Jayaprakash Reddy
Research Subjects
Jayaprakash Reddy has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Rudra Pratap
Centre for Nano Science and Engineering
5 shared publications- Anand Natarajan
Department of Mechanical Engineering, College of Engineering Trivandrum, Engineering College P.O, Sreekaryam, Thiruvananathapuram, Kerala, 695016, India / / APJ Abdul Kalam Technological University, Thiruvananathapuram, CET Campus, Thiruvananthapuram Kerala, 695016, India
2 shared publications - K Vijayan
ISRO Inertial Systems Unit, Vattiyoorkavu PO, Thiruvananthapuram, Kerala, 695013, India
2 shared publications - Prasanth Prabhakaran
ISRO Inertial Systems Unit, Vattiyoorkavu PO, Thiruvananthapuram, Kerala, 695013, India
2 shared publications - Ajay Dangi
Department of Biomedical Engineering, Penn State University, University Park, PA 16802, USA
1 shared publication Bijulal D
APJ Abdul Kalam Technological University, Thiruvananathapuram, CET Campus, Thiruvananthapuram Kerala, 695016, India / / Department of Mechanical Engineering, Government Engineering College Barton Hill, Kunnukuzhi, Thiruvananthapuram, Kerala, 695035, India
1 shared publication
Latest Publications
- Open Access
- 19 December 2025
- Published by Szechenyi Istvan University in Acta Technica Jaurinensis
- Vol. 19 (1) , 34-47
Improving wear performance of Mg-4Zn alloy using Si3N4 nanoparticle reinforcements: Mass loss analysis
Si3N4 ceramic possesses superior wear properties and high-temperature properties. This research hypothesizes that very small quantities (0.23, 0.45, and 0.67 wt.%) of the biocompatible, bio-ceramic, Si3N4 nanoparticles (of 15-30 nanometre average particle size) added as reinforcements to the lightweight, biofriendly Mg-4Zn alloy matrix would improve the wear properties of the Mg-4Zn alloy. Hypothesis verification was done using design of experiments (DoE)-based dry sliding wear studies. Mg-4Zn alloy and Mg-4Zn/xSi3N4 (x=0.23, 0.45, and 0.67 wt.% nano-Si3N4) nanocomposites were the pin materials, and SS316Ti was used as the disc (counterface) material. Load and sliding speed were also varied. A regression model for predicting the mass loss was obtained using Design-Expert software. Worn surface analysis revealed that abrasion was the dominating mechanism of wear in all tested conditions. Adhesion wear was also observed at mild levels. The addition of 0.23, 0.45, and 0.67 wt.% nano-Si3N4 to Mg-4Zn alloy refined the grain size by 10.58, 34.32, and 63.94 %, respectively, thereby improving the microhardness by 8.11, 19.54, and 38.67 %, respectively, and reducing the mass loss up to 8.3%. The microstructural studies indicated α-Mg grains surrounded by Mg-Zn intermetallic at the grain boundaries.
- 19 December 2025
- Published by Szechenyi Istvan University in Acta Technica Jaurinensis
- Vol. 19 (1) , 34-47
Open AccessImproving wear performance of Mg-4Zn alloy using Si3N4 nanoparticle reinforcements: Mass loss analysis
Si3N4 ceramic possesses superior wear properties and high-temperature properties. This research hypothesizes that very small quantities (0.23, 0.45, and 0.67 wt.%) of the biocompatible, bio-ceramic, Si3N4 nanoparticles (of 15-30 nanometre average particle size) added as reinforcements to the lightweight, biofriendly Mg-4Zn alloy matrix would improve the wear properties of the Mg-4Zn alloy. Hypothesis verification was done using design of experiments (DoE)-based dry sliding wear studies. Mg-4Zn alloy and Mg-4Zn/xSi3N4 (x=0.23, 0.45, and 0.67 wt.% nano-Si3N4) nanocomposites were the pin materials, and SS316Ti was used as the disc (counterface) material. Load and sliding speed were also varied. A regression model for predicting the mass loss was obtained using Design-Expert software. Worn surface analysis revealed that abrasion was the dominating mechanism of wear in all tested conditions. Adhesion wear was also observed at mild levels. The addition of 0.23, 0.45, and 0.67 wt.% nano-Si3N4 to Mg-4Zn alloy refined the grain size by 10.58, 34.32, and 63.94 %, respectively, thereby improving the microhardness by 8.11, 19.54, and 38.67 %, respectively, and reducing the mass loss up to 8.3%. The microstructural studies indicated α-Mg grains surrounded by Mg-Zn intermetallic at the grain boundaries.
