Harinaik Sugali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Harinaik Sugali has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Shelas Sathyan
National Institute of Technology
3 shared publications - Merlin Mary Narla John
National Institute of Technology Tiruchirappalli,Department of Electrical and Electronics Engineering,Trichy,India
1 shared publication N. J. Merlin Mary
Department of Electrical and Electronics Engineering, National Institute of Technology, Tiruchirappalli, India
1 shared publicationShelas Sathyan
Department of Electrical and Electronics Engineering, National Institute of Technology, Tiruchirappalli, India
1 shared publication
Latest Publications
- 25 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 5 (3) , 1089-1099
Design and Analysis of Modified Series–Parallel Quasiresonant Half-Bridge DC/DC Converter for Renewable Energy Applications
This article presents a half-bridge current-fed modified series-parallel quasi-resonant (MSPQR) DC/DC converter for renewable energy sources (RESs). A modified series-parallel resonant tank (MSPRT) obtains partial resonance at on period ( $T_{ON}$ ) of the semiconductor switches. As a result of the partial resonance, the switches experience natural commutation before the withdrawal of the gate signal. Thus the semiconductor switches achieve zero current switching (ZCS) at a turn-off instant, which reduces the switching losses. Hence, the highfrequency operation is feasible, which improves the converter's efficiency and power density. In addition, high frequency transformer (HFT), two boost inductors, and voltage doubler are used for higher voltage gain. In this converter, less frequency variation is required to regulate the constant output voltage over a wide range of load and input source variation. The voltage stress across each MOSFET is lower compared to output voltage. Thus the need for a snubber circuit is eliminated, and switches of low $R_{DS(on)}$ can be chosen for this converter. Due to common ground sharing, a high-side gate driver circuit is not required. In this converter, ZCS is obtained for varying input voltage and wide load ranges with less variation in the operating frequency. The performance of frequency-modulated converter is verified through laboratory testing of a 500W hardware prototype. The steady-state waveforms and experimental results confirm the converter's proof of concept.
- 25 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 5 (3) , 1089-1099
Design and Analysis of Modified Series–Parallel Quasiresonant Half-Bridge DC/DC Converter for Renewable Energy Applications
This article presents a half-bridge current-fed modified series-parallel quasi-resonant (MSPQR) DC/DC converter for renewable energy sources (RESs). A modified series-parallel resonant tank (MSPRT) obtains partial resonance at on period ( $T_{ON}$ ) of the semiconductor switches. As a result of the partial resonance, the switches experience natural commutation before the withdrawal of the gate signal. Thus the semiconductor switches achieve zero current switching (ZCS) at a turn-off instant, which reduces the switching losses. Hence, the highfrequency operation is feasible, which improves the converter's efficiency and power density. In addition, high frequency transformer (HFT), two boost inductors, and voltage doubler are used for higher voltage gain. In this converter, less frequency variation is required to regulate the constant output voltage over a wide range of load and input source variation. The voltage stress across each MOSFET is lower compared to output voltage. Thus the need for a snubber circuit is eliminated, and switches of low $R_{DS(on)}$ can be chosen for this converter. Due to common ground sharing, a high-side gate driver circuit is not required. In this converter, ZCS is obtained for varying input voltage and wide load ranges with less variation in the operating frequency. The performance of frequency-modulated converter is verified through laboratory testing of a 500W hardware prototype. The steady-state waveforms and experimental results confirm the converter's proof of concept.
