Andy Durrant
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Andy Durrant has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Abidemi Olawunmi Adisa
University of the West of Scotland, UK
3 shared publications - Cristina Rodriguez
Department of Engineering & Smart Infrastructure (ESI), Faculty of Computing, Sciences & Engineering, University of the West of Scotland, Paisley PA1 2BE, UK
3 shared publications - Abdul Ghani Olabi
University of Sharjah
2 shared publications - Ruth Chinyere Anyanwu
School of Computing, Engineering and Physical Sciences, University of the West of Scotland, Paisley PA1 2BE, UK
2 shared publications - Amarnath Krishnamoorthy
School of Engineering and Computing, University of the West of Scotland, Paisley PA1 2BE, UK
1 shared publication
Latest Publications
- Open Access
- 29 February 2024
- Published by MDPI AG in Preprints.org
Foam Control Mechanisms in Anaerobic Digestion Systems
Anaerobic digestion of waste material to biogas, with the remaining digestate slurry used as agricultural biofertilizer, is already a route of sustainable fuel production and its uptake will grow further. However, the foam layer that forms on top of the reacting mixture impedes the process and leads to liquid and solid material contaminating the gas product. Ideally, any effective foam repression should be low-cost, and react fast. Therefore, methods of optimizing anaerobic digestion need foam repression as one of the parameters in increasing gas yield. Foam can be repressed by pre-treating substrate which destroys filamentous bacteria and adding trace elements. The drawback to this method is the high cost of pre-treatment, the trace elements not being biodegradable and being toxic at high concentration; this method does not completely repress foam and is only effective under moderate organic loading
- 29 February 2024
- Published by MDPI AG in Preprints.org
Open AccessFoam Control Mechanisms in Anaerobic Digestion Systems
Anaerobic digestion of waste material to biogas, with the remaining digestate slurry used as agricultural biofertilizer, is already a route of sustainable fuel production and its uptake will grow further. However, the foam layer that forms on top of the reacting mixture impedes the process and leads to liquid and solid material contaminating the gas product. Ideally, any effective foam repression should be low-cost, and react fast. Therefore, methods of optimizing anaerobic digestion need foam repression as one of the parameters in increasing gas yield. Foam can be repressed by pre-treating substrate which destroys filamentous bacteria and adding trace elements. The drawback to this method is the high cost of pre-treatment, the trace elements not being biodegradable and being toxic at high concentration; this method does not completely repress foam and is only effective under moderate organic loading
- Open Access
- 28 February 2024
- Published by MDPI AG in Preprints.org
Anaerobic Digestion’s Process Stability Parameters for Maximizing Methane Yield
The mechanical pre-treatment constitutes an unavoidable pre-step prior to biofuels conversion. As the cost of this step is often underestimated, recently researchers have striven to identify and characterize the mechanical pre-treatment effects in terms of post-treatment physical characterization, derived improvement of enzymatic digestibility, and output yields. The status of existing mechanical pre-treatment techniques is reviewed by substrate’s typology for lignocellulose biomass, focusing on comminution techniques. Emphasis has been dedicated to the particle size achieved after treatment, crystallinity breakage and eventual inhibitory phenomena deriving from the application of particle size reduction, which are analysed and discussed.
- 28 February 2024
- Published by MDPI AG in Preprints.org
Open AccessAnaerobic Digestion’s Process Stability Parameters for Maximizing Methane Yield
The mechanical pre-treatment constitutes an unavoidable pre-step prior to biofuels conversion. As the cost of this step is often underestimated, recently researchers have striven to identify and characterize the mechanical pre-treatment effects in terms of post-treatment physical characterization, derived improvement of enzymatic digestibility, and output yields. The status of existing mechanical pre-treatment techniques is reviewed by substrate’s typology for lignocellulose biomass, focusing on comminution techniques. Emphasis has been dedicated to the particle size achieved after treatment, crystallinity breakage and eventual inhibitory phenomena deriving from the application of particle size reduction, which are analysed and discussed.
