Jia-Hong Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jia-Hong Sun has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Tsung-Tsong Wu
Institute of Applied Mechanics, National Taiwan University, Taipei, Taiwan
3 shared publicationsYuan-Hai Yu
Chang Gung University
3 shared publicationsC.-C. Lin
Department of Mechanical Engineering Chang Gung University Taoyuan Taiwan
1 shared publicationFeng-Chia Hsu
National Taiwan University Institute of Applied Mechanics Taipei 106, Taiwan
1 shared publicationHao-Wei Lin
1 shared publication- I Ling Chang
National Cheng Kung University
1 shared publication
Latest Publications
- Open Access
- 10 June 2026
- Published by Elsevier in SSRN Electronic Journal
Acoustic Metasurfaces Enabled by Rotating-Partition Helmholtz Resonators
Acoustic metasurfaces based on Helmholtz resonators commonly achieve phase control through geometric variations, which can limit structural flexibility and adaptability. In this study, we propose and experimentally validate a new phase-generation mechanism enabled by rotational internal partitions embedded within Helmholtz resonators. By rotating the internal partition, the effective acoustic path inside the resonator cavity is modified, producing a controllable phase shift in the transmitted wave while preserving the external geometry of the unit cell. Finite element simulations establish a clear relationship among partition angle, phase shift, and transmission characteristics at 5500 Hz, demonstrating substantial phase modulation with relatively high transmission efficiency.Based on the derived angle–phase mapping, metasurfaces with prescribed phase gradients are designed to realize representative acoustic functionalities, including focusing and directed refraction. Although the current configuration does not achieve full 2π phase coverage, the available phase variation is sufficient to produce effective wavefront manipulation. Numerical results demonstrate clear acoustic focusing and directional refraction through appropriate partition-angle distributions. A focusing metasurface was further fabricated using three-dimensional printing and tested in a customized impedance chamber. The experimental measurements show good agreement with the simulations, confirming the feasibility of the proposed rotation-induced phase-control mechanism. This work establishes rotational-partition Helmholtz resonators as physically intuitive and structurally efficient phase-control elements, providing a promising foundation for multifunctional and potentially mechanically reconfigurable acoustic metasurfaces.
- 10 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAcoustic Metasurfaces Enabled by Rotating-Partition Helmholtz Resonators
Acoustic metasurfaces based on Helmholtz resonators commonly achieve phase control through geometric variations, which can limit structural flexibility and adaptability. In this study, we propose and experimentally validate a new phase-generation mechanism enabled by rotational internal partitions embedded within Helmholtz resonators. By rotating the internal partition, the effective acoustic path inside the resonator cavity is modified, producing a controllable phase shift in the transmitted wave while preserving the external geometry of the unit cell. Finite element simulations establish a clear relationship among partition angle, phase shift, and transmission characteristics at 5500 Hz, demonstrating substantial phase modulation with relatively high transmission efficiency.Based on the derived angle–phase mapping, metasurfaces with prescribed phase gradients are designed to realize representative acoustic functionalities, including focusing and directed refraction. Although the current configuration does not achieve full 2π phase coverage, the available phase variation is sufficient to produce effective wavefront manipulation. Numerical results demonstrate clear acoustic focusing and directional refraction through appropriate partition-angle distributions. A focusing metasurface was further fabricated using three-dimensional printing and tested in a customized impedance chamber. The experimental measurements show good agreement with the simulations, confirming the feasibility of the proposed rotation-induced phase-control mechanism. This work establishes rotational-partition Helmholtz resonators as physically intuitive and structurally efficient phase-control elements, providing a promising foundation for multifunctional and potentially mechanically reconfigurable acoustic metasurfaces.
- Open Access
Ensemble Machine Learning Model for Accurate Air Pollution Detection Using Commercial Gas Sensors
This paper presents the results on developing an ensemble machine learning model to combine commercial gas sensors for accurate concentration detection. Commercial gas sensors have the low-cost advantage and become key components of IoT devices in atmospheric condition monitoring. However, their native coarse resolution and poor selectivity limit their performance. Thus, we adopted recurrent neural network (RNN) models to extract the time-series concentration data characteristics and improve the detection accuracy. Firstly, four types of RNN models, LSTM and GRU, Bi-LSTM, and Bi-GRU, were optimized to define the best-performance single weak models for CO, O3, and NO2 gases, respectively. Next, ensemble models which integrate multiple single weak models with a dynamic model were defined and trained. The testing results show that the ensemble models perform better than the single weak models. Further, a retraining procedure was proposed to make the ensemble model more flexible to adapt to environmental conditions. The significantly improved determination coefficients show that the retraining helps the ensemble models maintain long-term stable sensing performance in an atmospheric environment. The result can serve as an essential reference for the applications of IoT devices with commercial gas sensors in environment condition monitoring.