- 4 September 2023
- Published by Taylor & Francis in International Journal of Electronics
- Vol. 111 (12) , 2159-2179
Design and analysis of quasi-resonant high-gain impedance source DC–DC converter for DC microgrid
- 4 September 2023
- Published by Taylor & Francis in International Journal of Electronics
- Vol. 111 (12) , 2159-2179
Design and analysis of quasi-resonant high-gain impedance source DC–DC converter for DC microgrid
- 21 February 2023
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 45 (1) , 1604-1623
Design and analysis of isolated high step-up Y-source DC/DC resonant converter for photovoltaic applications
This paper presents the design and analysis of an isolated high step-up Y-source DC/DC converter for photovoltaic systems. At high switching frequencies, the conventional impedance source converter (ISC) experiences higher switching losses. To mitigate this, a high gain soft-switched frequency-modulated Y-source DC/DC converter is proposed. Here, soft switching is implemented on the Y-source impedance converter by creating quasi-resonance during a shoot-through instant. Thus, quasi-resonance occurs by an LC resonant tank, and it is formed using a resonant capacitor and leakage inductance of a transformer. It ensures that all the active switches are turned off with zero current switching (ZCS) and the voltage stress on each switch is much lower than the output voltage with lower turn-off voltage spikes. Thus, it eliminates the need for a snubber circuit. The output voltage is regulated by frequency modulation with the ON period of all four active switches kept constant. The converter can also deliver a continuous input current (CIC) and high voltage gain with a small shoot-through duty ratio . The galvanic isolation of the converter helps to eliminate the leakage current issues and safety hazards faced by the non-isolated counterparts. The proposed topology has all the inherent characteristics of a typical impedance source DC/DC converter with higher conversion efficiency over a wide range of output loads. The proposed converter achieves 96.46% of full load efficiency. Finally, a 200W prototype is built and tested in the laboratory to verify the converter design and performance.- 21 February 2023
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 45 (1) , 1604-1623
Design and analysis of isolated high step-up Y-source DC/DC resonant converter for photovoltaic applications
This paper presents the design and analysis of an isolated high step-up Y-source DC/DC converter for photovoltaic systems. At high switching frequencies, the conventional impedance source converter (ISC) experiences higher switching losses. To mitigate this, a high gain soft-switched frequency-modulated Y-source DC/DC converter is proposed. Here, soft switching is implemented on the Y-source impedance converter by creating quasi-resonance during a shoot-through instant. Thus, quasi-resonance occurs by an LC resonant tank, and it is formed using a resonant capacitor and leakage inductance of a transformer. It ensures that all the active switches are turned off with zero current switching (ZCS) and the voltage stress on each switch is much lower than the output voltage with lower turn-off voltage spikes. Thus, it eliminates the need for a snubber circuit. The output voltage is regulated by frequency modulation with the ON period of all four active switches kept constant. The converter can also deliver a continuous input current (CIC) and high voltage gain with a small shoot-through duty ratio . The galvanic isolation of the converter helps to eliminate the leakage current issues and safety hazards faced by the non-isolated counterparts. The proposed topology has all the inherent characteristics of a typical impedance source DC/DC converter with higher conversion efficiency over a wide range of output loads. The proposed converter achieves 96.46% of full load efficiency. Finally, a 200W prototype is built and tested in the laboratory to verify the converter design and performance.- Open Access
- 3 January 2023
- Published by River Publishers in Distributed Generation & Alternative Energy Journal
- p. 569–594
Design and Analysis of Quasi-Y Source High Gain DC/DC Resonant Converter for Renewable Energy Applications
This paper proposes a magnetically coupled partial resonant isolated quasi-Y source DC/DC converter. Here, to achieve soft switching, there is no additional auxiliary circuits or magnetic components are used. By making use of transformer’s parasitic elements like winding capacitance (Cp) and leakage inductance (Lk1), zero current switching (ZCS) is obtained at the turn-off instant of all MOSFETs. Hence, the converter can operate at a higher frequency, so that compact size and good efficiency are feasible. This converter inherits all the conventional impedance source converter features, and a higher gain is obtained by using three winding coupled inductor and isolation transformer with small shoot-through duty (dST). Hence, the continuous input current (CIC) and galvanic isolation feature of this converter is most suitable for renewable energy applications. Also, the output voltage is regulated by changing the switching frequency. Finally, a 300 W prototype is designed and tested in the laboratory. The simulation, experimental results with mathematical and design analysis are provided.
- 3 January 2023
- Published by River Publishers in Distributed Generation & Alternative Energy Journal
- p. 569–594
Open AccessDesign and Analysis of Quasi-Y Source High Gain DC/DC Resonant Converter for Renewable Energy Applications
This paper proposes a magnetically coupled partial resonant isolated quasi-Y source DC/DC converter. Here, to achieve soft switching, there is no additional auxiliary circuits or magnetic components are used. By making use of transformer’s parasitic elements like winding capacitance (Cp) and leakage inductance (Lk1), zero current switching (ZCS) is obtained at the turn-off instant of all MOSFETs. Hence, the converter can operate at a higher frequency, so that compact size and good efficiency are feasible. This converter inherits all the conventional impedance source converter features, and a higher gain is obtained by using three winding coupled inductor and isolation transformer with small shoot-through duty (dST). Hence, the continuous input current (CIC) and galvanic isolation feature of this converter is most suitable for renewable energy applications. Also, the output voltage is regulated by changing the switching frequency. Finally, a 300 W prototype is designed and tested in the laboratory. The simulation, experimental results with mathematical and design analysis are provided.