SSShelas Sathyan

Shelas Sathyan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Shelas Sathyan has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Reconfigurable DAB Converter With Variable Transformer Turns for Wide Voltage Range Using Hybrid EPS Modulation

    by Harikesh V. Kurup, Shelas Sathyan, Praveen Kumar K. S.

    In this article, a variable transformer-based modified dual-active bridge (DAB) converter is proposed that has wide voltage range performance. The conventional DAB delivers maximum efficiency and performance only at unity voltage ratio and also fails to deliver wide voltage range operation. To overcome these limitations, this work proposes a modified DAB with reconfigurable secondary that can handle a wide output voltage range using transformer turns ratio. The variable secondary of the transformer provides three turns-ratio choices, and the reconfigurable bridge provides three operating modes for each. In effect, the converter operates in nine different modes, delivering higher performance over a voltage gain range of 0.3 to 4. In order to minimize the current stress across the switches and reduce losses, a hybrid extended phase shift modulation is proposed, which enhances the overall performance of the converter. A 500 W prototype is built for the proposed converter configuration, and the effectiveness is experimentally verified.

  • A New Control Scheme for V2G Power Transfer in Modified Series-Parallel Resonant Converter

    by N. J. Merlin Mary, Shelas Sathyan

    The dual active bridge (DAB) modified series-parallel resonant converter (MSPRC) is best suited for grid-to-vehicle (G2V) power transfer due to the narrow frequency range of operation, good short-circuit protection performance, and minimized circulating losses. For vehicle-to-grid (V2G) power transfer of MSPRC, efficiency is poor when the battery discharges to its lowest voltage. This paper proposes a new control scheme for V2G power transfer in MSPRC. The proposed constant power discharge frequency modulation scheme gives high conversion efficiency for V2G operation. The input voltage is maintained constant during the discharging operation for the wide variations in battery voltage. All the switches in the primary and secondary bridge of the proposed converter achieve soft switching. A three-level structure on the primary bridge allows the usage of low on-state resistance switches, thereby minimizing the switch conduction losses. The converter and its proposed control scheme are applicable for three-phase on-board battery chargers where the DC link voltage is very high. The experimental results from a 3.3-kW prototype validate the performance of the proposed control scheme.

  • A modified CLC‐T resonant converter with inherent constant current ‐ constant voltage battery charging

    by Merlin Mary Narla John, Shelas Satyan

    Frequency‐modulated (FM) resonant converters are widely used in onboard battery chargers for constant current (CC) ‐ constant voltage (CV) charging of lithium‐ion batteries in electric vehicles. One of the significant challenges of FM converters is that they require precise control of current followed by voltage to avoid risks due to overcurrents and overvoltages. Also, there is an increased backflow current, peak current stress, magnetic losses, and switching losses when the frequency of operation is away from the resonant frequency. To overcome these issues, this paper proposes a modified CLC‐T resonant converter that operates only at resonant switching frequency but has an inherent smooth transition from CC to CV for battery charging. During CC charging, the resonant tank is CLC‐T, and the secondary circuit is a full‐bridge rectifier. As the battery voltage increases and reaches the rated value, the secondary diodes enter into cut‐off mode, modifying the secondary circuit into a half‐bridge rectifier. Thus, the resonant tank is automatically converted to CL, and there is a shift into CV charging. During the entire charging operation, the switches and diodes are soft‐switched. The switches attain either near‐zero phase angle or zero‐voltage switching operation, whereas the diodes attain zero‐current switchings. A hardware prototype of 400 V input and 320–420 V output battery charger was developed, tested, and validated in the laboratory. The highest efficiency of the overall charging system is 97.4%.


  • Design and Analysis of Modified Series–Parallel Quasiresonant Half-Bridge DC/DC Converter for Renewable Energy Applications

