JMJavad Soleiman Meiguni

Javad Soleiman Meiguni

*This is an algorithmically generated author record based on publicly available information.

Javad Soleiman Meiguni has a total of 61 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • ESD Events to Wearable Medical Devices in Healthcare Environments—Part 1: Current Measurements

    by Mehdi Kohani, Javad Meiguni, David J. Pommerenke, Michael G. Pecht

    Wearable medical devices are widely used for monitoring and treatment of patients. Electrostatic discharge can render these devices unreliable and cause a temporary or permanent disturbance in their operation. In a healthcare environment, severe electrostatic discharge (ESD) can occur while a patient, lying down or sitting on a hospital bed with a wearable device, discharges the device via a grounded bedframe. To protect the devices from ESD damage, the worst-case discharge conditions in the usage environment need to be identified. Previous studies by authors revealed that such events could be more severe than the conventional human metal model (HMM). However, the impact of various body postures and device location on the body and the severity of the discharge current compared with HMM have not been investigated for healthcare environments. This study is an attempt to address the gap in the literature by investigating severe discharges in such environments and characterizing their current waveforms for three postures (standing on the floor, sitting, and lying down on a hospital bed), two device locations (hand and waist), and four body voltages (2, 4, 6, and 8 kV). This study highlights that the IEC 61000-4-2 standard may not be sufficient for testing wearable medical devices.


  • Electromagnetic Transmit Array With Optical Control for Beamforming

    by Wei Zhang, Javad Meiguni, Yin Sun, Muqi Ouyang, Xin Yan, Xu Wang, Reza Yazdani, Daryl Beetner, Donghyun Kim, David Pommerenke

    This proof-of-concept paper demonstrates the feasibility of using a slide projector to steer the beam of a transmit array by adding solar cells and varactor diodes to each unit cell. By irradiating each solar cell with the light of different intensities from a slide projector, the measured phase of the wave transmitted by the 4×4 transmit array shifts within 92° at 4.26 GHz, while the variation in magnitude is measured within 4 dB. Different light configurations are identified via a searching algorithm to achieve peak/null beamforming in a particular direction. The beam of the prototypical 4×4 transmit array can be shifted by ±24° in terms of the peaks and -30° to 36° in terms of the nulls. The concept of adding light modulation to the transmit array with a slide projector can provide update rates of 10s of milliseconds with control of brightness and color distributed over a large area of the array.


  • Open Access

    Inverse MoM Approach to Near-Field Prediction and RFI Estimation in Electronic Devices With Multiple Radiating Elements

    by Shiva Hayati Raad, Javad Soleiman Meiguni, Raj Mittra

    An inverse method of moments (MoM) approach is developed to estimate the equivalent electric/magnetic current sources to predict radio frequency interference (RFI) in electronic devices. The proposed method is designed to reconstruct the noise sources in electronic devices containing multiple radiating elements by using a finite metal object carrying electric surface currents. The surface current elements are further applied to calculate the electromagnetic fields on arbitrary observation planes near the device under test (DUT). The method is validated through numerical simulation examples, including electric-type CPU noise, magnetic-type non-planar HDMI connector noise, printed circuit board (PCB) with Wi-Fi and PIFA antennas, and heat sink embedded in the DUT. The results confirm less than 0.4 dB difference in the predicted pattern at the antenna operating frequency when a triangular segmentation is applied in the vicinity of the noise source area, and the equivalent surface current is calculated at the edges of the Rao-Wilton-Glisson (RWG) meshes. The proposed method is a promising ’source reconstruction’ candidate for predicting the near-field radiation characteristics of electronic devices with multiple peaks and nulls in the near-field radiation pattern. The method helps estimate the level of RFI by summing up the contributions of all the dipoles of the equivalent noise source derived by solving forward and inverse problems. The RFI results based on the inverse MoM approach are validated by comparing them with those obtained from CST simulation, and good agreement is achieved between the two.


  • Improved SEED Modeling of an ESD Discharge to a USB Cable

    by Yang Xu, Jianchi Zhou, Sergej Bub, Steffen Holland, Javad Soleiman Meiguni, David Pommerenke, Daryl G. Beetner

    Integrated circuits (ICs) connected to a universal serial bus (USB) interface require robust electrostatic discharge (ESD) protection strategies due to the nature of the high-speed interface and the regular access by users. System-efficient ESD design (SEED) simulations can help predict the level of ESD stress seen by the IC when protected by a transient voltage suppressor (TVS). In the following paper, previously developed models were improved to predict the voltage and current seen by a TVS and an on-chip protection diode when an ESD gun was discharged to one USB cable pin. Models were improved, in part, by accurately modeling the conductivity modulation within the behavioral TVS model and by using a measured equivalent source to represent the complex interaction between the ESD gun, USB cable, and enclosure. The response of the TVS and on-chip diode was studied in simulation and measurement for several cable configurations and when adding passive components between the TVS and on-chip diode. Simulations predicted peak and quasi-static voltages and currents at the TVS and on-chip diode within 30% of those seen in measurements. The proposed modeling process can help engineers to evaluate and optimize the effectiveness of their ESD protection strategies under complicated test conditions.