- Open Access
- 28 July 2025
- Published by Szechenyi Istvan University in Acta Technica Jaurinensis
- Vol. 18 (4) , 188-200
Surface roughness, material removal rate, and their multi-objective optimization in the dry turning of Mg-4Zn/Si3N4 nanocomposites by PCD tool
To manufacture useful products with good surface quality from the sustainable Mg-4Zn/Si3N4 nanocomposites strengthened by Si3N4 nanoparticles, machining after stir casting is needed, and it has to be done economically. The Si3N4 nanoparticles could influence the machining behavior due to their abrasive properties and their ability to strengthen the alloy matrix. Multi-objective optimization of material removal rate (MRR) (a good indicator of economic production) and surface roughness (Ra) (a good indicator of quality of surface) are necessary to identify the optimal settings. This research reports the dry turning studies of vacuum stir cast Mg-4Zn/Si3N4 nanocomposites with a polycrystalline diamond turning tool. Response surface methodology (RSM)-based Box-Behnken design was used. The reinforcement (nanometre-sized silicon nitride) weight percentage, cutting speed, feed rate, and depth of cut were the input factors. Regression models for prediction of material removal rate (MRR) and surface roughness (Ra) were obtained and validated. Multi-objective optimization of MRR and Ra using Design-Expert software identified a reinforcement of 0.44 wt.% and a cutting speed of 110 m/min, a feed rate of 0.09 mm/rev, and a depth of cut of 0.16 mm as the optimal settings. The effects of the input process parameters on the MRR and Ra are also studied.
- 28 July 2025
- Published by Szechenyi Istvan University in Acta Technica Jaurinensis
- Vol. 18 (4) , 188-200
Open AccessSurface roughness, material removal rate, and their multi-objective optimization in the dry turning of Mg-4Zn/Si3N4 nanocomposites by PCD tool
To manufacture useful products with good surface quality from the sustainable Mg-4Zn/Si3N4 nanocomposites strengthened by Si3N4 nanoparticles, machining after stir casting is needed, and it has to be done economically. The Si3N4 nanoparticles could influence the machining behavior due to their abrasive properties and their ability to strengthen the alloy matrix. Multi-objective optimization of material removal rate (MRR) (a good indicator of economic production) and surface roughness (Ra) (a good indicator of quality of surface) are necessary to identify the optimal settings. This research reports the dry turning studies of vacuum stir cast Mg-4Zn/Si3N4 nanocomposites with a polycrystalline diamond turning tool. Response surface methodology (RSM)-based Box-Behnken design was used. The reinforcement (nanometre-sized silicon nitride) weight percentage, cutting speed, feed rate, and depth of cut were the input factors. Regression models for prediction of material removal rate (MRR) and surface roughness (Ra) were obtained and validated. Multi-objective optimization of MRR and Ra using Design-Expert software identified a reinforcement of 0.44 wt.% and a cutting speed of 110 m/min, a feed rate of 0.09 mm/rev, and a depth of cut of 0.16 mm as the optimal settings. The effects of the input process parameters on the MRR and Ra are also studied.
- 17 April 2021
- Published by Springer Nature in ISSS Journal of Micro and Smart Systems
- Vol. 10 (1) , 1-6
A method for realizing robust micro-scale electromagnetic actuators for high current density applications
- 17 April 2021
- Published by Springer Nature in ISSS Journal of Micro and Smart Systems
- Vol. 10 (1) , 1-6
A method for realizing robust micro-scale electromagnetic actuators for high current density applications
- 25 September 2018
- Published by Springer Nature in ISSS Journal of Micro and Smart Systems
- Vol. 7 (2) , 87-96
Design, fabrication and on-the-die characterization of a MEMS tuning-fork gyroscope
- 25 September 2018
- Published by Springer Nature in ISSS Journal of Micro and Smart Systems
- Vol. 7 (2) , 87-96
Design, fabrication and on-the-die characterization of a MEMS tuning-fork gyroscope
- Open Access
- 18 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 345
Cricket Inspired High Efficiency MEMS Speakers
We report on the realization of a biomimetic MEMS speaker inspired by field crickets. This speaker is at least five times thinner and four times more efficient than the current dynamic speakers used in portable electronics. We present results of the acoustic characterization of a single MEMS speaker. Computational extrapolation of the results suggests that an array of such thin speakers will be highly efficient compared to the existing speakers of equal area.
