PHPer Hallander

Per Hallander

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Per Hallander has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Sensing of transverse pressure in structural composite by impedance spectroscopy on embedded carbon nanotube sensing structures

    by Tobias Karlsson, Patrick Janus, Per Hallander, Malin Åkermo

    Next-generation aerospace composite structures are expected to evolve from purely mechanical systems into multifunctional structures by integrating additional functionalities through the embedment of functional filler materials. One promising approach is the incorporation of carbon nanotubes (CNTs) to add sensing capabilities. In this paper, two CNT-based sensing structures are evaluated for transverse pressure sensing up to 20 MPa when embedded in an aerospace-grade glass fibre/epoxy laminate. In pursuit of higher sensing sensitivity, a shift from direct current (DC) to alternating current (AC) based sensing is implemented, enabling the exploration of frequency-dependent sensing behaviour. With this transition, a characterisation and measurement procedure is presented and justified, determining resistive and polarisation effects present in the sensing configurations and evaluating their susceptibility to stray capacitance prior to pressure sensing. The first sensing structure, using embedded Vertically Aligned CNT (VACNT) forests, exhibits pressure sensitivity with the resistive sensitivity increasing at frequencies above the critical frequency of the system, justifying the shift from DC to AC. The reactance shows similar pressure sensitivity except for in a region near 1 MHz, where it becomes pressure insensitive. The second sensing structure, consisting of two embedded VACNT forests separated by a Kapton film, emulates a capacitor. Its impedance shows a Kapton-dominated frequency range and a CNT-dominated range, with a transition region in between. Consequently, the pressure response becomes frequency-dependent, as the two constituents not only dominate different frequency ranges but also exhibit different sensitivities to pressure.


  • A Wide-Scanning Array Antenna of Connected Vertical Bowtie Elements Structurally Integrated Within an Aircraft Fuselage

    by Prabhat Khanal, Jian Yang, Marianna Ivashina, Anders Höök, Ruoshan Luo, Per Hallander, Mussie Gebretnsae

    A low-profile, wide-scanning phased-array antenna of vertical bowtie elements fully integrated with a structurally efficient radome and ribs of an aircraft fuselage is proposed in this paper. The array is designed to simultaneously fulfil the electrical requirements of an airborne antenna sensor and the mechanical requirements of a load-carrying aircraft fuselage. The array antenna is capable of steering the beam up to ±80° in the azimuth plane over a 20% bandwidth (2.4 GHz to 3 GHz) with the active reflection coefficient (Γ act ) below –10 dB in an infinite array environment. Experimental results of a 16×16 element array demonstrator agree well with the simulation results. The 16×16 array antenna is capable of steering the beam up to ±60° and ±75° with the bandwidth of 20% and 10%, respectively at Γ act ≤ –10 dB. The array antenna also achieved good stiffness and performed well in the vibration loads of commercial transport aircraft.


  • Open Access

    Vacuum-Assisted Hot-Forming Using Tailored Laminate Temperature

    by Tommy Grankäll, Per Hallander, Malin Åkermo

    A non-isothermal vacuum assisted hot-forming process using tailored laminate temperature is introduced. By using process simulation and manufacturing experiments, improved laminate quality is achieved compared to the standard hot-forming process. Furthermore, it is also shown that the manufacturing time in the clean room can be reduced to one tenth of the standard process time. In this study 8.4 mm thick quasi-isotropic laminates from unidirectional prepreg were laid up flat with an automatic tape laying machine and hot-formed to a U-shaped laminate. The laminates were then cured in a concave mould with standard bag on the inside. A complete tailored temperature hot-forming cycle of 7.5 min produced a very good final laminate quality with a total thickness variation as low as 4.0% and without wrinkles or indications of porosity. With a 4 min hot-forming cycle the thickness variation was also acceptable at 8%.


  • Open Access

    Using tailored temperature variations to obtain flawless forming of multi-stacked unidirectional prepreg

    by Per Hallander, Tommy Grankäll, Matilda Eriksson, Mikael Petersson, Malin Åkermo

    In this article, tailored temperature zones are used to obtain improved quality during rapid, high pressure forming of multi-stacked unidirectional prepreg. Particularly in aerospace applications, commonly used forming processes for multi-stacked unidirectional prepreg are often considered a bottleneck in production since the forming cycle requires both heating and cooling ramps and consequently takes long time—often about 1 h. It is possible to speed up the process by using elevated pressure and temperature. However, higher pressure and temperature also increase the influence of pressure gradient-driven, in-plane material movement (squeeze flow). This typically appears as radius thinning when forming a C-spar geometry on a male mold. Decrease of lay-up temperature will decrease radius thinning, but due to obstructed interply slippage, instead bending-induced wrinkles appear on the spar flange. In this article, tailored temperatures at the radius and in the flange area are introduced by using a hot lay-up and a cold mold. The results show that temperature differences of 6℃–10℃ between the radius area and the flange edge of the lay-up decreases radius thinning while still avoiding bending-induced wrinkles. Except from the radius temperature also the stacking sequence and the choice of prepreg system showed a significant influence on the radius thinning.


  • Fast forming of multistacked UD prepreg using a high‐pressure process

    by Per Hallander, Jens Sjölander, Mikael Petersson, Tomas Andersson, Malin Åkermo

    In this article, the opportunities of fast forming of multistacked UD prepreg when using high‐pressure forming were examined in an experimental study. Forming is often considered a bottleneck in manufacturing of composite aircraft parts and speeding up the process is, therefore, of great interest. A Quintus Flexform fluid cell press was used to create pressure of 100 to 400 bars. In the study, different lay‐up sequences and thicknesses were tested for manufacturing of c‐shaped coupons. Tests were performed at different temperatures and some of the samples were sandwiched with mild steel sheets referred to as a steel sheet dummy. A case study was also performed on a double‐curved spar geometry. It was found that forming at a relatively high overall pressure level combined with an elevated temperature, created squeeze flow‐related wrinkle formations, and radius thinning. With high pressure forming, material compression/compaction mechanisms showed to have great influence on the forming result. This differs to low pressure vacuum forming, where intraply shear, interply shear, and ply bending are the dominant forming mechanisms. The steel sheet dummy minimized the squeeze flow related wrinkle in the web and flanges. Instead the forming temperature was found to exert the greatest influence on radius thinning. When forming at room temperature, radius thinning was almost eliminated and instead bending‐related wrinkles in the flange below the radii appeared. POLYM. COMPOS., 40:3550–3561, 2019. © 2019 Society of Plastics Engineers


  • Forming of composite spars including interlayers of aligned, multiwall, carbon nanotubes: An experimental study

    by P. Hallander, J. Sjölander, M. Åkermo

    Carbon nanotubes offer the potential for improved or changed matrix properties, thereby enabling the creation of novel, multifunctional composite materials. By using highly aligned, multiwall, carbon nanotubes (MWCNT) with thermoset resins, good dispersion and distribution of nanotubes is obtained. To date, research has mainly focused on improving the growth process of the aligned MWCNTs, however little has been done on the processing of composites that include MWCNTs as interlayers in the stack. The aim of this work is to study how the aligned MWCNTs are affected within composite part forming. The study shows that MWCNTs are influenced by the shearing that occurs during forming, but still maintain their integrity. To some extent, the shear pattern observed in the MWCNTs after deformation provides an indication of deformation modes. However, the presence of MWCNTs also significantly influences the forming characteristics of the prepreg stack. POLYM. COMPOS., 39:181–191, 2018. © 2016 Society of Plastics Engineers