surgery wires.
- 14 September 2022
- Published by IntechOpen
Open AccessNitrogen Supersaturation of AISI316 Base Stainless Steels at 673 K and 623 K for Hardening and Microstructure Control
The high-density plasma nitriding at 673 K and 623 K was employed to make 10% of nitrogen supersaturation on AISI316 base austenitic stainless steels. The processing parameters and nitrogen-hydrogen gas flow ratio were optimized to increase the yield of N2+ ion and NH-radical for efficient nitriding. The nitrided AISI316 specimens were prepared for multidimensional analysis to describe the fundamental features of low-temperature plasma nitriding. First, macroscopic evaluation revealed that nitrogen supersaturation induced the γ-lattice expansion and the higher nitrogen content than 4% of mass in depth. The mesoscopic analysis describes the holding temperature and initial grain-size effects on the microstructure changes. Plastic straining, grain-size refinement, and nitrogen zone-boundary diffusion processes advance with nitrogen supersaturation to drive the inner nitriding behavior. The microscopic analysis explains the microstructure refinement, the two-phase structuring, and the microstructure modification. Through this multi-dimensional analysis, the essential characteristics of the low-temperature plasma nitriding of 316 austenitic stainless steels were precisely understood to extend the engineering treatise on the bulk nitrogen stainless steels for surface modification and treatment of stainless steels by nitriding. This plasma nitriding was applied to strengthen and harden the AISI316 wire surfaces toward its application on surgery wires.
- Open Access
- 20 April 2022
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 6 (3) , 49
Fabrication of Punch and Die Using Plasma-Assisted 3D Printing Technology for Piercing Sheet Metals
A pair of punch and die was often fabricated using subtractive manufacturing processes such as milling and other machining processes. However, additive manufacturing could be used to perform the same processes. This study explored this possibility. In particular, this study fabricated a pair of T-shaped punch and die made of AISI316L austenitic stainless steel using an additive manufacturing process called plasma-assisted 3D printing. Accordingly, T-shaped negative and positive 2D patterns were screen-printed onto the mirror-polished surfaces of the substrates made of AISI316L austenitic stainless steel. The printed film worked like a mask to prevent the printed substrate surfaces from nitriding. In order to form a thick nitrided layer, the unprinted substrate surfaces were selectively nitrided at 673 K for 14.4 ks. The un-nitrided segments of the substrates were uniformly removed by sand-blasting that involved shooting silica particles on the substrate’s surfaces. As a result, the substrates printed with negative and positive T-shaped patterns were transformed into the punch head and die cavity. In order to see the efficacy of the fabricated punch and die pair, this pair was used for piercing the electrical steel sheets under a controlled clearance. Scanning Electron Microscopy with Energy Dispersive X-ray (SEM-EDX) was used to measure surface topography after piercing. In addition, SEM and a 3D profilometer were used to measure the punch and die profiles after piercing. The abovementioned measurement results showed that the fabricated punch and die exhibited highly accurate piercing behavior. Thus, the plasma-assisted 3D printing was useful for punch and die fabrication.
- 20 April 2022
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 6 (3) , 49
Open AccessFabrication of Punch and Die Using Plasma-Assisted 3D Printing Technology for Piercing Sheet Metals
A pair of punch and die was often fabricated using subtractive manufacturing processes such as milling and other machining processes. However, additive manufacturing could be used to perform the same processes. This study explored this possibility. In particular, this study fabricated a pair of T-shaped punch and die made of AISI316L austenitic stainless steel using an additive manufacturing process called plasma-assisted 3D printing. Accordingly, T-shaped negative and positive 2D patterns were screen-printed onto the mirror-polished surfaces of the substrates made of AISI316L austenitic stainless steel. The printed film worked like a mask to prevent the printed substrate surfaces from nitriding. In order to form a thick nitrided layer, the unprinted substrate surfaces were selectively nitrided at 673 K for 14.4 ks. The un-nitrided segments of the substrates were uniformly removed by sand-blasting that involved shooting silica particles on the substrate’s surfaces. As a result, the substrates printed with negative and positive T-shaped patterns were transformed into the punch head and die cavity. In order to see the efficacy of the fabricated punch and die pair, this pair was used for piercing the electrical steel sheets under a controlled clearance. Scanning Electron Microscopy with Energy Dispersive X-ray (SEM-EDX) was used to measure surface topography after piercing. In addition, SEM and a 3D profilometer were used to measure the punch and die profiles after piercing. The abovementioned measurement results showed that the fabricated punch and die exhibited highly accurate piercing behavior. Thus, the plasma-assisted 3D printing was useful for punch and die fabrication.