- 18 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 345
Open AccessCricket Inspired High Efficiency MEMS Speakers
We report on the realization of a biomimetic MEMS speaker inspired by field crickets. This speaker is at least five times thinner and four times more efficient than the current dynamic speakers used in portable electronics. We present results of the acoustic characterization of a single MEMS speaker. Computational extrapolation of the results suggests that an array of such thin speakers will be highly efficient compared to the existing speakers of equal area.
- 25 October 2016
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 27 (1) , 015005
Si-gold-glass hybrid wafer bond for 3D-MEMS and wafer level packaging
We report a relatively low temperature (<400 °C) hybrid wafer bonding process that results in the simultaneous anodic and eutectic bonding in different predetermined regions of the wafer. This hybrid bonding process has potential applications in CMOS-MEMS device integration and wafer level packaging. We demonstrate the process by realizing a simple MEMS cantilever beam and a complex MEMS gyroscope structure. These structures are characterized for ohmic contact and electromechanical response to verify the electrical interconnect and the mechanical strength of the structure at the bond interface.
- 25 October 2016
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 27 (1) , 015005
Si-gold-glass hybrid wafer bond for 3D-MEMS and wafer level packaging
We report a relatively low temperature (<400 °C) hybrid wafer bonding process that results in the simultaneous anodic and eutectic bonding in different predetermined regions of the wafer. This hybrid bonding process has potential applications in CMOS-MEMS device integration and wafer level packaging. We demonstrate the process by realizing a simple MEMS cantilever beam and a complex MEMS gyroscope structure. These structures are characterized for ohmic contact and electromechanical response to verify the electrical interconnect and the mechanical strength of the structure at the bond interface.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Fabrication of stress-free MEMS structures with a modified SOI-on-glass
We report the successful implementation of a modified SOI-on-Glass fabrication process that greatly facilitates realization of stress-free MEMS structures suspended over small gaps, especially useful for capacitive transduction. The key modification is in patterning the capacitive gap in the SOI and patterning the structural layer before bonding the SOI to glass wafer. We demonstrate the process by realizing a doubly clamped beam, an accelerometer, a capacitive micromachined ultrasound transducer, and a Coriolis vibratory gyroscope structure. These MEMS structures are characterized for their stiffness and dynamic response. The experimental results are compared with FEM simulation for frequency response and stiffness. It is observed that the values are in close agreement with simulated results for stress-free structures errors less than 4%, demonstrating that the modified process flow indeed results in stress-free MEMS structures.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Fabrication of stress-free MEMS structures with a modified SOI-on-glass
We report the successful implementation of a modified SOI-on-Glass fabrication process that greatly facilitates realization of stress-free MEMS structures suspended over small gaps, especially useful for capacitive transduction. The key modification is in patterning the capacitive gap in the SOI and patterning the structural layer before bonding the SOI to glass wafer. We demonstrate the process by realizing a doubly clamped beam, an accelerometer, a capacitive micromachined ultrasound transducer, and a Coriolis vibratory gyroscope structure. These MEMS structures are characterized for their stiffness and dynamic response. The experimental results are compared with FEM simulation for frequency response and stiffness. It is observed that the values are in close agreement with simulated results for stress-free structures errors less than 4%, demonstrating that the modified process flow indeed results in stress-free MEMS structures.
- 21 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 24 (6) , 1712-1719
A Study of Pressure-Dependent Squeeze Film Stiffness as a Resonance Modulator Using Static and Dynamic Measurements
We report on the resonant frequency modulation of inertial microelectromechanical systems (MEMS) structures due to squeeze film stiffness over a range of working pressures. Squeeze film effects have been studied extensively, but mostly in the context of damping and Q-factor determination of dynamic MEMS structures, typically suspended over a fixed substrate with a very thin air gap. Here, we show with experimental measurements and analytical calculations how the pressure-dependent air springs (squeeze film stiffness) change the resonant frequency of an inertial MEMS structure by as much as five times. For capturing the isolated effect of the squeeze film stiffness, we first determine the static stiffness of our structure with atomic force microscope probing and then study the effect of the air spring by measuring the dynamic response of the structure, thus handing the resonant frequencies while varying the air pressure from 1 to 905 mbar. We also verify our results by analytical and Finite Element Method calculations. Our findings show that the pressure-dependent squeeze film stiffness can affect a rather huge range of frequency modulation (>400%) and, therefore, can be used as a design parameter for exploiting this effect in MEMS devices.