  • Transient Response of ESD Protection Devices for a High-Speed I/O Interface

    by Jianchi Zhou, Yang Xu, Sergej Bub, Steffen Holland, Javad Soleiman Meiguni, David Pommerenke, Daryl G. Beetner

    System-efficient electrostatic discharge (ESD) design (SEED) models of a diode and transient voltage suppressor (TVS) were developed to study their transient response in a high-speed input/output interface. Previously reported SEED models were improved to strengthen their convergence stability and facilitate accurate predictions over a wide range of conditions. These improvements were required to accurately capture the race conditions between the TVS and on -chip diode, where the diode's turn on may prevent turn on of the TVS. Simulations and measurements were performed to demonstrate the impact of the ESD pulse's rise time on race conditions. During a race, results showed the worst-case quasi-static diode current could be twice as high for long rise-time pulses than for short rise-times where the TVS does not turn on , and on -chip diode current may be larger at low test voltages than at high test voltages where the TVS does turn on . Adding a small passive impedance between the external TVS and the on -chip diode helps the TVS turn on and reduce the current through the on -chip diode by more than 50%. Similarly, lengthening the trace between the TVS and diode could reduce on -chip diode current by up to a factor of two.


  • Transient Analysis of ESD Protection Circuits for High-Speed ICs

    by Javad Soleiman Meiguni, Jianchi Zhou, Giorgi Maghlakelidze, Yang Xu, Omid Hoseini Izadi, Shubhankar Marathe, Li Shen, Sergej Bub, Steffen Holland, Daryl G. Beetner, et al.

    Electrostatic discharge (ESD) failures in high-speed integrated circuits (ICs) cause critical reliability problems in electronic devices. Transient voltage suppressor (TVS) diodes are installed on high-speed I/O traces to improve system-level ESD protection. To protect the circuit, the majority of ESD current must flow into the external TVS diode rather than into the IC, but due to turn- on behavior, the TVS diode may not snap back when needed and the IC's internal protection may take most of the current. These race conditions between the internal and external ESD protection circuits were investigated for a universal serial bus(USB) interface board. The transient turn- on behavior of the on-chip and off-chip protection circuitry was characterized by measurements and by system efficient ESD design (SEED) simulations. The effect of transmission line pulses (TLP pulses) and power supply voltages of different sizes on the response of the protection circuitry were monitored and compared with SEED simulations. SEED models showed good agreement with measurements and were used to study the impact of passive components added to a high-speed trace or within the IC package on the ESD protection response. Results show the importance of properly accounting for the parasitic resistance and inductance between the on-chip diode and off-chip TVS diode, as well as the length of the transmission line when choosing the external TVS device. Results also show that testing must be performed using mid-level events to account for possible problems due to race conditions.


  • System-Level EMI of an Artificial Router System With Multiple Radiators: Prediction and Validation

    by Wei Zhang, Javad Soleiman Meiguni, Kaustav Ghosh, Abhishek Patnaik, Morten Sorensen, Ahmad Hosseinbeig, David Pommerenke, Jacques Rollin, Jing Li, Qian Liu, et al.

    In a multimodule system, an increase in the number of radiating optical modules will increase the electromagnetic emissions. This article investigates the scaled tendency of the emissions in a router system loaded with hundreds of optical modules. An artificial router mimicking the real system was built to investigate this tendency. A patch antenna array mimics the radiation of the optical modules. It can be excited in in-phase and random-phase configurations. The measurement data verifies the theoretical analysis and the prediction from a statistical method without performing hundreds of different experiments on a real router. Assuming that all radiators are radiating at the same frequency and have similar radiation pattern with random phases, the average of the maximal directivity of the system will saturate if the number of radiators (N) is larger than 14. Furthermore, the average of the maximal electric field radiated will increase following a 10 log $_{10}$ N (dB) tendency.


  • Source Reconstruction in Near-Field Scanning Using Inverse MoM for RFI Application

    by Hossein Rezaei, Javad Soleiman Meiguni, Morten Sorensen, Roman G. Jobava, Victor Khilkevich, Jun Fan, Daryl G. Beetner, David Pommerenke

    The ability to predict the electric and magnetic fields generated by a component can solve many in-system interference problems before they occur. In this article, methods are presented to predict the high-frequency near electric and magnetic fields from a component using a method of moment approach. The current representation is estimated from a near electric-field scan by solving the electric field integral equation. The reconstruction method was validated with measurements of a test board containing a buffer integrated circuit. The current representation was shown to accurately predict fields at locations both above and to the side of the buffer with less than a 3.5-dB average error. Here, a near-field scan was only performed on a flat plane above the emitter and was used to predict sources to the side of the emitter. To accurately predict fields to the side of the emitter, the current representation must be defined on a surface between the emitter and the prediction location. An error analysis was performed to understand the impact of scan plane parameters, such as the size of the scan plane, the size of the current representation, and the relative distance between the current representation and the estimated fields on prediction accuracy.


  • Compact Via-Coupling Fed Monopulse Antenna With Orthogonal Tracking Capability in Radiation Pattern

    by Seyed Amin Khatami, Javad Meiguni, Ali Amn-E Elahi, Pejman Rezaei

    A compact monopulse antenna operating at 10 GHz is presented. The feed network consists of four rat-race couplers which generate sum and difference patterns in orthogonal radiation planes (azimuth and elevation). The focus was on improving performance by improving the matching circuit to generate in-phase and out-phase excitations while also maintaining a very high null-depth, which is applicable for tracking purposes. The electromagnetic energy is transmitted from the feed network to the radiators through via-coupling structure. Using the symmetrical via-fed patch array results in low mutual coupling between the antenna ports. A prototype of the proposed antenna was manufactured on a printed circuit board and tested. A suitable agreement between the measurement and simulation results was obtained. The results show a -10-dB impedance bandwidth of 2.1%, as well as -24 dB and -20 dB null depths on the elevation and azimuth planes, respectively, in the difference mode of operation.