Open AccessEnsemble Machine Learning Model for Accurate Air Pollution Detection Using Commercial Gas Sensors
This paper presents the results on developing an ensemble machine learning model to combine commercial gas sensors for accurate concentration detection. Commercial gas sensors have the low-cost advantage and become key components of IoT devices in atmospheric condition monitoring. However, their native coarse resolution and poor selectivity limit their performance. Thus, we adopted recurrent neural network (RNN) models to extract the time-series concentration data characteristics and improve the detection accuracy. Firstly, four types of RNN models, LSTM and GRU, Bi-LSTM, and Bi-GRU, were optimized to define the best-performance single weak models for CO, O3, and NO2 gases, respectively. Next, ensemble models which integrate multiple single weak models with a dynamic model were defined and trained. The testing results show that the ensemble models perform better than the single weak models. Further, a retraining procedure was proposed to make the ensemble model more flexible to adapt to environmental conditions. The significantly improved determination coefficients show that the retraining helps the ensemble models maintain long-term stable sensing performance in an atmospheric environment. The result can serve as an essential reference for the applications of IoT devices with commercial gas sensors in environment condition monitoring.
- 23 January 2018
- Published by Springer Nature in Applied Physics A
- Vol. 124 (2) , 165
Anisotropic surface acoustic waves in tungsten/lithium niobate phononic crystals
- 23 January 2018
- Published by Springer Nature in Applied Physics A
- Vol. 124 (2) , 165
Anisotropic surface acoustic waves in tungsten/lithium niobate phononic crystals
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Phononic lens for suppressing diffraction of surface wave in lithium niobate substrate
Surface acoustic wave (SAW) devices are widely used as acoustic-electronic components today. The lithium niobate was often used as the substrate of SAW devices for its higher electromechanical coupling coefficient. In some applications like RFID tags and sensors, SAW devices have a long delay line and the energy loss of diffraction is considerable. Phononic crystals (PnC) have properties of band gaps and anisotropic propagation. Band gaps were proposed as filters, reflective gratings, and waveguide [1-2]. In our previous study, self-collimation of SAW propagating in a tungsten/lithium niobate PnC was studied, and a PnC delay line was used to lower beam spreading [3]. In this paper, we further analyze the anisotropic SAWs in PnCs systematically and then phononic lenses were designed to suppress diffraction in SAW devices.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Phononic lens for suppressing diffraction of surface wave in lithium niobate substrate
Surface acoustic wave (SAW) devices are widely used as acoustic-electronic components today. The lithium niobate was often used as the substrate of SAW devices for its higher electromechanical coupling coefficient. In some applications like RFID tags and sensors, SAW devices have a long delay line and the energy loss of diffraction is considerable. Phononic crystals (PnC) have properties of band gaps and anisotropic propagation. Band gaps were proposed as filters, reflective gratings, and waveguide [1-2]. In our previous study, self-collimation of SAW propagating in a tungsten/lithium niobate PnC was studied, and a PnC delay line was used to lower beam spreading [3]. In this paper, we further analyze the anisotropic SAWs in PnCs systematically and then phononic lenses were designed to suppress diffraction in SAW devices.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
A SAW filter using SiO2/LiNbO3 layered-structure phononic crystals
Phononic crystal (PnC) in half-space allows anisotropic propagation and band gaps for surface acoustic wave (SAW) and promise applications such as filters and reflectors. For the feasible MEMS fabrication, a PnC comprised of cylindrical holes in a SiO 2 layer covering a 128°rotated Y-cut LiNbO 3 substrate was applied and the acoustic modes were analyzed numerically. The band gap for SAW was indicated and the PnC was used as reflective gratings to construct SAW resonators. By tuning the cavity length, the resonant frequency was controlled. Then a ladder-type bandpass filter at 933-947 MHz was defined by two phononic SAW resonators. The result showed feasibility of applying PnC in acoustic electronics devices.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
A SAW filter using SiO2/LiNbO3 layered-structure phononic crystals
Phononic crystal (PnC) in half-space allows anisotropic propagation and band gaps for surface acoustic wave (SAW) and promise applications such as filters and reflectors. For the feasible MEMS fabrication, a PnC comprised of cylindrical holes in a SiO 2 layer covering a 128°rotated Y-cut LiNbO 3 substrate was applied and the acoustic modes were analyzed numerically. The band gap for SAW was indicated and the PnC was used as reflective gratings to construct SAW resonators. By tuning the cavity length, the resonant frequency was controlled. Then a ladder-type bandpass filter at 933-947 MHz was defined by two phononic SAW resonators. The result showed feasibility of applying PnC in acoustic electronics devices.
