Thermal Atomic Layer Etching of MoS2 Using MoF6 and H2O
Open Access
- 12 January 2023
- journal article
- research article
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 35 (3) , 927-936
Abstract
Two-dimensional (2D) layered materials offer unique properties that make them attractive for continued scaling in electronic and optoelectronic device applications. Successful integration of 2D materials into semiconductor manufacturing requires high-volume and high-precision processes for deposition and etching. Several promising large-scale deposition approaches have been reported for a range of 2D materials, but fewer studies have reported removal processes. Thermal atomic layer etching (ALE) is a scalable processing technique that offers precise control over isotropic material removal. In this work, we report a thermal ALE process for molybdenum disulfide (MoS2). We show that MoF6 can be used as a fluorination source, which, when combined with alternating exposures of H2O, etches both amorphous and crystalline MoS2 films deposited by atomic layer deposition. To characterize the ALE process and understand the etching reaction mechanism, in situ quartz crystal microbalance (QCM), Fourier transform infrared (FTIR), and quadrupole mass spectrometry (QMS) experiments were performed. From temperature-dependent in situ QCM experiments, the mass change per cycle was -5.7 ng/cm2 at 150 °C and reached -270.6 ng/cm2 at 300 °C, nearly 50× greater. The temperature dependence followed Arrhenius behavior with an activation energy of 13 ± 1 kcal/mol. At 200 °C, QCM revealed a mass gain following exposure to MoF6 and a net mass loss after exposure to H2O. FTIR revealed the consumption of Mo-O species and formation of Mo-F and MoF x =O species following exposures of MoF6 and the reverse behavior following H2O exposures. QMS measurements, combined with thermodynamic calculations, supported the removal of Mo and S through the formation of volatile MoF2O2 and H2S byproducts. The proposed etching mechanism involves a two-stage oxidation of Mo through the ALE half-reactions. Etch rates of 0.5 Å/cycle for amorphous films and 0.2 Å/cycle for annealed films were measured by ex situ ellipsometry, X-ray reflectivity, and transmission electron microscopy. Precisely etching amorphous films and subsequently annealing them yielded crystalline, few-layer MoS2 thin films. This thermal MoS2 ALE process provides a new mechanism for fluorination-based ALE and offers a low-temperature approach for integrating amorphous and crystalline 2D MoS2 films into high-volume device manufacturing with tight thermal budgets.Keywords
Funding Information
- Basic Energy Sciences
- Division of Civil, Mechanical and Manufacturing Innovation (1751268)
This publication has 52 references indexed in Scilit:
- Layer Thinning and Etching of Mechanically Exfoliated MoS2 Nanosheets by Thermal Annealing in AirSmall, 2013
- Atomic Layer Deposition of Ga2O3 Films Using Trimethylgallium and OzoneChemistry of Materials, 2012
- Electronic structure of a single MoS2 monolayerSolid State Communications, 2012
- From Bulk to Monolayer MoS2: Evolution of Raman ScatteringAdvanced Functional Materials, 2012
- Photoluminescence from Chemically Exfoliated MoS2Nano Letters, 2011
- Enhanced etching of sapphire damaged by ion implantationJournal of Physics D: Applied Physics, 1998
- HSC Chemistry for Windows, 2.0Journal of Chemical Information and Computer Sciences, 1996
- Amorphous MoS2 as the cathode of lithium secondary batteriesJournal of Power Sources, 1995
- Texture characterisation of sputtered MoS2thin films by cross-sectional TEM analysisJournal of Physics D: Applied Physics, 1990
- In-situ observation of Mo-O stretching vibrations during the reduction of MoO3 with hydrogen by diffuse reflectance FTIR spectroscopyApplied Surface Science, 1989