K Vijayan
Research Subjects
Research Interests
K Vijayan has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Anand Natarajan
Department of Mechanical Engineering, College of Engineering Trivandrum, Engineering College P.O, Sreekaryam, Thiruvananathapuram, Kerala, 695016, India / / APJ Abdul Kalam Technological University, Thiruvananathapuram, CET Campus, Thiruvananthapuram Kerala, 695016, India
2 shared publications - Jayaprakash Reddy
ISRO Inertial Systems Unit, Vattiyoorkavu PO, Thiruvananthapuram, Kerala, 695013, India
2 shared publications - Prasanth Prabhakaran
ISRO Inertial Systems Unit, Vattiyoorkavu PO, Thiruvananthapuram, Kerala, 695013, India
2 shared publications Bijulal D
APJ Abdul Kalam Technological University, Thiruvananathapuram, CET Campus, Thiruvananthapuram Kerala, 695016, India / / Department of Mechanical Engineering, Government Engineering College Barton Hill, Kunnukuzhi, Thiruvananthapuram, Kerala, 695035, India
1 shared publication- Dharmaseelan Bijulal
Department of Mechanical Engineering, Government Engineering College Barton Hill, Kunnukuzhi, Thiruvananthapuram 695035, Kerala State, India
1 shared publication - Ramu Kumar Verma
ISRO Inertial Systems Unit, Vattiyoorkavu PO, Thiruvananthapuram, Kerala, 695013, India
1 shared publication
Latest Publications
- Open Access
- 19 December 2025
- Published by Szechenyi Istvan University in Acta Technica Jaurinensis
- Vol. 19 (1) , 34-47
Improving wear performance of Mg-4Zn alloy using Si3N4 nanoparticle reinforcements: Mass loss analysis
Si3N4 ceramic possesses superior wear properties and high-temperature properties. This research hypothesizes that very small quantities (0.23, 0.45, and 0.67 wt.%) of the biocompatible, bio-ceramic, Si3N4 nanoparticles (of 15-30 nanometre average particle size) added as reinforcements to the lightweight, biofriendly Mg-4Zn alloy matrix would improve the wear properties of the Mg-4Zn alloy. Hypothesis verification was done using design of experiments (DoE)-based dry sliding wear studies. Mg-4Zn alloy and Mg-4Zn/xSi3N4 (x=0.23, 0.45, and 0.67 wt.% nano-Si3N4) nanocomposites were the pin materials, and SS316Ti was used as the disc (counterface) material. Load and sliding speed were also varied. A regression model for predicting the mass loss was obtained using Design-Expert software. Worn surface analysis revealed that abrasion was the dominating mechanism of wear in all tested conditions. Adhesion wear was also observed at mild levels. The addition of 0.23, 0.45, and 0.67 wt.% nano-Si3N4 to Mg-4Zn alloy refined the grain size by 10.58, 34.32, and 63.94 %, respectively, thereby improving the microhardness by 8.11, 19.54, and 38.67 %, respectively, and reducing the mass loss up to 8.3%. The microstructural studies indicated α-Mg grains surrounded by Mg-Zn intermetallic at the grain boundaries.