    by Sugali Harinaik, Shelas Sathyan, N. J. Merlin Mary

    This article presents a half-bridge current-fed modified series-parallel quasi-resonant (MSPQR) DC/DC converter for renewable energy sources (RESs). A modified series-parallel resonant tank (MSPRT) obtains partial resonance at on period ( $T_{ON}$ ) of the semiconductor switches. As a result of the partial resonance, the switches experience natural commutation before the withdrawal of the gate signal. Thus the semiconductor switches achieve zero current switching (ZCS) at a turn-off instant, which reduces the switching losses. Hence, the highfrequency operation is feasible, which improves the converter's efficiency and power density. In addition, high frequency transformer (HFT), two boost inductors, and voltage doubler are used for higher voltage gain. In this converter, less frequency variation is required to regulate the constant output voltage over a wide range of load and input source variation. The voltage stress across each MOSFET is lower compared to output voltage. Thus the need for a snubber circuit is eliminated, and switches of low $R_{DS(on)}$ can be chosen for this converter. Due to common ground sharing, a high-side gate driver circuit is not required. In this converter, ZCS is obtained for varying input voltage and wide load ranges with less variation in the operating frequency. The performance of frequency-modulated converter is verified through laboratory testing of a 500W hardware prototype. The steady-state waveforms and experimental results confirm the converter's proof of concept.


  • A Novel Bidirectional CLC-T Resonant Immittance Converter for CC / CV Battery Charging

    by N. J. Merlin Mary, Shelas Sathyan

    This paper proposes a novel bidirectional CLC-T resonant immittance converter with a modified secondary for electric vehicle battery charging applications. The proposed converter has inherent constant current (CC) / constant voltage (CV) charging characteristics and is operated only at the resonant frequency. The first harmonic approximation (FHA) technique is used to design the proposed 3.3 kW, 400 V input, 320–420 V output resonant immittance converter. The converter performance at steady-state in charging and discharging operation modes is validated using PSIM simulation. In charging mode, the converter delivers constant current output till the battery reaches the rated voltage. Beyond that, it delivers constant voltage output with decreasing current. The resonant tank is equivalent to CLC-T and CL in CC and CV modes. All the switches attain zero voltage switching in charging and discharging operations. The circulating losses are drastically reduced, which increases the efficiency of the proposed converter as it is operated only at the fixed resonant frequency. As no modulation technique is involved, the complexity of the controller implementation for CC / CV charging is eliminated.


  • Design and analysis of isolated high step-up Y-source DC/DC resonant converter for photovoltaic applications

    by Harinaik Sugali, Shelas Sathyan

    This paper presents the design and analysis of an isolated high step-up Y-source DC/DC converter for photovoltaic systems. At high switching frequencies, the conventional impedance source converter (ISC) experiences higher switching losses. To mitigate this, a high gain soft-switched frequency-modulated Y-source DC/DC converter is proposed. Here, soft switching is implemented on the Y-source impedance converter by creating quasi-resonance during a shoot-through instant. Thus, quasi-resonance occurs by an LC resonant tank, and it is formed using a resonant capacitor and leakage inductance of a transformer. It ensures that all the active switches are turned off with zero current switching (ZCS) and the voltage stress on each switch is much lower than the output voltage with lower turn-off voltage spikes. Thus, it eliminates the need for a snubber circuit. The output voltage is regulated by frequency modulation with the ON period of all four active switches kept constant. The converter can also deliver a continuous input current (CIC) and high voltage gain with a small shoot-through duty ratio (dST). The galvanic isolation of the converter helps to eliminate the leakage current issues and safety hazards faced by the non-isolated counterparts. The proposed topology has all the inherent characteristics of a typical impedance source DC/DC converter with higher conversion efficiency over a wide range of output loads. The proposed converter achieves 96.46% of full load efficiency. Finally, a 200W prototype is built and tested in the laboratory to verify the converter design and performance.


  • A Three-Level Resonant DAB Converter Featuring Minimized Circulating Losses for EV Battery Charging

    by N. J. Merlin Mary, Shelas Sathyan, Hiralal Muralidhar Suryawanshi

    A three-level modified series–parallel bidirectional isolated dc–dc resonant converter (TL-MSPBRC) is proposed for electric vehicle (EV) battery charging. The converter's performance is enhanced for wide load conditions as the modified series–parallel resonant tank is formed by considering the parasitics in the transformer. The first-harmonic approximation (FHA) equivalent circuit model is employed to analyze the converter characteristics for the frequency modulation technique. This converter has high conversion efficiency in charging and discharging operations because of the soft-switching capability of the power switches in the primary and secondary bridges. In addition, low on -state resistance switches in the three-level primary bridge minimize the conduction losses. A 3.3-kW converter prototype with a battery voltage range of 230 $-$ 300-V is developed to validate the design method and the simulation results. The proposed converter has minimized circulating losses, good short-circuit protection, and excellent efficiency of 97.7% at the rated power level.