- Open Access
- 9 February 2016
- Published by Oxford University Press (OUP) in Journal of Mechanics
- Vol. 32 (4) , 435-440
Wireless Saw-Based Tags with Temperature Sensors that Utilize High-Resolution Delay-Time Measurements
Surface acoustic wave (SAW) devices are widely used in commercial products as filters and resonators. SAW devices are also applied as passive, wireless radio frequency identification (RFID) tags and sensors, which can be used in harsh environments and consume no batteries. In this study, we designed and fabricated an SAW-based RFID tag with the added function of a high-resolution temperature sensor. A coupling of modes model was adopted to design 433MHz SAW-based tags/sensors. An improved signal processing method was used to increase the resolution of time-domain signals, enabling the slight change of delay time caused by temperature variation to be detected. Subsequently, the SAW tags/sensors were fabricated on 128° Y-cut lithium niobate and used to detect temperature shifts. The results revealed that high-resolution delay-time SAW devices are feasible for measuring temperatures precisely and can be applied to other SAW-based sensors.
- 9 February 2016
- Published by Oxford University Press (OUP) in Journal of Mechanics
- Vol. 32 (4) , 435-440
Open AccessWireless Saw-Based Tags with Temperature Sensors that Utilize High-Resolution Delay-Time Measurements
Surface acoustic wave (SAW) devices are widely used in commercial products as filters and resonators. SAW devices are also applied as passive, wireless radio frequency identification (RFID) tags and sensors, which can be used in harsh environments and consume no batteries. In this study, we designed and fabricated an SAW-based RFID tag with the added function of a high-resolution temperature sensor. A coupling of modes model was adopted to design 433MHz SAW-based tags/sensors. An improved signal processing method was used to increase the resolution of time-domain signals, enabling the slight change of delay time caused by temperature variation to be detected. Subsequently, the SAW tags/sensors were fabricated on 128° Y-cut lithium niobate and used to detect temperature shifts. The results revealed that high-resolution delay-time SAW devices are feasible for measuring temperatures precisely and can be applied to other SAW-based sensors.
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23271914,p. 1-4
Surface acoustic wave resonator using layered phononic crystals
Phononic crystals (PnC) perform band gaps and promise applications such as filters and reflectors. Traditional PnC for surface acoustic waves (SAW) consisting of deep periodic holes in half space. To apply PnCs in SAW devices, the feasibility of fabrication was considered and layered PnCs were proposed. In this paper, a PnC comprised of cylindrical holes in a SiO 2 layer covering a 128°rotated Y-cut LiNbO 3 substrate was analyzed numerically and used to design SAW resonators. Acoustic dispersion of SAWs in the PnC was calculated by finite element method and the band gap range was indicated. The band gaps were manipulated by the layer thickness and cylinder size. Then the layered PnC was applied as gratings to reflect SAWs. Resonant cavities for SAW were further designed, and a 942.875 MHz SAW resonator with Q-factor of 433 was obtained. The result showed feasibility of applying PnC in acoustic electronics devices via MEMS fabrication.
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23271914,p. 1-4
Surface acoustic wave resonator using layered phononic crystals
Phononic crystals (PnC) perform band gaps and promise applications such as filters and reflectors. Traditional PnC for surface acoustic waves (SAW) consisting of deep periodic holes in half space. To apply PnCs in SAW devices, the feasibility of fabrication was considered and layered PnCs were proposed. In this paper, a PnC comprised of cylindrical holes in a SiO 2 layer covering a 128°rotated Y-cut LiNbO 3 substrate was analyzed numerically and used to design SAW resonators. Acoustic dispersion of SAWs in the PnC was calculated by finite element method and the band gap range was indicated. The band gaps were manipulated by the layer thickness and cylinder size. Then the layered PnC was applied as gratings to reflect SAWs. Resonant cavities for SAW were further designed, and a 942.875 MHz SAW resonator with Q-factor of 433 was obtained. The result showed feasibility of applying PnC in acoustic electronics devices via MEMS fabrication.
