Piyachat Wattanachai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Piyachat Wattanachai has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Christian Antonio
2 shared publicationsPatiparn Boonruam
2 shared publicationsBenjawan Buasathain
Department of Chemical Engineering, Faculty of Engineering, Burapha University, Sean Sook, Muang, Chonburi 20131, Thailand
1 shared publicationCharin Maungnakum
1 shared publicationHéctor Morillas
1 shared publicationNattapron Siribanluehan
Department of Chemical Engineering, Faculty of Engineering Burapha University Chonburi Thailand
1 shared publication
Latest Publications
- Open Access
- 2 October 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Nitrogen-Containing Functionalization on CO₂ Capture and Stability of Zeolite 5A in Packed Beds
The development of low-cost and durable adsorbents for post-combustion CO₂ capture remains a critical challenge. In this study, zeolite LTA 5A was modified using aqueous ammonia (NH₄OH) and monoethanolamine (MEA) to examine how nitrogen-containing additives influence surface properties and CO₂ adsorption performance in both powder and granulated forms. Structural and physicochemical characterization (XRD, SEM–EDS, FTIR, BET, and CO₂-TPD) confirmed preservation of the zeolite framework after modification, while spectroscopic and desorption analyses indicated the introduction of nitrogen-containing functionalities. Considering the limitations of EDS for nitrogen quantification, correlations are drawn based on observable changes in surface chemistry and porosity. Functionalization reduced N₂-accessible surface area and pore volume but enhanced CO₂ affinity under dynamic conditions. In fixed-bed breakthrough experiments at ambient conditions with 5 vol.% CO₂, the NH₄OH-modified powder exhibited the highest dynamic capacity (8.8 mmol g⁻¹) and capture efficiency (68%), outperforming unmodified and MEA-treated samples. Additionally, the NH₄OH-functionalized adsorbent demonstrated stable cyclic performance over repeated adsorption–desorption cycles with minimal capacity loss. These results demonstrate that simple ammonia-based functionalization provides an effective and scalable strategy to enhance CO₂ capture performance and stability of zeolite 5A under practical operating conditions.
- 2 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Nitrogen-Containing Functionalization on CO₂ Capture and Stability of Zeolite 5A in Packed Beds
The development of low-cost and durable adsorbents for post-combustion CO₂ capture remains a critical challenge. In this study, zeolite LTA 5A was modified using aqueous ammonia (NH₄OH) and monoethanolamine (MEA) to examine how nitrogen-containing additives influence surface properties and CO₂ adsorption performance in both powder and granulated forms. Structural and physicochemical characterization (XRD, SEM–EDS, FTIR, BET, and CO₂-TPD) confirmed preservation of the zeolite framework after modification, while spectroscopic and desorption analyses indicated the introduction of nitrogen-containing functionalities. Considering the limitations of EDS for nitrogen quantification, correlations are drawn based on observable changes in surface chemistry and porosity. Functionalization reduced N₂-accessible surface area and pore volume but enhanced CO₂ affinity under dynamic conditions. In fixed-bed breakthrough experiments at ambient conditions with 5 vol.% CO₂, the NH₄OH-modified powder exhibited the highest dynamic capacity (8.8 mmol g⁻¹) and capture efficiency (68%), outperforming unmodified and MEA-treated samples. Additionally, the NH₄OH-functionalized adsorbent demonstrated stable cyclic performance over repeated adsorption–desorption cycles with minimal capacity loss. These results demonstrate that simple ammonia-based functionalization provides an effective and scalable strategy to enhance CO₂ capture performance and stability of zeolite 5A under practical operating conditions.
- 8 August 2024
- Published by Wiley in Biopolymers
- Vol. 115 (6) , e23619
Preparation and Characterization of Durian Husk‐Based Biocomposite Films Reinforced With Nanocellulose From Corn Husk and Pineapple Leaf
This research explores the integration of corn husk nanocellulose (CHNc) and pineapple leaf nanocellulose (PLNc) as reinforcing agents in a carboxymethyl cellulose‐based film derived from durian husk (CMCDH). Through a solvent‐casting method, composite films were fabricated with varying nanocellulose contents (15, 30, and 45 wt%). Analysis using Fourier transform infrared spectroscopy and x‐ray diffraction confirmed the effectiveness of alkaline and bleaching treatments in eliminating noncellulosic components. Transmission electron microscopy image revealed the rod‐like morphology of CHNc and PLNc, with dimensions approximately 206.5 × 7.2 nm and 150.7 × 6.5 nm, respectively. The inclusion of nanocellulose decreased the transparency of CMCDH films while enhancing their tensile strength, thermal stability, and water vapor transmission rate. Notably, CMCDH/PLNc(30%) exhibited the highest tensile strength at 5.06 ± 0.83 MPa, representing a remarkable 220% increase compared to CMCDH biofilm. Thermogravimetric analysis and differential scanning calorimeter results indicated that nanocellulose incorporation delayed the film's decomposition temperature by approximately 10°C. Moreover, CMCDH/PLNc(30%) demonstrated the lowest water vapor transmission rate, marking a 20% improvement. However, the film's properties were compromised at the highest nanocellulose content (45 wt%) due to observed fiber aggregation, as revealed by scanning electron microscopy analysis.
