YJYing Jiang

Ying Jiang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ying Jiang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:

  • Jie Zeng

    State Key Laboratory of Mechanics and Control of Mechanical Structures, Nanjing University of Aeronautics and Astronautics, 210016 Nanjing, China

    3 shared publications
  • Da-Kai Liang

    State Key Laboratory of Mechanics and Control of Mechanical Structures, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

    2 shared publications
  • Dakai Liang

    State Key Laboratory of Mechanics and Control of Mechanical Structures, Nanjing University of Aeronautics and Astronautics, 210016 Nanjing, China

    2 shared publications
  • Mengqi Zhang

    College of Mechanical and Electronic Engineering Nanjing Forestry University No.159 Longpan Road Nanjing People's Republic of China

    2 shared publications
  • Mingjin Yu

    College of Mechanical and Electronic Engineering, Nanjing Forestry University, Nanjing, China

    2 shared publications
  • Xiao-Yu Ni

    2 shared publications

Latest Publications

  • Open Access

    YOLOv7-RAR for Urban Vehicle Detection

    by Yuan Zhang, Youpeng Sun, Zheng Wang, Ying Jiang

    Aiming at the problems of high missed detection rates of the YOLOv7 algorithm for vehicle detection on urban roads, weak perception of small targets in perspective, and insufficient feature extraction, the YOLOv7-RAR recognition algorithm is proposed. The algorithm is improved from the following three directions based on YOLOv7. Firstly, in view of the insufficient nonlinear feature fusion of the original backbone network, the Res3Unit structure is used to reconstruct the backbone network of YOLOv7 to improve the ability of the network model architecture to obtain more nonlinear features. Secondly, in view of the problem that there are many interference backgrounds in urban roads and that the original network is weak in positioning targets such as vehicles, a plug-and-play hybrid attention mechanism module, ACmix, is added after the SPPCSPC layer of the backbone network to enhance the network’s attention to vehicles and reduce the interference of other targets. Finally, aiming at the problem that the receptive field of the original network Narrows, with the deepening of the network model, leads to a high miss rate of small targets, the Gaussian receptive field scheme used in the RFLA (Gaussian-receptive-field-based label assignment) module is used at the connection between the feature fusion area and the detection head to improve the receptive field of the network model for small objects in the image. Combining the three improvement measures, the first letter of the name of each improvement measure is selected, and the improved algorithm is named the YOLOv7-RAR algorithm. Experiments show that on urban roads with crowded vehicles and different weather patterns, the average detection accuracy of the YOLOv7-RAR algorithm reaches 95.1%, which is 2.4% higher than that of the original algorithm; the AP50:90 performance is 12.6% higher than that of the original algorithm. The running speed of the YOLOv7-RAR algorithm reaches 96 FPS, which meets the real-time requirements of vehicle detection; hence, the algorithm can be better applied to vehicle detection.


  • Open Access

    Influence of light source on the strain sensitivity of a polarisation maintaining fibre loop mirror based on voltage demodulation

    by Ying Jiang, Mengqi Zhang

    The sensitivity is an important performance for a polarisation maintaining fibre (PMF) loop mirror (PM‐FLM) sensor based on voltage demodulation. This paper investigates the method of improving the strain sensitivity of a PM‐FLM based on voltage demodulation, including the demodulation principle, the derivation of the output light power equation, and experimentally studies on the strain sensitivity of a PM‐FLM with different narrow‐band input light source. The results show that the PM‐FLM using a high‐power light source as input has a high strain sensitivity but a small linear range of strain measurement, and the PM‐FLM using a low‐power light source as input has a low strain sensitivity but a large linear range of strain measurement. Hence, a high‐power narrow‐band light source as input can be chosen to improve the strain sensitivity, and the authors can also reduce the input light source power to enlarge the linear range of strain measurement.

  • Open Access

    Influence of light source on the sensitivity of a Polarization Maintaining Fiber Loop Mirror vibration sensor

    by Ying Jiang, Mingjin Yu, Mengqi Zhang, Jiyun Lu

    Wavelength or light intensity demodulation method for a polarization maintaining fiber loop mirror (PM-FLM) sensor is not only expensive but also unsuitable for vibration monitoring. This paper studies the voltage demodulation principle and explores theoretically the influence of light source on the sensitivity. Then a PM-FLM sensor is applied to vibration monitoring. A low-power narrow-band light source reflected from FBG and a high-power laser light source are used respectively as input. The time domain voltage signals of vibration from a photo-detector are collected by a data acquisition card and converted via a fast Fourier transform algorithm. The experimental result shows that a PM-FLM sensor using a high-power narrow-band light source as input has a higher sensitivity to vibration than the one using a low-power narrow-band light source. In practical application, we can choose a high-power narrow-band light source as input to improve the sensitivity to vibration.