- Open Access
- 27 February 2024
- Published by MDPI AG in Preprints.org
Optimizing Methane Yield through Anaerobic Digestion Using Hollander Beater as Mechanical Pre-Treatment Method
The UN Sustainable Development Goal 7 Report 2022 is about ensuring access to clean and affordable energy, which is key to the development of agriculture, business, communications, education, healthcare, and transportation. The lack of access to energy hinders economic and human development. Nevertheless, the current pace of progress is insufficient to achieve Goal 7 by 2030. Huge disparities in access to modern sustainable energy persist. Rising commodity, energy and shipping prices have increased the cost of producing and transporting solar photovoltaics modules, wind turbines and biofuels worldwide, adding uncertainty to a development trajectory that is already far below Goal 7 ambitions. Achieving energy and climate goals will require continued policy support and a massive mobilization of public and private capital for clean and renewable energy such as methane from biomass. An important factor in improving methane yield from biomass waste is pre-treatment of the biomass prior to anaerobic digestion. Size reduction of lignocellulose biomass is important for changing and increasing digestibility thus increasing methane yield. A Hollander beater was used as the mechanical pre-treatment machine throughout this study. Results indicate that methane yield is directly proportional to feedstock/Inoculum (F/I) ratio as higher F/I ratio led to higher methane yield. It was observed at an F/I ratio of 0.5 that 5 minutes pre-treatment time produced highest methane yield, while the lowest methane yield was observed at an F/I ratio of 0.2 with 1 minute of pre-treatment time. Methane yield decreased by 30% from 140 mL gTS-1 at F/I ratio 0.5 with 5 minutes pre-treatment time to 98 mL gTS-1 at F/I 0.2 with 5 minutes pre-treatment time. The optimum methane yield was attained at high F/I ratio allowing sufficient nutrient essential for complete degradation of biomass. Overall, this research shows the Hollander beater is not efficient in optimizing methane yield for cardboard.
- 27 February 2024
- Published by MDPI AG in Preprints.org
Open AccessOptimizing Methane Yield through Anaerobic Digestion Using Hollander Beater as Mechanical Pre-Treatment Method
The UN Sustainable Development Goal 7 Report 2022 is about ensuring access to clean and affordable energy, which is key to the development of agriculture, business, communications, education, healthcare, and transportation. The lack of access to energy hinders economic and human development. Nevertheless, the current pace of progress is insufficient to achieve Goal 7 by 2030. Huge disparities in access to modern sustainable energy persist. Rising commodity, energy and shipping prices have increased the cost of producing and transporting solar photovoltaics modules, wind turbines and biofuels worldwide, adding uncertainty to a development trajectory that is already far below Goal 7 ambitions. Achieving energy and climate goals will require continued policy support and a massive mobilization of public and private capital for clean and renewable energy such as methane from biomass. An important factor in improving methane yield from biomass waste is pre-treatment of the biomass prior to anaerobic digestion. Size reduction of lignocellulose biomass is important for changing and increasing digestibility thus increasing methane yield. A Hollander beater was used as the mechanical pre-treatment machine throughout this study. Results indicate that methane yield is directly proportional to feedstock/Inoculum (F/I) ratio as higher F/I ratio led to higher methane yield. It was observed at an F/I ratio of 0.5 that 5 minutes pre-treatment time produced highest methane yield, while the lowest methane yield was observed at an F/I ratio of 0.2 with 1 minute of pre-treatment time. Methane yield decreased by 30% from 140 mL gTS-1 at F/I ratio 0.5 with 5 minutes pre-treatment time to 98 mL gTS-1 at F/I 0.2 with 5 minutes pre-treatment time. The optimum methane yield was attained at high F/I ratio allowing sufficient nutrient essential for complete degradation of biomass. Overall, this research shows the Hollander beater is not efficient in optimizing methane yield for cardboard.
- Open Access
- 11 August 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (16) , 9953
Sustainable Approaches to Microalgal Pre-Treatment Techniques for Biodiesel Production: A Review
Microalgae are a potential source of numerous nutritional products and biofuels. Their applications range from the food industry to the medical and fuel sectors and beyond. Recently, the conversion of biomass into biodiesel and other biofuels has received a lot of positive attention within the fossil fuel arena. The objective of biorefineries is to focus on utilising biomass efficiently to produce quality biofuel products by minimising the input as well as to reduce the use of chemical or thermal pre-treatments. Pre-treatment processes in biorefineries involve cell disruption to obtain lipids. Cell disruption is a crucial part of bioconversion, as the structure and nature of microalgae cell walls are complex. In recent years, many research papers have shown various pre-treatment methods and their advantages. The objective of this paper was to provide a comprehensive in-depth review of various recent pre-treatment techniques that have been used for microalgal biodiesel production and to discuss their advantages, disadvantages, and how they are applied in algal biorefineries.
- 11 August 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (16) , 9953
Open AccessSustainable Approaches to Microalgal Pre-Treatment Techniques for Biodiesel Production: A Review
Microalgae are a potential source of numerous nutritional products and biofuels. Their applications range from the food industry to the medical and fuel sectors and beyond. Recently, the conversion of biomass into biodiesel and other biofuels has received a lot of positive attention within the fossil fuel arena. The objective of biorefineries is to focus on utilising biomass efficiently to produce quality biofuel products by minimising the input as well as to reduce the use of chemical or thermal pre-treatments. Pre-treatment processes in biorefineries involve cell disruption to obtain lipids. Cell disruption is a crucial part of bioconversion, as the structure and nature of microalgae cell walls are complex. In recent years, many research papers have shown various pre-treatment methods and their advantages. The objective of this paper was to provide a comprehensive in-depth review of various recent pre-treatment techniques that have been used for microalgal biodiesel production and to discuss their advantages, disadvantages, and how they are applied in algal biorefineries.