- Open Access
- 31 March 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (4) , 562
Quantitative Characterization of the Affected Zones in a Single Crystal Fe-6Si Steel Sheet by Fine Piercing
An iron loss in the motor core was often enhanced by formation of plastically affected zones in piercing the electrical steel sheets. A platform methodology to carry out quantitative evaluation of these affected zones in the pierced electrical steel sheets was proposed to search for the way to minimize the affected zone widths. A coarse-grained electrical steel sheet was employed as a work material for a fine piercing experiment under the narrowed clearance between the plasma-nitrided SKD11 punch and core-die. The shearing behavior by the applied loading for piercing was described by in situ measurement of the load-stroke relationship. The plastic straining in the single-crystal electrical steel sheet was characterized by SEM (scanning electron microscopy) and EBSD (electron back-scattering diffraction) to define the affected zone size and to analyze the rotation of crystallographic orientations by the induced plastic distortion during piercing. Integral and differentiation of spin rotation measured the affected zones. The effect of punch edge sharpness on these spin-rotation measures was also discussed using the nitrided and ion-milled SKD11 punch and core-die.
- 31 March 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (4) , 562
Open AccessQuantitative Characterization of the Affected Zones in a Single Crystal Fe-6Si Steel Sheet by Fine Piercing
An iron loss in the motor core was often enhanced by formation of plastically affected zones in piercing the electrical steel sheets. A platform methodology to carry out quantitative evaluation of these affected zones in the pierced electrical steel sheets was proposed to search for the way to minimize the affected zone widths. A coarse-grained electrical steel sheet was employed as a work material for a fine piercing experiment under the narrowed clearance between the plasma-nitrided SKD11 punch and core-die. The shearing behavior by the applied loading for piercing was described by in situ measurement of the load-stroke relationship. The plastic straining in the single-crystal electrical steel sheet was characterized by SEM (scanning electron microscopy) and EBSD (electron back-scattering diffraction) to define the affected zone size and to analyze the rotation of crystallographic orientations by the induced plastic distortion during piercing. Integral and differentiation of spin rotation measured the affected zones. The effect of punch edge sharpness on these spin-rotation measures was also discussed using the nitrided and ion-milled SKD11 punch and core-die.
- Open Access
Fine Piercing of Amorphous Electrical Steel Sheet Stack by Micro-/Nano-Textured Punch
The periodic nanotexture was superposed to the micro-textured grooves on the side surface of the punch. These grooves with nanotextures were shaped to have parallel and vertical orientations to the punch stroke direction, respectively. A stack of five amorphous electrical steel sheets was punched out with these micro-/nano-textured punches. The process affected zone at the vicinity of the punched hole was analyzed by SEM (Scanning Electron Microscopy) and a three-dimensional profilometer. The punch surfaces were also observed by SEM to describe the debris particle adhesion on them. The dimensional change in each layer of the stack before and after perforation was measured to describe the punching behavior with the comparison to the punch diameter.
Open AccessFine Piercing of Amorphous Electrical Steel Sheet Stack by Micro-/Nano-Textured Punch
The periodic nanotexture was superposed to the micro-textured grooves on the side surface of the punch. These grooves with nanotextures were shaped to have parallel and vertical orientations to the punch stroke direction, respectively. A stack of five amorphous electrical steel sheets was punched out with these micro-/nano-textured punches. The process affected zone at the vicinity of the punched hole was analyzed by SEM (Scanning Electron Microscopy) and a three-dimensional profilometer. The punch surfaces were also observed by SEM to describe the debris particle adhesion on them. The dimensional change in each layer of the stack before and after perforation was measured to describe the punching behavior with the comparison to the punch diameter.
- Open Access
- 6 February 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (2) , 265
Micro-/Nano-Texturing onto Plasma-Nitrided Tool Surface by Laser Printing for CNC Imprinting and Piercing
A new data transformation method for micro-manufacturing using a topological model for a micro-/nano-texture was proposed for a surface-decorated product. Femtosecond laser printing was utilized to form the micro-/nano-textures into the hardened thick layer of dies by plasma nitriding. At first, the plasma-nitrided AISI316L flat substrate was laser-printed as a punch to imprint the tailored nano-textures onto the AA1060 aluminum plate for its surface decoration with topological emblems. Second, the plasma-nitrided SKD11 cylindrical punch was laser-trimmed to form the nanostructures on its side surface. This nano-texture was imprinted onto the hole surface concurrently with piercing a circular hole into electrical steel sheet. The fully burnished surface had a shiny, metallic quality due to the nano-texturing. The plasma nitriding, the laser printing and the CNC (computer numerical control) imprinting provided a way of transforming the tailored textures on the metallic product.