- 1 October 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 145-154
Phononic plate waves
In the past two decades, phononic crystals (PCs) which consist of periodically arranged media have attracted a lot of interests due to the existence of complete frequency band gaps and maneuverable band structures. Recently, Lamb waves in thin plates with PC structures started to receive increasing attention for their potential applications in filters, resonators, and waveguides. This paper presents a review of recent works conducted by the authors and co-workers on this topic. Both theoretical and experimental studies of Lamb waves in two-dimensional (2D) PC plate structures are covered. On the theoretical side, analyses of Lamb waves in 2D phononic plates using the plane wave expansion (PWE) method, finite-difference time-domain (FDTD) method, and finite-element (FE) method are briefly addressed. These methods were applied to determine the frequency ranges of the complete band gaps of Lamb waves, characteristics of the propagating and localized eigenmodes that can exist in the PC plate structures, and behavior of anomalous refraction called negative refraction. The theoretical analyses demonstrated the effects of PC based negative refraction, lens, waveguides, and resonant cavities. We also discuss the influences of geometrical parameters on the guiding and resonance efficiency and the frequencies of waveguide and cavity modes. On the experimental side, we present design and fabrication of a silicon based Lamb wave resonator which utilizes PC plates as reflective gratings to form the resonant cavity of Lamb waves. The measured results showed significant improvement of the insertion losses and quality factors of the resonators when the PCs are applied.
- 1 October 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 145-154
Phononic plate waves
In the past two decades, phononic crystals (PCs) which consist of periodically arranged media have attracted a lot of interests due to the existence of complete frequency band gaps and maneuverable band structures. Recently, Lamb waves in thin plates with PC structures started to receive increasing attention for their potential applications in filters, resonators, and waveguides. This paper presents a review of recent works conducted by the authors and co-workers on this topic. Both theoretical and experimental studies of Lamb waves in two-dimensional (2D) PC plate structures are covered. On the theoretical side, analyses of Lamb waves in 2D phononic plates using the plane wave expansion (PWE) method, finite-difference time-domain (FDTD) method, and finite-element (FE) method are briefly addressed. These methods were applied to determine the frequency ranges of the complete band gaps of Lamb waves, characteristics of the propagating and localized eigenmodes that can exist in the PC plate structures, and behavior of anomalous refraction called negative refraction. The theoretical analyses demonstrated the effects of PC based negative refraction, lens, waveguides, and resonant cavities. We also discuss the influences of geometrical parameters on the guiding and resonance efficiency and the frequencies of waveguide and cavity modes. On the experimental side, we present design and fabrication of a silicon based Lamb wave resonator which utilizes PC plates as reflective gratings to form the resonant cavity of Lamb waves. The measured results showed significant improvement of the insertion losses and quality factors of the resonators when the PCs are applied.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 515-520
Band gap materials and micro-phononic devices
This paper presents simulation, design and fabrication of surface acoustic wave (SAW) and Lamb wave micro-phononic devices. To illustrate the band gap formation and possible applications, numerical simulations on the air/silicon phononic crystals (PCs) were conducted which include: surface acoustic waves (SAWs) in a half-space and Lamb waves in a plate. With a lattice constant of 20 μm and high filling fraction, complete band gaps in the range of hundred MHz were found. Based on the band gap properties, numerical simulations on the point defects, waveguides and cavities in PC plates were then performed and discussed. On the experimental side, the associated micro acoustic resonators for both SAW and Lamb waves are demonstrated. Results on the fabrication and measurements of the silicon based micro-PC devices in the hundred MHz ranges are encouraging and may find potential applications in the areas of wireless filters.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 515-520
Band gap materials and micro-phononic devices
This paper presents simulation, design and fabrication of surface acoustic wave (SAW) and Lamb wave micro-phononic devices. To illustrate the band gap formation and possible applications, numerical simulations on the air/silicon phononic crystals (PCs) were conducted which include: surface acoustic waves (SAWs) in a half-space and Lamb waves in a plate. With a lattice constant of 20 μm and high filling fraction, complete band gaps in the range of hundred MHz were found. Based on the band gap properties, numerical simulations on the point defects, waveguides and cavities in PC plates were then performed and discussed. On the experimental side, the associated micro acoustic resonators for both SAW and Lamb waves are demonstrated. Results on the fabrication and measurements of the silicon based micro-PC devices in the hundred MHz ranges are encouraging and may find potential applications in the areas of wireless filters.