LBLeonardo Bergami

Leonardo Bergami

*This is an algorithmically generated author record based on publicly available information.

Leonardo Bergami has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High fidelity aeroelastic stability analysis of operating wind turbines

    by Armin Hermes, Frederik Zahle, Riccardo Riva, Jesper Madsen, Leonardo Bergami, Casper Skovby


  • Open Access

    The Importance of Wake Meandering on Wind Turbine Fatigue Loads in Wake

    by Jennifer Marie Rinker, Esperanza Soto Sagredo, Leonardo Bergami

    Considering loads when optimizing wind-farm layouts or designing farm-control strategies is important, but the computational cost of using high-fidelity wake models in the loop can be prohibitively high. Using simpler models that consider only the spatial variation of turbulence statistics is a tempting alternative, but the accuracy of these models with respect to the aeroelastic response is not well understood. This paper therefore highlights the effect of replacing wake meandering with spatially varying statistics (“profile functions”) in the inflow to a downstream turbine. Profile functions at different downstream and lateral locations are extracted from a large-eddy simulation with an upstream turbine and compared with two lower-fidelity models: one that prescribes both the mean and standard deviation of the turbulence and one that prescribes only the mean. The aeroelastic response of an NREL 5 MW wind turbine is simulated with the three different wake-model fidelities, and various quantities of interest are compared. The mean values for the power and rotor speed for the medium-and low-fidelity model match well, but the accuracy of the fatigue loads varies greatly depending on the load channel. Prescribing the profile function for the standard deviation is only beneficial for the tower-base fore-aft moment; all other DELs had similar accuracies for both the medium- and low-fidelity models. The paper concludes that blade DELs can be estimated using these simple models with some accuracy, but care should be taken with the load channels related to the shaft torsion and tower-base fore-aft bending moment.


  • Open Access

    SC: Structural Damping Role

    by Leonardo Bergami

  • High‐fidelity linear time‐invariant model of a smart rotor with adaptive trailing edge flaps

    by Leonardo Bergami, Morten H. Hansen

    A high‐fidelity linear time‐invariant model of the aero‐servo‐elastic response of a wind turbine with trailing‐edge flaps is presented and used for systematic tuning of an individual flap controller. The model includes the quasi‐steady aerodynamic effects of trailing‐edge flaps on wind turbine blades and is integrated in the linear aeroelastic code HAWCStab2. The dynamic response predicted by the linear model is validated against non‐linear simulations, and the quasi‐steady assumption does not cause any significant response bias for flap deflection with frequencies up to 2–3 Hz. The linear aero‐servo‐elastic model support the design, systematic tuning and model synthesis of smart rotor control systems. As an example application, the gains of an individual flap controller are tuned using the Ziegler–Nichols method for the full‐order poles. The flap controller is based on feedback of inverse Coleman transformed and low‐pass filtered flapwise blade root moments to the cyclic flap angles through two proportional‐integral controllers. The load alleviation potential of the active flap control, anticipated by the frequency response of the linear closed‐loop model, is also confirmed by non‐linear time simulations. The simulations report reductions of lifetime fatigue damage up to 17% at the blade root and up to 4% at the tower bottom. Copyright © 2016 John Wiley & Sons, Ltd.


  • Sizing and control of trailing edge flaps on a smart rotor for maximum power generation in low fatigue wind regimes

    by Jeroen Smit, Lars O. Bernhammer, Sachin T. Navalkar, Leonardo Bergami, Mac Gaunaa


  • Open Access

    Modeling dynamic stall on wind turbine blades under rotationally augmented flow fields

