Tomáš Kekule
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tomáš Kekule has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Bohumil Smola
Charles University in Prague
10 shared publications - Martin Vlach
Charles University
10 shared publications - Hana Kudrnova
Charles University in Prague
9 shared publications - Ivana Stulíková
Charles University in Prague
9 shared publications - Jakub Čížek
Faculty of Mathematics and Physics, Charles University, Prague, Czech Republic
4 shared publications - Jaroslav Málek
Faculty of Mechanical Engineering, Czech Technical University in Prague, 121 35 Prague, Czech Republic
4 shared publications
Latest Publications
- 1 December 2022
- Published by American Association of Physics Teachers (AAPT) in The Physics Teacher
- Vol. 60 (9) , 759-761
Poggendorff’s Scales—Demonstration of Newton’s Laws in a Less Traditional Way
Newton’s laws are essential for understanding causes and description of mechanical motion. Great attention is paid to them during physics education. Unfortunately, many students, not only in high school, but also undergraduates, can recite them but do not understand their essence. Therefore, it is useful to demonstrate different experiments in the classroom in order to support and strengthen their understanding. Less traditional experiments demonstrating Newton’s laws can be performed using Poggendorff’s scales (also known as Poggendorff’s fall device). This article presents four experiments with such a device that are not common and lead to a deeper understanding of Newton’s laws.
- 1 December 2022
- Published by American Association of Physics Teachers (AAPT) in The Physics Teacher
- Vol. 60 (9) , 759-761
Poggendorff’s Scales—Demonstration of Newton’s Laws in a Less Traditional Way
Newton’s laws are essential for understanding causes and description of mechanical motion. Great attention is paid to them during physics education. Unfortunately, many students, not only in high school, but also undergraduates, can recite them but do not understand their essence. Therefore, it is useful to demonstrate different experiments in the classroom in order to support and strengthen their understanding. Less traditional experiments demonstrating Newton’s laws can be performed using Poggendorff’s scales (also known as Poggendorff’s fall device). This article presents four experiments with such a device that are not common and lead to a deeper understanding of Newton’s laws.
- 31 October 2022
- Published by IOP Publishing in Physics Education
- Vol. 58 (1) , 015009
Simple demonstration of Ampere’s law
Demonstrating some physical principles of university physics is not always easy. The idea of a simple demonstration of Ampere’s law is presented. The induction of the magnetic field around the closed path is ‘made visible’ by measuring the voltage induced in the winding surrounding the path.
- 31 October 2022
- Published by IOP Publishing in Physics Education
- Vol. 58 (1) , 015009
Simple demonstration of Ampere’s law
Demonstrating some physical principles of university physics is not always easy. The idea of a simple demonstration of Ampere’s law is presented. The induction of the magnetic field around the closed path is ‘made visible’ by measuring the voltage induced in the winding surrounding the path.
- 1 January 2021
- Published by Central Library of the Slovak Academy of Sciences in Metallic Materials
- Vol. 52 (05) , 295-304
Annealing effects in hot-deformed Al-Mn-Sc-Zr alloys
Annealing effects in hot-deformed Al-Mn-Sc-Zr alloys
- 1 January 2021
- Published by Central Library of the Slovak Academy of Sciences in Metallic Materials
- Vol. 52 (05) , 295-304
Annealing effects in hot-deformed Al-Mn-Sc-Zr alloys
Annealing effects in hot-deformed Al-Mn-Sc-Zr alloys
- Open Access
Role of Small Addition of Sc and Zr in Clustering and Precipitation Phenomena Induced in AA7075
A detailed characterization of phase transformations in the heat-treated commercial 7075 aluminum alloys without/with low Sc–Zr addition was carried out. Mechanical and electrical properties, thermal and corrosion behavior were compared to the microstructure development. The eutectic phase consists of four parts: MgZn2 phase, Al2CuMg phase (S-phase), Al2Zn3Mg3 phase (T-phase), and primary λ-Al(Mn,Fe,Si) phase. Strengthening during non-isothermal (isochronal) annealing is caused by a combination of formation of the GP zones, η’-phase, T-phase and co-presence of the primary and secondary Al3(Sc,Zr)-phase particles. Positive influence on corrosion properties is owing to the addition of Sc–Zr. Positron annihilation showed an evolution of solute Zn,Mg-(co-)clusters into (precursors of) the GP zones in the course of natural ageing. The concentration of the (co-)clusters is slightly negatively affected by the low Sc–Zr addition. A combination of both precipitation sequences of the Al–Zn–Mg–Cu-based system was observed. The apparent activation energy values for dissolution/formation of the clusters/GP zones and for formation of the metastable η’-phase, stable T-phase and stable η-phase were calculated.