- 19 December 2025
- Published by Szechenyi Istvan University in Acta Technica Jaurinensis
- Vol. 19 (1) , 34-47
Open AccessImproving wear performance of Mg-4Zn alloy using Si3N4 nanoparticle reinforcements: Mass loss analysis
Si3N4 ceramic possesses superior wear properties and high-temperature properties. This research hypothesizes that very small quantities (0.23, 0.45, and 0.67 wt.%) of the biocompatible, bio-ceramic, Si3N4 nanoparticles (of 15-30 nanometre average particle size) added as reinforcements to the lightweight, biofriendly Mg-4Zn alloy matrix would improve the wear properties of the Mg-4Zn alloy. Hypothesis verification was done using design of experiments (DoE)-based dry sliding wear studies. Mg-4Zn alloy and Mg-4Zn/xSi3N4 (x=0.23, 0.45, and 0.67 wt.% nano-Si3N4) nanocomposites were the pin materials, and SS316Ti was used as the disc (counterface) material. Load and sliding speed were also varied. A regression model for predicting the mass loss was obtained using Design-Expert software. Worn surface analysis revealed that abrasion was the dominating mechanism of wear in all tested conditions. Adhesion wear was also observed at mild levels. The addition of 0.23, 0.45, and 0.67 wt.% nano-Si3N4 to Mg-4Zn alloy refined the grain size by 10.58, 34.32, and 63.94 %, respectively, thereby improving the microhardness by 8.11, 19.54, and 38.67 %, respectively, and reducing the mass loss up to 8.3%. The microstructural studies indicated α-Mg grains surrounded by Mg-Zn intermetallic at the grain boundaries.
- Open Access
- 28 July 2025
- Published by Szechenyi Istvan University in Acta Technica Jaurinensis
- Vol. 18 (4) , 188-200
Surface roughness, material removal rate, and their multi-objective optimization in the dry turning of Mg-4Zn/Si3N4 nanocomposites by PCD tool
To manufacture useful products with good surface quality from the sustainable Mg-4Zn/Si3N4 nanocomposites strengthened by Si3N4 nanoparticles, machining after stir casting is needed, and it has to be done economically. The Si3N4 nanoparticles could influence the machining behavior due to their abrasive properties and their ability to strengthen the alloy matrix. Multi-objective optimization of material removal rate (MRR) (a good indicator of economic production) and surface roughness (Ra) (a good indicator of quality of surface) are necessary to identify the optimal settings. This research reports the dry turning studies of vacuum stir cast Mg-4Zn/Si3N4 nanocomposites with a polycrystalline diamond turning tool. Response surface methodology (RSM)-based Box-Behnken design was used. The reinforcement (nanometre-sized silicon nitride) weight percentage, cutting speed, feed rate, and depth of cut were the input factors. Regression models for prediction of material removal rate (MRR) and surface roughness (Ra) were obtained and validated. Multi-objective optimization of MRR and Ra using Design-Expert software identified a reinforcement of 0.44 wt.% and a cutting speed of 110 m/min, a feed rate of 0.09 mm/rev, and a depth of cut of 0.16 mm as the optimal settings. The effects of the input process parameters on the MRR and Ra are also studied.
- 28 July 2025
- Published by Szechenyi Istvan University in Acta Technica Jaurinensis
- Vol. 18 (4) , 188-200
Open AccessSurface roughness, material removal rate, and their multi-objective optimization in the dry turning of Mg-4Zn/Si3N4 nanocomposites by PCD tool
To manufacture useful products with good surface quality from the sustainable Mg-4Zn/Si3N4 nanocomposites strengthened by Si3N4 nanoparticles, machining after stir casting is needed, and it has to be done economically. The Si3N4 nanoparticles could influence the machining behavior due to their abrasive properties and their ability to strengthen the alloy matrix. Multi-objective optimization of material removal rate (MRR) (a good indicator of economic production) and surface roughness (Ra) (a good indicator of quality of surface) are necessary to identify the optimal settings. This research reports the dry turning studies of vacuum stir cast Mg-4Zn/Si3N4 nanocomposites with a polycrystalline diamond turning tool. Response surface methodology (RSM)-based Box-Behnken design was used. The reinforcement (nanometre-sized silicon nitride) weight percentage, cutting speed, feed rate, and depth of cut were the input factors. Regression models for prediction of material removal rate (MRR) and surface roughness (Ra) were obtained and validated. Multi-objective optimization of MRR and Ra using Design-Expert software identified a reinforcement of 0.44 wt.% and a cutting speed of 110 m/min, a feed rate of 0.09 mm/rev, and a depth of cut of 0.16 mm as the optimal settings. The effects of the input process parameters on the MRR and Ra are also studied.