    by Srinivas Guntur, Niels N. Sørensen, Scott Schreck, Leonardo Bergami

    This paper presents an investigation of two well‐known aerodynamic phenomena, rotational augmentation and dynamic stall, together in the inboard parts of wind turbine blades. This analysis is carried out using the following: (1) the National Renewable Energy Laboratory's Unsteady Aerodynamics Experiment Phase VI experimental data, including constant as well as continuously pitching blade conditions during axial operation; (2) data from unsteady delayed detached eddy simulations (DDES) carried out using the Technical University of Denmark's in‐house flow solver Ellipsys3D; and (3) data from a reduced order dynamic stall model that uses rotationally augmented steady‐state polars obtained from steady Phase VI experimental sequences, instead of the traditional two‐dimensional, non‐rotating data. The aim of this work is twofold. First, the blade loads estimated by the DDES simulations are compared with three select cases of the N‐sequence experimental data, which serves as a validation of the DDES method. Results show reasonable agreement between the two data in two out of three cases studied. Second, the dynamic time series of the lift and the moment polars obtained from the experiments are compared with those from the dynamic stall model. This allowed the differences between the stall phenomenon on the inboard parts of harmonically pitching blades on a rotating wind turbine and the classic dynamic stall representation in two‐dimensional flow to be investigated. Results indicated a good qualitative agreement between the model and the experimental data in many cases, which suggests that the current two‐dimensional dynamic stall model as used in blade element momentum‐based aeroelastic codes may provide a reasonably accurate representation of three‐dimensional rotor aerodynamics when used in combination with a robust rotational augmentation model. Copyright © 2015 John Wiley & Sons, Ltd.


  • Aerodynamic response of an airfoil section undergoing pitch motion and trailing edge flap deflection: a comparison of simulation methods

    by Leonardo Bergami, Vasilis A. Riziotis, Mac Gaunaa

    The study presents and compares aerodynamic simulations for an airfoil section with an adaptive trailing edge flap, which deflects following a smooth deformation shape. The simulations are carried out with three substantially different methods: a Reynolds‐averaged Navier–Stokes solver, a viscous–inviscid interaction method and an engineering dynamic stall model suitable for implementation in aeroelastic codes based on blade element momentum theory. The aerodynamic integral forces and pitching moment coefficients are first determined in steady conditions, at angles of attack spanning from attached flow to separated conditions and accounting for the effects of flap deflection; the steady results from the Navier–Stokes solver and the viscous–inviscid interaction method are used as input data for the simpler dynamic stall model. The paper characterizes then the dynamics of the unsteady forces and moments generated by the airfoil undergoing harmonic pitching motions and harmonic flap deflections. The unsteady aerodynamic coefficients exhibit significant variations over the corresponding steady‐state values. The dynamic characteristics of the unsteady response are predicted with an excellent agreement among the investigated methods at attached flow conditions, both for airfoil pitching and flap deflection. At high angles of attack, where flow separation is encountered, the methods still depict similar overall dynamics, but larger discrepancies are reported, especially for the simpler engineering method. Copyright © 2014 John Wiley & Sons, Ltd.


  • A smart rotor configuration with linear quadratic control of adaptive trailing edge flaps for active load alleviation

    by Leonardo Bergami, Niels K. Poulsen

    The paper proposes a smart rotor configuration where adaptive trailing edge flaps (ATEFs) are employed for active alleviation of the aerodynamic loads on the blades of the NREL 5 MW reference turbine. The flaps extend for 20% of the blade length and are controlled by a linear quadratic (LQ) algorithm based on measurements of the blade root flapwise bending moment. The control algorithm includes frequency weighting to discourage flap activity at frequencies higher than 0.5 Hz. The linear model required by the LQ algorithm is obtained from subspace system identification; periodic disturbance signals described by simple functions of the blade azimuthal position are included in the identification to avoid biases from the periodic load variations observed on a rotating blade. The LQ controller uses the same periodic disturbance signals to handle anticipation of the loads periodic component. The effects of active flap control are assessed with aeroelastic simulations of the turbine in normal operation conditions, as prescribed by the International Electrotechnical Commission standard. The turbine lifetime fatigue damage equivalent loads provide a convenient summary of the results achieved with ATEF control: 10% reduction of the blade root flapwise bending moment is reported in the simplest control configuration, whereas reductions of approximately 14% are achieved by including periodic loads anticipation. The simulations also highlight impacts on the fatigue damage loads in other parts of the structure, in particular, an increase of the blade torsion moment and a reduction of the tower fore‐aft loads. Copyright © 2014 John Wiley & Sons, Ltd.