Steven Letourneau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Steven Letourneau has a total of 82 co-authors. Here are the top co-authors by number of shared publications:
- Jeffrey W. Elam
Applied Materials Division Argonne National Laboratory Lemont Illinois USA
9 shared publications - Rick Ubic
Boise State University
6 shared publications - Matthias J. Young
Department of Chemistry University of Missouri Columbia Missouri USA
5 shared publications Anil U. Mane
Applied Materials Division, Argonne National Laboratory, 9700 S Cass Avenue, Lemont, Illinois60439, United States
3 shared publicationsDevika Choudhury
Applied Materials Division, Argonne National Laboratory, 9700 S Cass Avenue, Lemont, Illinois60439, United States
3 shared publications- Elton Graugnard
Boise State University
3 shared publications
Latest Publications
- Open Access
- 12 January 2023
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 35 (3) , 927-936
Thermal Atomic Layer Etching of MoS2 Using MoF6 and H2O
Two-dimensional (2D) layered materials offer unique properties that make them attractive for continued scaling in electronic and optoelectronic device applications. Successful integration of 2D materials into semiconductor manufacturing requires high-volume and high-precision processes for deposition and etching. Several promising large-scale deposition approaches have been reported for a range of 2D materials, but fewer studies have reported removal processes. Thermal atomic layer etching (ALE) is a scalable processing technique that offers precise control over isotropic material removal. In this work, we report a thermal ALE process for molybdenum disulfide (MoS2). We show that MoF6 can be used as a fluorination source, which, when combined with alternating exposures of H2O, etches both amorphous and crystalline MoS2 films deposited by atomic layer deposition. To characterize the ALE process and understand the etching reaction mechanism, in situ quartz crystal microbalance (QCM), Fourier transform infrared (FTIR), and quadrupole mass spectrometry (QMS) experiments were performed. From temperature-dependent in situ QCM experiments, the mass change per cycle was -5.7 ng/cm2 at 150 °C and reached -270.6 ng/cm2 at 300 °C, nearly 50× greater. The temperature dependence followed Arrhenius behavior with an activation energy of 13 ± 1 kcal/mol. At 200 °C, QCM revealed a mass gain following exposure to MoF6 and a net mass loss after exposure to H2O. FTIR revealed the consumption of Mo-O species and formation of Mo-F and MoF x =O species following exposures of MoF6 and the reverse behavior following H2O exposures. QMS measurements, combined with thermodynamic calculations, supported the removal of Mo and S through the formation of volatile MoF2O2 and H2S byproducts. The proposed etching mechanism involves a two-stage oxidation of Mo through the ALE half-reactions. Etch rates of 0.5 Å/cycle for amorphous films and 0.2 Å/cycle for annealed films were measured by ex situ ellipsometry, X-ray reflectivity, and transmission electron microscopy. Precisely etching amorphous films and subsequently annealing them yielded crystalline, few-layer MoS2 thin films. This thermal MoS2 ALE process provides a new mechanism for fluorination-based ALE and offers a low-temperature approach for integrating amorphous and crystalline 2D MoS2 films into high-volume device manufacturing with tight thermal budgets.