- 8 August 2024
- Published by Wiley in Biopolymers
- Vol. 115 (6) , e23619
Preparation and Characterization of Durian Husk‐Based Biocomposite Films Reinforced With Nanocellulose From Corn Husk and Pineapple Leaf
This research explores the integration of corn husk nanocellulose (CHNc) and pineapple leaf nanocellulose (PLNc) as reinforcing agents in a carboxymethyl cellulose‐based film derived from durian husk (CMCDH). Through a solvent‐casting method, composite films were fabricated with varying nanocellulose contents (15, 30, and 45 wt%). Analysis using Fourier transform infrared spectroscopy and x‐ray diffraction confirmed the effectiveness of alkaline and bleaching treatments in eliminating noncellulosic components. Transmission electron microscopy image revealed the rod‐like morphology of CHNc and PLNc, with dimensions approximately 206.5 × 7.2 nm and 150.7 × 6.5 nm, respectively. The inclusion of nanocellulose decreased the transparency of CMCDH films while enhancing their tensile strength, thermal stability, and water vapor transmission rate. Notably, CMCDH/PLNc(30%) exhibited the highest tensile strength at 5.06 ± 0.83 MPa, representing a remarkable 220% increase compared to CMCDH biofilm. Thermogravimetric analysis and differential scanning calorimeter results indicated that nanocellulose incorporation delayed the film's decomposition temperature by approximately 10°C. Moreover, CMCDH/PLNc(30%) demonstrated the lowest water vapor transmission rate, marking a 20% improvement. However, the film's properties were compromised at the highest nanocellulose content (45 wt%) due to observed fiber aggregation, as revealed by scanning electron microscopy analysis.
- Open Access
- 7 July 2018
- Published by Universitas Gadjah Mada in ASEAN Journal of Chemical Engineering
- Vol. 17 (2) , 60-76
Open Loop Recycling of Recycled Polypropylene for Motorcycle Saddle Application
This research investigated the possibility of using polymer blends of virgin andrecycled polypropylene (PP) for a motorcycle saddle application. Three differentrecycled PPs obtained from different sources contained carbon black (CB). Specimenswere prepared by injection molding for mechanical property testing and colorcharacterization whereas scraps from runners were used for thermal property testing. Itwas found that tensile and flexural properties of recycled PPs were better than those ofvirgin PP due to the fact that recycled PPs contained CB which is a reinforcing material.These properties were improved as the amount of recycled PP added increased. Sincerecycled PPs are strong materials, they are hence brittle resulting in lowering impactstrength and percent elongation. The recycled PP sources and compatibility betweenvirgin and recycled PPs strongly influence the blends' properties. The melt flow index ofthe blends increased as the amount of the recycled PP increased because of the shortpolymer chains of recycled PP resulting from earlier processing. Blending virgin PP withrecycled PP not only improves its properties, but also reduces raw material costs in therange of 5-13%. The advantage of open loop recycling is a wider recycled plasticmarket.
- 7 July 2018
- Published by Universitas Gadjah Mada in ASEAN Journal of Chemical Engineering
- Vol. 17 (2) , 60-76
Open AccessOpen Loop Recycling of Recycled Polypropylene for Motorcycle Saddle Application
This research investigated the possibility of using polymer blends of virgin andrecycled polypropylene (PP) for a motorcycle saddle application. Three differentrecycled PPs obtained from different sources contained carbon black (CB). Specimenswere prepared by injection molding for mechanical property testing and colorcharacterization whereas scraps from runners were used for thermal property testing. Itwas found that tensile and flexural properties of recycled PPs were better than those ofvirgin PP due to the fact that recycled PPs contained CB which is a reinforcing material.These properties were improved as the amount of recycled PP added increased. Sincerecycled PPs are strong materials, they are hence brittle resulting in lowering impactstrength and percent elongation. The recycled PP sources and compatibility betweenvirgin and recycled PPs strongly influence the blends' properties. The melt flow index ofthe blends increased as the amount of the recycled PP increased because of the shortpolymer chains of recycled PP resulting from earlier processing. Blending virgin PP withrecycled PP not only improves its properties, but also reduces raw material costs in therange of 5-13%. The advantage of open loop recycling is a wider recycled plasticmarket.