- 21 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 24 (6) , 1712-1719
A Study of Pressure-Dependent Squeeze Film Stiffness as a Resonance Modulator Using Static and Dynamic Measurements
We report on the resonant frequency modulation of inertial microelectromechanical systems (MEMS) structures due to squeeze film stiffness over a range of working pressures. Squeeze film effects have been studied extensively, but mostly in the context of damping and Q-factor determination of dynamic MEMS structures, typically suspended over a fixed substrate with a very thin air gap. Here, we show with experimental measurements and analytical calculations how the pressure-dependent air springs (squeeze film stiffness) change the resonant frequency of an inertial MEMS structure by as much as five times. For capturing the isolated effect of the squeeze film stiffness, we first determine the static stiffness of our structure with atomic force microscope probing and then study the effect of the air spring by measuring the dynamic response of the structure, thus handing the resonant frequencies while varying the air pressure from 1 to 905 mbar. We also verify our results by analytical and Finite Element Method calculations. Our findings show that the pressure-dependent squeeze film stiffness can affect a rather huge range of frequency modulation (>400%) and, therefore, can be used as a design parameter for exploiting this effect in MEMS devices.
- 1 March 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 141-144
Coupled numerical analysis of Suspended gate field effect transistor (SGFET)
Suspended gate MOSFETs exist since last few decades. Resonant gate transistors were first demonstrated as a means of getting high Q devices [1]. The advantages of transistor based transduction as compared to the capacitive detection have also been demonstrated [2,3]. The behaviors of SGFETs have been studied using equivalent lumped parameter modeling methodology [4–7]. Numerical simulations involving “hybrid” FEA coupling between two different tools, ANSYS Multiphysics and ISE-DESIS, with the help of an external Perl script have also been tried [8]. Here ANSYS is used for the coupled electrostatic and structural physics calculations and ISE-DESIS provides the correct boundary conditions for the electrostatic domain using semiconductor physics. Another related study [9] solved the beam equation coupled with the Poisson equation numerically using finite difference and Newton Raphson method. Our work presents an easier modeling and analysis of a suspended gate MOSFET in COMSOL, successfully demonstrating a solution of a moving gate type device. In our analysis, we consider the air gap as a deformable continuum and we report the standard Id-Vg characteristics of the transistor. Commercially available packages such as ISE-DESIS specialize in only fixed gap analysis wherein air is also modeled as a material with a known permittivity. In such an analysis the capacitor formed due to the air gap remains fixed. We demonstrate here that this analysis can be easily carried out in COMSOL using its multiphysics features. Using two dimensional analysis involving structural mechanics domain, moving mesh ALE, convection and diffusion, and the electrostatics domain, the effect of moving gate and hence the moving air gap can be modeled and analyzed.
- 1 March 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 141-144
Coupled numerical analysis of Suspended gate field effect transistor (SGFET)
Suspended gate MOSFETs exist since last few decades. Resonant gate transistors were first demonstrated as a means of getting high Q devices [1]. The advantages of transistor based transduction as compared to the capacitive detection have also been demonstrated [2,3]. The behaviors of SGFETs have been studied using equivalent lumped parameter modeling methodology [4–7]. Numerical simulations involving “hybrid” FEA coupling between two different tools, ANSYS Multiphysics and ISE-DESIS, with the help of an external Perl script have also been tried [8]. Here ANSYS is used for the coupled electrostatic and structural physics calculations and ISE-DESIS provides the correct boundary conditions for the electrostatic domain using semiconductor physics. Another related study [9] solved the beam equation coupled with the Poisson equation numerically using finite difference and Newton Raphson method. Our work presents an easier modeling and analysis of a suspended gate MOSFET in COMSOL, successfully demonstrating a solution of a moving gate type device. In our analysis, we consider the air gap as a deformable continuum and we report the standard Id-Vg characteristics of the transistor. Commercially available packages such as ISE-DESIS specialize in only fixed gap analysis wherein air is also modeled as a material with a known permittivity. In such an analysis the capacitor formed due to the air gap remains fixed. We demonstrate here that this analysis can be easily carried out in COMSOL using its multiphysics features. Using two dimensional analysis involving structural mechanics domain, moving mesh ALE, convection and diffusion, and the electrostatics domain, the effect of moving gate and hence the moving air gap can be modeled and analyzed.