  • Open Access

    Influence of birefringence fibre length on demodulation sensitivity based on a fibre loop mirror sensor

    by Ying Jiang, Mingjin Yu

    The influence of birefringence fibre (BF) loop mirror (Bi‐FLM) length on the light intensity sensitivity to strain was analysed theoretically and investigated experimentally. The same type of BF but the different length was chosen as the sensing element to be glued to the test object. The relationship between the light intensity and strain was obtained for the Bi‐FLM with different BF length. Afterwards, the light intensity signals were converted into voltage signals. The influence of BF length on the average voltage sensitivity to strain was investigated experimentally. The experimental results indicate that the Bi‐FLM with a long BF has a high average voltage sensitivity to strain but a small strain measurement range, while the Bi‐FLM with a short BF has a low average voltage sensitivity to strain but a large strain measurement range. From the experiments carried out, it was seen that the average voltage sensitivity to strain can be improved by increasing the BF length. This method does not increase the system complexity.


  • The influences of polarization-maintaining fiber length and sensing length on axial strain sensitivity of polarization-maintaining fiber loop mirror

    by Ying Jiang, Jie Zeng, Dakai Liang, Xiaoyu Ni

    It is difficult to make sure that the spliced polarization-maintaining fiber length is the same in every fabricating polarization-maintaining fiber loop mirror sensor, and it is also difficult to make sure that sensing length is the same in every experiment. To find out how these uncertain factors influence the axial strain sensitivity of polarization-maintaining fiber loop mirror, we perform the research on the influences of polarization-maintaining fiber length and sensing length on axial strain sensitivity. In this article, a theoretical model for axial strain sensitivity of polarization-maintaining fiber loop mirror is deduced first. By analyzing the theoretical model, we find that the axial strain sensitivity is unrelated to polarization-maintaining fiber length and sensing length. Then, we experimentally investigate the influences of polarization-maintaining fiber length and sensing length on axial strain sensitivity of polarization-maintaining fiber loop mirror. The axial strain sensitivities in the experiments are almost the same for different polarization-maintaining fiber lengths and different sensing lengths. The experimental results agree with the theoretical ones. The results can provide help for fabricating and applying polarization-maintaining fiber loop mirror sensor. The results can be applied in the temperature, displacement, and vibration sensors of polarization-maintaining fiber loop mirror and can also be applied in photonic crystal fiber loop mirror sensor.


    • 1 December 2013
      • Vol. 33  (12) , 3273-7

    [Study on the axial strain sensor of birefringence photonic crystal fiber loop mirror based on the absolute integral of the monitoring peak].

    by Ying Jiang, Jie Zeng, Da-Kai Liang, Xue-Liang Wang, Xiao-Yu Ni, Xiao-Yan Zhang, Ji-Feng Li, Wen-Yong Luo

    In the present paper, the theoretical expression of the wavelength change and the axial strain of birefringence fiber loop mirror is developed. The theoretical result shows that the axial strain sensitivity of birefringence photonic crystal fiber loop mirror is much lower than conventional birefringence fiber loop mirror. It is difficult to measure the axial strain by monitoring the wavelength change of birefringence photonic crystal fiber loop mirror, and it is easy to cause the measurement error because the output spectrum is not perfectly smooth. The different strain spectrum of birefringence photonic crystal fiber loop mirror was measured experimentally by an optical spectrum analyzer. The measured spectrum was analysed. The results show that the absolute integral of the monitoring peak decreases with increasing strain and the absolute integral is linear versus strain. Based on the above results, it is proposed that the axial strain can be measured by monitoring the absolute integral of the monitoring peak in this paper. The absolute integral of the monitoring peak is a comprehensive index which can indicate the light intensity of different wavelength. This method of monitoring the absolute integral of the monitoring peak to measure the axial strain can not only overcome the difficulty of monitoring the wavelength change of birefringence photonic crystal fiber loop mirror, but also reduce the measurement error caused by the unsmooth output spectrum.

    • 1 December 2012
      • Vol. 32  (12) , 3367-71

    [Research on axial strain sensitivity of high-birefringence fiber loop mirror].

    by Ying Jiang, Da-Kai Liang, Jie Zeng, Xiao-Li Zhang, Li Zhou, Xiao-Yu Ni

    In the present paper, the theoretical expressions for the axial strain sensitivity of high-birefringence fiber loop mirror (Hi-Bi FLM) was developed. The key influence factors on the axial strain sensitivity are discussed for the same input light source as the high-birefringence fiber material is certain, including the high-birefringence fiber length and the sensing length. The relationship between the high-birefringence fiber material and the axial strain sensitivity is discussed for the same input light source. The results show that the wavelength shift of high-birefringence fiber loop mirror is linear with the axial strain, and the linear sensitivity is constant decided by the high-birefringence fiber material and the center wavelength of input light source, having nothing to do with the high-birefringence fiber length and the sensing length.