Open AccessRole of Small Addition of Sc and Zr in Clustering and Precipitation Phenomena Induced in AA7075
A detailed characterization of phase transformations in the heat-treated commercial 7075 aluminum alloys without/with low Sc–Zr addition was carried out. Mechanical and electrical properties, thermal and corrosion behavior were compared to the microstructure development. The eutectic phase consists of four parts: MgZn2 phase, Al2CuMg phase (S-phase), Al2Zn3Mg3 phase (T-phase), and primary λ-Al(Mn,Fe,Si) phase. Strengthening during non-isothermal (isochronal) annealing is caused by a combination of formation of the GP zones, η’-phase, T-phase and co-presence of the primary and secondary Al3(Sc,Zr)-phase particles. Positive influence on corrosion properties is owing to the addition of Sc–Zr. Positron annihilation showed an evolution of solute Zn,Mg-(co-)clusters into (precursors of) the GP zones in the course of natural ageing. The concentration of the (co-)clusters is slightly negatively affected by the low Sc–Zr addition. A combination of both precipitation sequences of the Al–Zn–Mg–Cu-based system was observed. The apparent activation energy values for dissolution/formation of the clusters/GP zones and for formation of the metastable η’-phase, stable T-phase and stable η-phase were calculated.
- 1 March 2018
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 738, 173-181
Natural and artificial aging in Mg-Gd binary alloys
- 1 March 2018
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 738, 173-181
Natural and artificial aging in Mg-Gd binary alloys
- Open Access
- 1 January 2018
- Published by Central Library of the Slovak Academy of Sciences in Metallic Materials
- Vol. 56 (06) , 367-377
Characterization of phase development in commercial Al-Zn-Mg(-Mn,Fe) alloy with and without Sc,Zr-addition
Characterization of phase development in commercial Al-Zn-Mg(-Mn,Fe) alloy with and without Sc,Zr-addition
- 1 January 2018
- Published by Central Library of the Slovak Academy of Sciences in Metallic Materials
- Vol. 56 (06) , 367-377
Open AccessCharacterization of phase development in commercial Al-Zn-Mg(-Mn,Fe) alloy with and without Sc,Zr-addition
Characterization of phase development in commercial Al-Zn-Mg(-Mn,Fe) alloy with and without Sc,Zr-addition
- Open Access
- 1 June 2017
- Published by Elsevier in Journal of Magnesium and Alloys
- Vol. 5 (2) , 173-180
Thermal stability and microstructure development of cast and powder metallurgy produced Mg–Y–Zn alloy during heat treatment
- 1 June 2017
- Published by Elsevier in Journal of Magnesium and Alloys
- Vol. 5 (2) , 173-180
Open AccessThermal stability and microstructure development of cast and powder metallurgy produced Mg–Y–Zn alloy during heat treatment
- 1 July 2016
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 369, 157-162
Development of Microstructure and Properties of Mg-Y-(Nd)-Zn Alloys during Heat and Mechanical Treatment
This work is focused on development of microstructure and properties of Mg-Y-Zn and Mg-Y-Nd-Zn alloys during heat and mechanical treatment. In the as-cast state both alloys exhibit almost equiaxed grains with little larger size in Mg-Y-Zn alloy and grain boundaries decorated by different structures - long period ordered structure (LPSO) was detected in Mg-Y-Zn alloy and eutectics of Mg3Nd type structure in alloy with Nd addition. A high density of stacking faults is evident in both alloys. Both alloys were repeatedly isochronally heat treated from room temperature up to 440 °C. Resistivity and microhardness measurement was performed after each heating step. Stacking faults persist both annealings in both alloys and microhardness development shows no remarkable differences. LPSO in Mg-Y-Zn alloy disappears after the first annealing and was again detected after repeated annealing up to 340 °C. After the whole treatment no grain growth appeared. Differential scanning calorimetry measurement was performed at both repeatedly heated alloys up to 540 °C. There are three exothermic peaks in DSC curves of Mg-Y-Zn alloys that can be ascribed to embedding solute atoms in stacking faults, LPSO development and transformation and coarsening of grain boundary particles. DSC curves of Mg-Y-Nd-Zn alloy exhibit two exothermic peaks that probably correspond to precipitation of basal plates of γ ́and γ phase. Measurement of microhardness was performed after sequential deformation of both alloys in the as-cast state. The alloys were cold rolled in steps of 0,9 % thickness reduction up to cracks formation. Strengthening of both alloys is very similar but formation of cracks in the alloy with Nd addition begins after a lower reduction (about 11 %) compared to Mg-Y-Zn alloy (about 15 %).