- 6 February 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (2) , 265
Open AccessMicro-/Nano-Texturing onto Plasma-Nitrided Tool Surface by Laser Printing for CNC Imprinting and Piercing
A new data transformation method for micro-manufacturing using a topological model for a micro-/nano-texture was proposed for a surface-decorated product. Femtosecond laser printing was utilized to form the micro-/nano-textures into the hardened thick layer of dies by plasma nitriding. At first, the plasma-nitrided AISI316L flat substrate was laser-printed as a punch to imprint the tailored nano-textures onto the AA1060 aluminum plate for its surface decoration with topological emblems. Second, the plasma-nitrided SKD11 cylindrical punch was laser-trimmed to form the nanostructures on its side surface. This nano-texture was imprinted onto the hole surface concurrently with piercing a circular hole into electrical steel sheet. The fully burnished surface had a shiny, metallic quality due to the nano-texturing. The plasma nitriding, the laser printing and the CNC (computer numerical control) imprinting provided a way of transforming the tailored textures on the metallic product.
- Open Access
- 18 August 2021
- Published by IntechOpen
Laser Treatment CVD Diamond Coated Punch for Ultra-Fine Piercing of Metallic Sheets
CVD-diamond coated special tools have been widely utilized to prolong their tool life in practical production lines. WC (Co) punch for fine piercing of metallic sheets required for high wear-toughness to be free from chipping and damages and for high product quality to punch out the holes with sufficient dimensional accuracy. The laser trimming process was developed to reduce the surface roughness of diamond coating down to submicron level and to adjust its diamond layer dimensions with a sharp punch edge for accurate piercing. The pulsed laser irradiation was employed to demonstrate that micro-groove was accurately formed into the diamond coating. Less deterioration in the worked diamond film by this laser treatment was proved by the Raman spectroscopy. The femtosecond laser trimming was proposed to sharpen the punch edge down to 2 μm and to form the nano-textured punch side surfaces with the LIPSS (Laser Induced Periodic Surface Structuring)-period of 300 nm. Fine piercing experiments were performed to demonstrate that punch life was significantly extended to continuous punching in more than 10,000 shots and that mirror-shining hole surfaces were attained in every shot by regularly coining the nanotextures. The sharp punch edge with homogeneous edge profile was responsible for reduction of the induced damages into work sheet by piercing. The punch life was extended by the ejection mechanism of debris particles through the nanotextures on the punch side surface. The present laser treatment was useful in trimming and nanostructuring the complex-shaped punch edge for industrial application.
- 18 August 2021
- Published by IntechOpen
Open AccessLaser Treatment CVD Diamond Coated Punch for Ultra-Fine Piercing of Metallic Sheets
CVD-diamond coated special tools have been widely utilized to prolong their tool life in practical production lines. WC (Co) punch for fine piercing of metallic sheets required for high wear-toughness to be free from chipping and damages and for high product quality to punch out the holes with sufficient dimensional accuracy. The laser trimming process was developed to reduce the surface roughness of diamond coating down to submicron level and to adjust its diamond layer dimensions with a sharp punch edge for accurate piercing. The pulsed laser irradiation was employed to demonstrate that micro-groove was accurately formed into the diamond coating. Less deterioration in the worked diamond film by this laser treatment was proved by the Raman spectroscopy. The femtosecond laser trimming was proposed to sharpen the punch edge down to 2 μm and to form the nano-textured punch side surfaces with the LIPSS (Laser Induced Periodic Surface Structuring)-period of 300 nm. Fine piercing experiments were performed to demonstrate that punch life was significantly extended to continuous punching in more than 10,000 shots and that mirror-shining hole surfaces were attained in every shot by regularly coining the nanotextures. The sharp punch edge with homogeneous edge profile was responsible for reduction of the induced damages into work sheet by piercing. The punch life was extended by the ejection mechanism of debris particles through the nanotextures on the punch side surface. The present laser treatment was useful in trimming and nanostructuring the complex-shaped punch edge for industrial application.