- 12 January 2023
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 35 (3) , 927-936
Open AccessThermal Atomic Layer Etching of MoS2 Using MoF6 and H2O
Two-dimensional (2D) layered materials offer unique properties that make them attractive for continued scaling in electronic and optoelectronic device applications. Successful integration of 2D materials into semiconductor manufacturing requires high-volume and high-precision processes for deposition and etching. Several promising large-scale deposition approaches have been reported for a range of 2D materials, but fewer studies have reported removal processes. Thermal atomic layer etching (ALE) is a scalable processing technique that offers precise control over isotropic material removal. In this work, we report a thermal ALE process for molybdenum disulfide (MoS2). We show that MoF6 can be used as a fluorination source, which, when combined with alternating exposures of H2O, etches both amorphous and crystalline MoS2 films deposited by atomic layer deposition. To characterize the ALE process and understand the etching reaction mechanism, in situ quartz crystal microbalance (QCM), Fourier transform infrared (FTIR), and quadrupole mass spectrometry (QMS) experiments were performed. From temperature-dependent in situ QCM experiments, the mass change per cycle was -5.7 ng/cm2 at 150 °C and reached -270.6 ng/cm2 at 300 °C, nearly 50× greater. The temperature dependence followed Arrhenius behavior with an activation energy of 13 ± 1 kcal/mol. At 200 °C, QCM revealed a mass gain following exposure to MoF6 and a net mass loss after exposure to H2O. FTIR revealed the consumption of Mo-O species and formation of Mo-F and MoF x =O species following exposures of MoF6 and the reverse behavior following H2O exposures. QMS measurements, combined with thermodynamic calculations, supported the removal of Mo and S through the formation of volatile MoF2O2 and H2S byproducts. The proposed etching mechanism involves a two-stage oxidation of Mo through the ALE half-reactions. Etch rates of 0.5 Å/cycle for amorphous films and 0.2 Å/cycle for annealed films were measured by ex situ ellipsometry, X-ray reflectivity, and transmission electron microscopy. Precisely etching amorphous films and subsequently annealing them yielded crystalline, few-layer MoS2 thin films. This thermal MoS2 ALE process provides a new mechanism for fluorination-based ALE and offers a low-temperature approach for integrating amorphous and crystalline 2D MoS2 films into high-volume device manufacturing with tight thermal budgets.
- 21 November 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 40 (6)
Nucleation and growth of molybdenum disulfide grown by thermal atomic layer deposition on metal oxides
To enable greater control over thermal atomic layer deposition (ALD) of molybdenum disulfide (MoS2), here we report studies of the reactions of molybdenum hexafluoride (MoF6) and hydrogen sulfide (H2S) with metal oxide substrates from nucleation to few-layer films. In situ quartz crystal microbalance experiments performed at 150, 200, and 250 °C revealed temperature-dependent nucleation behavior of the MoF6 precursor, which is attributed to variations in surface hydroxyl concentration with temperature. In situ Fourier transform infrared spectroscopy coupled with ex situ x-ray photoelectron spectroscopy (XPS) indicated the presence of molybdenum oxide and molybdenum oxyfluoride species during nucleation. Density functional theory calculations additionally support the formation of these species as well as predicted metal oxide to fluoride conversion. Residual gas analysis revealed reaction by-products, and the combined experimental and computational results provided insights into proposed nucleation surface reactions. With additional ALD cycles, Fourier transform infrared spectroscopy indicated steady film growth after ∼13 cycles at 200 °C. XPS revealed that higher deposition temperatures resulted in a higher fraction of MoS2 within the films. Deposition temperature was found to play an important role in film morphology with amorphous films obtained at 200 °C and below, while layered films with vertical platelets were observed at 250 °C. These results provide an improved understanding of MoS2 nucleation, which can guide surface preparation for the deposition of few-layer films and advance MoS2 toward integration into device manufacturing.
- 21 November 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 40 (6)
Nucleation and growth of molybdenum disulfide grown by thermal atomic layer deposition on metal oxides
To enable greater control over thermal atomic layer deposition (ALD) of molybdenum disulfide (MoS2), here we report studies of the reactions of molybdenum hexafluoride (MoF6) and hydrogen sulfide (H2S) with metal oxide substrates from nucleation to few-layer films. In situ quartz crystal microbalance experiments performed at 150, 200, and 250 °C revealed temperature-dependent nucleation behavior of the MoF6 precursor, which is attributed to variations in surface hydroxyl concentration with temperature. In situ Fourier transform infrared spectroscopy coupled with ex situ x-ray photoelectron spectroscopy (XPS) indicated the presence of molybdenum oxide and molybdenum oxyfluoride species during nucleation. Density functional theory calculations additionally support the formation of these species as well as predicted metal oxide to fluoride conversion. Residual gas analysis revealed reaction by-products, and the combined experimental and computational results provided insights into proposed nucleation surface reactions. With additional ALD cycles, Fourier transform infrared spectroscopy indicated steady film growth after ∼13 cycles at 200 °C. XPS revealed that higher deposition temperatures resulted in a higher fraction of MoS2 within the films. Deposition temperature was found to play an important role in film morphology with amorphous films obtained at 200 °C and below, while layered films with vertical platelets were observed at 250 °C. These results provide an improved understanding of MoS2 nucleation, which can guide surface preparation for the deposition of few-layer films and advance MoS2 toward integration into device manufacturing.
