Alexander Verl
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexander Verl has a total of 181 co-authors. Here are the top co-authors by number of shared publications:
- Armin Lechler
Institute for Control Engineering of Machine Tools and Manufacturing Units (ISW), University of Stuttgart, Stuttgart, Germany
19 shared publications - Michael Neubauer
Montana State University
9 shared publications - Christoph Hinze
Institute for Control Engineering of Machine Tools and Manufacturing Units, University of Stuttgart, Stuttgart, Germany
8 shared publications Armin Lechler
6 shared publications- Colin Reiff
Institute for Control Engineering of Machine Tools and Manufacturing Units (ISW), University of Stuttgart, Seidenstr. 36, 70174 Stuttgart, Germany
5 shared publications - Jaspreet Singh Dhupia
Department of Mechanical and Mechatronics Engineering, The University of Auckland, Auckland, New Zealand
5 shared publications
Latest Publications
- 7 October 2026
- Published by Springer Nature
- p. 407-414
Sustainable Mineral Structures: Lines of Research on Circular and Bio-Based 3D Printing Processes
- 7 October 2026
- Published by Springer Nature
- p. 407-414
Sustainable Mineral Structures: Lines of Research on Circular and Bio-Based 3D Printing Processes
- Open Access
- 1 July 2026
- Published by Springer Nature
- p. 415-423
Moving Towards Continuous Virtual Commissioning Using Open Interfaces for Industrial Robot Integration and Control
The increasing demand for flexible control and simulation concepts in the industry is driven by competitive pressures and shorter product life cycles. Virtual Commissioning (VC) offers the advantage of identifying design and planning errors before the system is commissioned in a real environment. In VC, the test configurations are referred to as Model-in-the-Loop (MiL), Software-in-the-Loop (SiL), and Hardware-in-the-Loop (HiL). The current approach of the different test configurations requires in addition to the organizational preparation and integration, technical efforts such as manual switching and setup. Therefore, this study applies a switching, conversion and transfer mechanism with open interfaces, which enable Continuous Virtual Commissioning (CVC). These mechanisms are tested on an industrial robot cell. This lays the technological foundation for flexible switching between the configurations of VC. Furthermore, robotic joint and cartesian position deviations are observed across the configurations of VC, indicating configuration-specific alterations.
- 1 July 2026
- Published by Springer Nature
- p. 415-423
Open AccessMoving Towards Continuous Virtual Commissioning Using Open Interfaces for Industrial Robot Integration and Control
The increasing demand for flexible control and simulation concepts in the industry is driven by competitive pressures and shorter product life cycles. Virtual Commissioning (VC) offers the advantage of identifying design and planning errors before the system is commissioned in a real environment. In VC, the test configurations are referred to as Model-in-the-Loop (MiL), Software-in-the-Loop (SiL), and Hardware-in-the-Loop (HiL). The current approach of the different test configurations requires in addition to the organizational preparation and integration, technical efforts such as manual switching and setup. Therefore, this study applies a switching, conversion and transfer mechanism with open interfaces, which enable Continuous Virtual Commissioning (CVC). These mechanisms are tested on an industrial robot cell. This lays the technological foundation for flexible switching between the configurations of VC. Furthermore, robotic joint and cartesian position deviations are observed across the configurations of VC, indicating configuration-specific alterations.
- Open Access
- 11 June 2026
- Published by Elsevier in CIRP Annals
- Vol. 75 (2) , 919-942
Digital twins for machine tools
- 11 June 2026
- Published by Elsevier in CIRP Annals
- Vol. 75 (2) , 919-942
Open AccessDigital twins for machine tools
- Open Access
- 18 April 2026
- Published by Elsevier in Journal of Engineering Research
- Vol. 14 (3) , 3355-3363
Use cases for Manufacturing-X: Benefits of data spaces in industrial practice
- 18 April 2026
- Published by Elsevier in Journal of Engineering Research
- Vol. 14 (3) , 3355-3363
Open AccessUse cases for Manufacturing-X: Benefits of data spaces in industrial practice
- Open Access
- 12 April 2026
- Published by Association for Computing Machinery (ACM)
- p. 1-9
A Software Architecture for Real-Time Digital Twins in Machining
- 12 April 2026
- Published by Association for Computing Machinery (ACM)
- p. 1-9
Open AccessA Software Architecture for Real-Time Digital Twins in Machining
- Open Access
- 13 March 2026
- Published by Association for Computing Machinery (ACM)
- p. 44-50
Evaluation of Sliding-Mode Position Controllers on Multi-Axis Machine Tools with Compliant Mechanics
- 13 March 2026
- Published by Association for Computing Machinery (ACM)
- p. 44-50
Open AccessEvaluation of Sliding-Mode Position Controllers on Multi-Axis Machine Tools with Compliant Mechanics
- 2 January 2026
- Published by Springer Nature
- p. 3-15
Enhancing Enquiry Response Efficiency: Methods for Article Data Extraction in Manufacturing
- 2 January 2026
- Published by Springer Nature
- p. 3-15
Enhancing Enquiry Response Efficiency: Methods for Article Data Extraction in Manufacturing
- 30 October 2025
- Published by Springer Nature
- p. 252-263
External Torque Estimation in an Industrial Robot Joint Using Moving-Horizon-Estimation
- 30 October 2025
- Published by Springer Nature
- p. 252-263
External Torque Estimation in an Industrial Robot Joint Using Moving-Horizon-Estimation
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
Towards Automated or Assisted Requirements Extraction and Analysis Using an LLM-Based Multi-Agent System: A Case Study
The increasing variety and complexity of products presents companies with ever greater challenges when selecting and engineering suitable components and systems. A pivotal step in this process is the collection and documentation of requirements, which is conducted manually, necessitating substantial resources, particularly when the underlying data is in unstructured formats. In this publication, we propose an innovative approach to address this issue. Specifically, we present a multi-agent system that is developed based on large language models. This system facilitates the automated or at least assisted analysis of requirements extracted from unstructured data, with a particular emphasis on the processing of text and image data. Initial results show that the approach presented delivers promising results.
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
Towards Automated or Assisted Requirements Extraction and Analysis Using an LLM-Based Multi-Agent System: A Case Study
The increasing variety and complexity of products presents companies with ever greater challenges when selecting and engineering suitable components and systems. A pivotal step in this process is the collection and documentation of requirements, which is conducted manually, necessitating substantial resources, particularly when the underlying data is in unstructured formats. In this publication, we propose an innovative approach to address this issue. Specifically, we present a multi-agent system that is developed based on large language models. This system facilitates the automated or at least assisted analysis of requirements extracted from unstructured data, with a particular emphasis on the processing of text and image data. Initial results show that the approach presented delivers promising results.
- 27 May 2025
- Published by Elsevier in CIRP Annals
- Vol. 74 (1) , 483-486
Automatic preload adjustment for ball screw drives by means of a spring-loaded mechanism
- 27 May 2025
- Published by Elsevier in CIRP Annals
- Vol. 74 (1) , 483-486
Automatic preload adjustment for ball screw drives by means of a spring-loaded mechanism