- Open Access
- 17 May 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (10) , 6108
Evaluation of Growth Rate and Biomass Productivity of Scenedesmus quadricauda and Chlorella vulgaris under Different LED Wavelengths and Photoperiods
Cultivation has been identified as an essential stage for biofuel production. This research has examined two important parameters for the industrial production of microalgae, namely microalgae growth rate and biomass productivity. Chlorella vulgaris and Scenedesmusquadricauda were cultivated using a closed photobioreactor (PBR). A novel approach for cultivation and energy input reduction was developed by incorporating periods of darkness during cultivation, as would happen in nature. Three different LED light sources (white, red, and green) were used to determine the conditions that result in the highest growth rate and biomass productivity. C. vulgaris and S. quadricauda responded differently to lighting conditions. It was found that, depending on the LED source and light period, different growth rates and biomass productivities were obtained. Overall, experimental results obtained in this study indicated that a white LED is more effective than green or red LEDs in increasing microalgae growth rate and biomass productivity. A maximum growth rate of 3.41 d−1 and a biomass productivity of 2.369 g L−1d−1 were achieved for S.quadricauda under a 19 h period of white light alternating with 5 h of darkness. For C. vulgaris the maximum growth rate of 3.49 d−1 and maximum biomass productivity of 2.438 g L−1d−1 were achieved by continuous white light with no darkness period.
- 17 May 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (10) , 6108
Open AccessEvaluation of Growth Rate and Biomass Productivity of Scenedesmus quadricauda and Chlorella vulgaris under Different LED Wavelengths and Photoperiods
Cultivation has been identified as an essential stage for biofuel production. This research has examined two important parameters for the industrial production of microalgae, namely microalgae growth rate and biomass productivity. Chlorella vulgaris and Scenedesmusquadricauda were cultivated using a closed photobioreactor (PBR). A novel approach for cultivation and energy input reduction was developed by incorporating periods of darkness during cultivation, as would happen in nature. Three different LED light sources (white, red, and green) were used to determine the conditions that result in the highest growth rate and biomass productivity. C. vulgaris and S. quadricauda responded differently to lighting conditions. It was found that, depending on the LED source and light period, different growth rates and biomass productivities were obtained. Overall, experimental results obtained in this study indicated that a white LED is more effective than green or red LEDs in increasing microalgae growth rate and biomass productivity. A maximum growth rate of 3.41 d−1 and a biomass productivity of 2.369 g L−1d−1 were achieved for S.quadricauda under a 19 h period of white light alternating with 5 h of darkness. For C. vulgaris the maximum growth rate of 3.49 d−1 and maximum biomass productivity of 2.438 g L−1d−1 were achieved by continuous white light with no darkness period.
- Open Access
Optimisation of Tray Drier Microalgae Dewatering Techniques Using Response Surface Methodology
The feasibility of the application of a tray drier in dewatering microalgae was investigated. Response surface methodology (RSM) based on Central Composite Design (CCD) was used to evaluate and optimise the effect of air temperature and air velocity as independent variables on the dewatering efficiency as a response function. The significance of independent variables and their interactions was tested by means of analysis of variance (ANOVA) with a 95% confidence level. Results indicate that the air supply temperature was the main parameter affecting dewatering efficiency, while air velocity had a slight effect on the process. The optimum operating conditions to achieve maximum dewatering were determined: air velocities and temperatures ranged between 4 to 10 m/s and 40 to 56 °C respectively. An optimised dewatering efficiency of 92.83% was achieved at air an velocity of 4 m/s and air temperature of 48 °C. Energy used per 1 kg of dry algae was 0.34 kWh.
Open AccessOptimisation of Tray Drier Microalgae Dewatering Techniques Using Response Surface Methodology
The feasibility of the application of a tray drier in dewatering microalgae was investigated. Response surface methodology (RSM) based on Central Composite Design (CCD) was used to evaluate and optimise the effect of air temperature and air velocity as independent variables on the dewatering efficiency as a response function. The significance of independent variables and their interactions was tested by means of analysis of variance (ANOVA) with a 95% confidence level. Results indicate that the air supply temperature was the main parameter affecting dewatering efficiency, while air velocity had a slight effect on the process. The optimum operating conditions to achieve maximum dewatering were determined: air velocities and temperatures ranged between 4 to 10 m/s and 40 to 56 °C respectively. An optimised dewatering efficiency of 92.83% was achieved at air an velocity of 4 m/s and air temperature of 48 °C. Energy used per 1 kg of dry algae was 0.34 kWh.