- 1 July 2016
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 369, 157-162
Development of Microstructure and Properties of Mg-Y-(Nd)-Zn Alloys during Heat and Mechanical Treatment
This work is focused on development of microstructure and properties of Mg-Y-Zn and Mg-Y-Nd-Zn alloys during heat and mechanical treatment. In the as-cast state both alloys exhibit almost equiaxed grains with little larger size in Mg-Y-Zn alloy and grain boundaries decorated by different structures - long period ordered structure (LPSO) was detected in Mg-Y-Zn alloy and eutectics of Mg3Nd type structure in alloy with Nd addition. A high density of stacking faults is evident in both alloys. Both alloys were repeatedly isochronally heat treated from room temperature up to 440 °C. Resistivity and microhardness measurement was performed after each heating step. Stacking faults persist both annealings in both alloys and microhardness development shows no remarkable differences. LPSO in Mg-Y-Zn alloy disappears after the first annealing and was again detected after repeated annealing up to 340 °C. After the whole treatment no grain growth appeared. Differential scanning calorimetry measurement was performed at both repeatedly heated alloys up to 540 °C. There are three exothermic peaks in DSC curves of Mg-Y-Zn alloys that can be ascribed to embedding solute atoms in stacking faults, LPSO development and transformation and coarsening of grain boundary particles. DSC curves of Mg-Y-Nd-Zn alloy exhibit two exothermic peaks that probably correspond to precipitation of basal plates of γ ́and γ phase. Measurement of microhardness was performed after sequential deformation of both alloys in the as-cast state. The alloys were cold rolled in steps of 0,9 % thickness reduction up to cracks formation. Strengthening of both alloys is very similar but formation of cracks in the alloy with Nd addition begins after a lower reduction (about 11 %) compared to Mg-Y-Zn alloy (about 15 %).
- 1 July 2015
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 365, 42-48
Influence of Natural Ageing on Precipitation Processes during Isochronal Annealing in MgGd Alloys
The Mg-10 wt. % Gd and Mg-15 wt. % Gd alloys produced by squeeze casting were solution treated at 500 °C for 8 hours and subsequently naturally aged for more than 2 months. Electrical resistivity of both materials measured at 77 K decreases, if the alloys are kept at room temperature after quenching from the solution temperature. This change accompanied by a microhardness increase almost saturates after 2 months and is caused most probably by solute atoms clustering. Phase transformations and microhardness changes were investigated during isochronal annealing in both naturally aged alloys in comparison to just solution treated ones. Electrical resistivity changes measured at 77 K were used to characterize microstructure development. Transmission electron microscopy was performed at selected states heat treated in the identical way. The Mg15Gd supersaturated solid solution isochronally annealed up to 500 °C immediately after the solution treatment decomposes into following successive phases: β ́ ́ (D019) metastable → β ́ (cbco) metastable → β (Mg5Gd) stable. All three possible orientation relationship modes of the metastable β ́ (cbco) phase existed at lower temperatures (up to 280 °C) but only one mode persists up to 330 °C. Precipitation of the β ́ (cbco) phase has not been observed in the Mg10Gd alloy annealed isochronally immediately after the solution treatment. The natural ageing does not change the precipitation sequence but concentration of Gd atoms involved in individual precipitation processes is influenced in both alloys. Peak hardening increases after natural ageing in the Mg15Gd alloy, shifts to higher temperatures and the temperature region of peak hardening extends.
- 1 July 2015
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 365, 42-48
Influence of Natural Ageing on Precipitation Processes during Isochronal Annealing in MgGd Alloys
The Mg-10 wt. % Gd and Mg-15 wt. % Gd alloys produced by squeeze casting were solution treated at 500 °C for 8 hours and subsequently naturally aged for more than 2 months. Electrical resistivity of both materials measured at 77 K decreases, if the alloys are kept at room temperature after quenching from the solution temperature. This change accompanied by a microhardness increase almost saturates after 2 months and is caused most probably by solute atoms clustering. Phase transformations and microhardness changes were investigated during isochronal annealing in both naturally aged alloys in comparison to just solution treated ones. Electrical resistivity changes measured at 77 K were used to characterize microstructure development. Transmission electron microscopy was performed at selected states heat treated in the identical way. The Mg15Gd supersaturated solid solution isochronally annealed up to 500 °C immediately after the solution treatment decomposes into following successive phases: β ́ ́ (D019) metastable → β ́ (cbco) metastable → β (Mg5Gd) stable. All three possible orientation relationship modes of the metastable β ́ (cbco) phase existed at lower temperatures (up to 280 °C) but only one mode persists up to 330 °C. Precipitation of the β ́ (cbco) phase has not been observed in the Mg10Gd alloy annealed isochronally immediately after the solution treatment. The natural ageing does not change the precipitation sequence but concentration of Gd atoms involved in individual precipitation processes is influenced in both alloys. Peak hardening increases after natural ageing in the Mg15Gd alloy, shifts to higher temperatures and the temperature region of peak hardening extends.
- 29 January 2015
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 46 (4) , 1556-1564
Early Stages of Precipitation Process in Al-(Mn-)Sc-Zr Alloy Characterized by Positron Annihilation
- 29 January 2015
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 46 (4) , 1556-1564
Early Stages of Precipitation Process in Al-(Mn-)Sc-Zr Alloy Characterized by Positron Annihilation