- 19 June 2020
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 38 (4)
Atomic layer deposition of HfO2 films using carbon-free tetrakis(tetrahydroborato)hafnium and water
Thin hafnium oxide films were prepared by atomic layer deposition using a carbon-free precursor, tetrakis(tetrahydroborato)hafnium [Hf(BH4)4], and H2O. Film growth was studied using an in situ quartz crystal microbalance and Fourier transform infrared spectroscopy measurements. Self-limiting growth was observed between 100 and 175 °C, but the thermal decomposition of the Hf precursor occurred at higher temperatures. The film properties were investigated using x-ray photoelectron spectroscopy, x-ray reflectivity, x-ray diffraction, ellipsometry, time-of-flight secondary ion mass spectrometry, and x-ray absorption spectroscopy. The as-deposited films were found to consist of an amorphous mixture of HfO2 and B2O3, and had a lower density and lower refractive index compared to pure HfO2 thin films. Annealing the films to >750 °C yielded crystalline monoclinic HfO2 with a density of 9 g/cm3 and a refractive index of 2.10.
- 19 June 2020
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 38 (4)
Atomic layer deposition of HfO2 films using carbon-free tetrakis(tetrahydroborato)hafnium and water
Thin hafnium oxide films were prepared by atomic layer deposition using a carbon-free precursor, tetrakis(tetrahydroborato)hafnium [Hf(BH4)4], and H2O. Film growth was studied using an in situ quartz crystal microbalance and Fourier transform infrared spectroscopy measurements. Self-limiting growth was observed between 100 and 175 °C, but the thermal decomposition of the Hf precursor occurred at higher temperatures. The film properties were investigated using x-ray photoelectron spectroscopy, x-ray reflectivity, x-ray diffraction, ellipsometry, time-of-flight secondary ion mass spectrometry, and x-ray absorption spectroscopy. The as-deposited films were found to consist of an amorphous mixture of HfO2 and B2O3, and had a lower density and lower refractive index compared to pure HfO2 thin films. Annealing the films to >750 °C yielded crystalline monoclinic HfO2 with a density of 9 g/cm3 and a refractive index of 2.10.
- 20 April 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (20) , 22804-22814
Probing the Atomic-Scale Structure of Amorphous Aluminum Oxide Grown by Atomic Layer Deposition
Atomic layer deposition (ALD) is a well-established technique for depositing nanoscale coatings with pristine control of film thickness and composition. The trimethylaluminum (TMA) and water (H2O) ALD chemistry is inarguably the most widely used, yet to date we have little information about the atomic-scale structure of the amorphous aluminum oxide (AlOx) formed by this chemistry. This lack of understanding hinders our ability to establish process-structure-property relationships and ultimately limits technological advancements employing AlOx made via ALD. In this work, we employ synchrotron High Energy X-ray Diffraction (HE-XRD) coupled with Pair Distribution Function (PDF) analysis to characterize the atomic structure of amorphous AlOx ALD coatings. We combine ex situ and in operando HE-XRD measurements on ALD AlOx, and fit this experimental data using stochastic structural modeling to reveal variations in the Al-O bond length, Al and O coordination environment, and extent of Al vacancies as a function of growth conditions. In particular, the local atomic structure of ALD AlOx is found to change with the substrate and number of ALD cycles. The observed trends are consistent with the formation of bulk Al2O3 surrounded by an O-rich surface layer. We deconvolute this data to reveal atomic-scale structural information for both the bulk and surface phases. Overall, this work demonstrates the usefulness of HE-XRD and PDF analysis in improving our understanding of the structure of amorphous ALD thin films and provides a pathway to evaluate how process changes impact the structure and properties of ALD films.
