Ali Kahirdeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ali Kahirdeh has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
M.M. Khonsari
3 shared publications- Christine M. Sauerbrunn
Center for Risk and Reliability, University of Maryland, College Park, MD 20742, USA
1 shared publication M Naderi
Department of Mechanical Engineering, Louisiana State University, LA, USA
1 shared publicationM. Naderi
1 shared publication- Michael M. Khonsari
Department of Mechanical Engineering and Industrial Engineering, Louisiana State University, Baton Rouge, LA 70803, USA
1 shared publication Mm Khonsari
Department of Mechanical Engineering, Louisiana State University, LA, USA
1 shared publication
Latest Publications
- Open Access
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1757 (1) , 060007
Acoustic emission entropy as a measure of damage in materials
In this paper, we propose the information entropy of acoustic emission (AE) signatures as an index for assessment of degradation in materials. This is a new method for health monitoring of materials and structures that relies on the estimation of the information entropy from the AE signals detected, for example from cyclic fatigue loading of the materials. Different ways of calculation of the information entropy from AE signals are explored and discussed in this paper. As an example of the materials degradation, this study investigates the behavior of maximum entropy (S max ) at the time of the materials’ failure using a series of fatigue cracking tests on titanium alloy, a material commonly used in certain aircraft structures. This paper describes the fatigue tests in which AE waves and features were measured and discusses the various approaches to estimate the information entropy corresponding to the detected AE. The results show that fatigue failure occurs at the same maximum entropy value regardless of the trajectory of the fatigue crack growth and loading conditions that caused the fatigue.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1757 (1) , 060007
Open AccessAcoustic emission entropy as a measure of damage in materials
In this paper, we propose the information entropy of acoustic emission (AE) signatures as an index for assessment of degradation in materials. This is a new method for health monitoring of materials and structures that relies on the estimation of the information entropy from the AE signals detected, for example from cyclic fatigue loading of the materials. Different ways of calculation of the information entropy from AE signals are explored and discussed in this paper. As an example of the materials degradation, this study investigates the behavior of maximum entropy (S max ) at the time of the materials’ failure using a series of fatigue cracking tests on titanium alloy, a material commonly used in certain aircraft structures. This paper describes the fatigue tests in which AE waves and features were measured and discusses the various approaches to estimate the information entropy corresponding to the detected AE. The results show that fatigue failure occurs at the same maximum entropy value regardless of the trajectory of the fatigue crack growth and loading conditions that caused the fatigue.
- 1 December 2015
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 77, 74-85
Energy dissipation in the course of the fatigue degradation: Mathematical derivation and experimental quantification
- 1 December 2015
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 77, 74-85
Energy dissipation in the course of the fatigue degradation: Mathematical derivation and experimental quantification
- 1 May 2014
- Published by Elsevier in Composites Part B: Engineering
- Vol. 61, 375-382
Criticality of degradation in composite materials subjected to cyclic loading
- 1 May 2014
- Published by Elsevier in Composites Part B: Engineering
- Vol. 61, 375-382
Criticality of degradation in composite materials subjected to cyclic loading
- 4 July 2012
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 47 (15) , 1803-1815
On the role of cooling on fatigue failure of a woven glass/epoxy laminate
The effect of the surface cooling on the fatigue life of a glass/epoxy laminate during fully reversed bending tests is investigated both experimentally and analytically. The experimental tests involve the use of acoustic emission and infrared thermography to monitor the structural integrity and evolution of damage. An analytical study is also performed to calculate the stress in the outermost layer of the laminate for both cases of cooled and uncooled specimens. The results show that the life of the laminate is highly dependent on the temperature and that surface cooling, if done appropriately, can significantly increase the fatigue life of the laminate.
- 4 July 2012
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 47 (15) , 1803-1815
On the role of cooling on fatigue failure of a woven glass/epoxy laminate
The effect of the surface cooling on the fatigue life of a glass/epoxy laminate during fully reversed bending tests is investigated both experimentally and analytically. The experimental tests involve the use of acoustic emission and infrared thermography to monitor the structural integrity and evolution of damage. An analytical study is also performed to calculate the stress in the outermost layer of the laminate for both cases of cooled and uncooled specimens. The results show that the life of the laminate is highly dependent on the temperature and that surface cooling, if done appropriately, can significantly increase the fatigue life of the laminate.
- Top Cited Papers
- 1 April 2012
- Published by Elsevier in Composites Part B: Engineering
- Vol. 43 (3) , 1613-1620
Dissipated thermal energy and damage evolution of Glass/Epoxy using infrared thermography and acoustic emission
- 1 April 2012
- Published by Elsevier in Composites Part B: Engineering
- Vol. 43 (3) , 1613-1620
Top Cited PapersDissipated thermal energy and damage evolution of Glass/Epoxy using infrared thermography and acoustic emission
- 1 October 2010
- Published by ASME International in Journal of Tribology
- Vol. 132 (4) , 041606
Condition Monitoring of Molybdenum Disulphide Coated Thrust Ball Bearings Using Time-Frequency Signal Analysis
A method for detection of wear in thrust ball bearings coated with molybdenum disulphide is presented. It employs an energy feature obtained from time-frequency representation of the vibration signal. Extensive experimental studies are conducted to verify the efficacy of the proposed method for fault diagnosis of coating. These experiments are conducted under both oscillatory and unidirectional motions. The results of vibrations are corroborated with the friction coefficient from the onset of the motion until failure develops. Through monitoring of the energy in time-frequency domain as well as the coefficient of friction, three stages of coating life are identified. They are healthy period, developing damage, and failure. It is shown that the energy feature can detect whenever wear and damage appear and solid lubricant loses its lubrication capabilities.- 1 October 2010
- Published by ASME International in Journal of Tribology
- Vol. 132 (4) , 041606
Condition Monitoring of Molybdenum Disulphide Coated Thrust Ball Bearings Using Time-Frequency Signal Analysis
A method for detection of wear in thrust ball bearings coated with molybdenum disulphide is presented. It employs an energy feature obtained from time-frequency representation of the vibration signal. Extensive experimental studies are conducted to verify the efficacy of the proposed method for fault diagnosis of coating. These experiments are conducted under both oscillatory and unidirectional motions. The results of vibrations are corroborated with the friction coefficient from the onset of the motion until failure develops. Through monitoring of the energy in time-frequency domain as well as the coefficient of friction, three stages of coating life are identified. They are healthy period, developing damage, and failure. It is shown that the energy feature can detect whenever wear and damage appear and solid lubricant loses its lubrication capabilities.