- 20 April 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (20) , 22804-22814
Probing the Atomic-Scale Structure of Amorphous Aluminum Oxide Grown by Atomic Layer Deposition
Atomic layer deposition (ALD) is a well-established technique for depositing nanoscale coatings with pristine control of film thickness and composition. The trimethylaluminum (TMA) and water (H2O) ALD chemistry is inarguably the most widely used, yet to date we have little information about the atomic-scale structure of the amorphous aluminum oxide (AlOx) formed by this chemistry. This lack of understanding hinders our ability to establish process-structure-property relationships and ultimately limits technological advancements employing AlOx made via ALD. In this work, we employ synchrotron High Energy X-ray Diffraction (HE-XRD) coupled with Pair Distribution Function (PDF) analysis to characterize the atomic structure of amorphous AlOx ALD coatings. We combine ex situ and in operando HE-XRD measurements on ALD AlOx, and fit this experimental data using stochastic structural modeling to reveal variations in the Al-O bond length, Al and O coordination environment, and extent of Al vacancies as a function of growth conditions. In particular, the local atomic structure of ALD AlOx is found to change with the substrate and number of ALD cycles. The observed trends are consistent with the formation of bulk Al2O3 surrounded by an O-rich surface layer. We deconvolute this data to reveal atomic-scale structural information for both the bulk and surface phases. Overall, this work demonstrates the usefulness of HE-XRD and PDF analysis in improving our understanding of the structure of amorphous ALD thin films and provides a pathway to evaluate how process changes impact the structure and properties of ALD films.
- 4 February 2020
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 32 (5) , 1794-1806
Descriptor-Based Analysis of Atomic Layer Deposition Mechanisms on Spinel LiMn2O4 Lithium-Ion Battery Cathodes
- 4 February 2020
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 32 (5) , 1794-1806
Descriptor-Based Analysis of Atomic Layer Deposition Mechanisms on Spinel LiMn2O4 Lithium-Ion Battery Cathodes
- 15 January 2020
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 32 (3) , 992-1001
Molecular Layer Etching of Metalcone Films Using Lithium Organic Salts and Trimethylaluminum
- 15 January 2020
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 32 (3) , 992-1001
Molecular Layer Etching of Metalcone Films Using Lithium Organic Salts and Trimethylaluminum
- Open Access
- 6 September 2019
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 123 (39) , 23783-23790
High-Rate Spinel LiMn2O4 (LMO) Following Carbonate Removal and Formation of Li-Rich Interface by ALD Treatment
- 6 September 2019
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 123 (39) , 23783-23790
Open AccessHigh-Rate Spinel LiMn2O4 (LMO) Following Carbonate Removal and Formation of Li-Rich Interface by ALD Treatment
- 1 March 2019
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 9 (4) , 3198-3207
Introducing Nonstructural Ligands to Zirconia-like Metal–Organic Framework Nodes To Tune the Activity of Node-Supported Nickel Catalysts for Ethylene Hydrogenation
- 1 March 2019
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 9 (4) , 3198-3207
Introducing Nonstructural Ligands to Zirconia-like Metal–Organic Framework Nodes To Tune the Activity of Node-Supported Nickel Catalysts for Ethylene Hydrogenation
- 24 July 2018
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 1 (8) , 4028-4037
Structural Evolution of Molybdenum Disulfide Prepared by Atomic Layer Deposition for Realization of Large Scale Films in Microelectronic Applications
- 24 July 2018
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 1 (8) , 4028-4037
Structural Evolution of Molybdenum Disulfide Prepared by Atomic Layer Deposition for Realization of Large Scale Films in Microelectronic Applications