SYSvitlana Yushchenko

Svitlana Yushchenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Svitlana Yushchenko has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Strucrural design optimization of welded wheels of reducers during designing process

    by Serhii Oleksiienko, Mykhailo Rudenko, Svitlana Yushchenko, Iryna Nahorna

    Nowadays, due to the widespread use of CAD/CAE systems, opportunities are created for topological and parametric optimization of various designs. At the same time, the technological process of manufacturing a welded structure determines its strength characteristics. This is due to the fact that during welding there is a change in the properties of the base metal in the heat-affected zone, deformations of the structure occur and the residual stress field is created. All these changes affect the operation conditions of welded joints and can cause both an increase and decrease of the welded structure operability. In the manufacture of welded wheels of reducers, which consist of a shaft, rim and discs, steels are used that require preheating before welding – steel 41CrS4 (40Kh). Heating the rim before welding lead to the fact that a decrease in its diameter during cooling after welding causes compression of the welds joining the rim with the discs. This, in turn, positively affect the operation of these welds which are tensile under operating conditions. However, under certain structural factors, such as the outer diameter of the discs, the inner diameter of the rim, the size of the gap between these elements during welding, and depending on the preheating temperature of the rim before welding, the effect of these factors on improving performance may be different. The work developed a model that, when assessing the stress state in welded joints, allows us to take into account the presence of tensile stresses from longitudinal and transverse shrinkage. An algorithm for calculating the stress-strain state in welded wheels using CAE-systems has been developed. Influence of sizes of parts, gaps in joints and preheating temperature on value of stresses and strains in joints of disks with rims is established.

  • Open Access

    Designing of glass-silicon nodes of pressure sensors and influnce of their dimentional parameters on fracture resistance

    by Serhii Oleksiienko, Svitlana Yushchenko, Mykhailo Rudenko

    A promising method of joining silicon with glass is the solid phase welding method that can be carried out in an air atmosphere, at low temperatures, using insignificant external compression forces and with the application of an electrostatic field of high voltage. The widespread use of the method limits a significant drawback – the instability of the quality indicators of welded joints, the main of which is mechanical strength. Primarily this is due to the imperfection of the methods for determining the welding time, during which it is possible to obtain welded joints with a given level of service properties. The influence of the dimensional parameters of glass parts and the presence of surface conductivity in them on the course of the welding process is been determined. It is shown that the welding time required to ensure the connection of KEF-4.5/0.1 silicon with Pyrex glass along the entire contact plane is determined by the peak value of the welding current at the moment of applying the electric welding voltage. The corresponding functional dependencies have been obtained for the first time. The influence of geometrical parameters of welded parts on strength of glass-silicon nodes is been investigated. The results of the experiments showed that with an increase in the ratio of the nominal contact area of the parts to the total perimeter of the side surfaces of the tubular glass part from 0.5 to 1.02 mm2/mm, the welding time increases. Computer simulation of the stress state in the nodes has been carried out. It has been found that in order to improve the performance of welded glass-silicon units by reducing the level of residual stresses, they must be designed so that the ratio of the nominal contact area of the parts to the total perimeter of the side surfaces of the tubular glass part is minimal.

  • Open Access

    CAE Analisis of exploitation of I-beam column with the regulated field of residual stresses in its cross-section

    by Serhii Oleksiienko, Mykhailo Rudenko, Svitlana Yushchenko, Maksym Bolotov, Mykola Korzachenko, Сергій Олексієнко, Михайло Руденко, Світлана Ющенко

    Columns are vertical elements that support the structures on them, perceive the loads and transfer them to the basement. Relatively long elements, the length of which is several times higher rather than its cross-section dimensions, lose their bearing capacity because of stability loss at the stresses that are significantly less than the yield strength of the steel itself. Critical stresses in such elements in each specific case are determined using the longitudinal bending coefficient. The underestimated values of longitudinal bending coefficients are used while calculating the stability of welded elements of solid sections. Residual compressive welding stresses from the belt joints of welded I-beam H-section columns reduce their stability and load-bearing capacity if the residual stresses at the edges of the flanges exceed critical values. If the compressive stresses at the edges of the shelves are reduced by special technological or design means, so then the usual values ​​of the longitudinal bending coefficient can be used in the calculation, which can be an effective means of reducing the material consumption of the product. This paper establishes that the overall stability of compressed elements depends not so much on the magnitude of the welding compressive stresses as on how far from the axis to which the loss of stability is more likely the tensile stress zones are located. Using computer modeling of the stress-strain state that occurs during the operation of welded I-beam columns, the effectiveness of the application of the welding rollers on the edges of the shelves was established. The latter provides for increasing the overall stability of the columns, which has been determined. The zones with tensile stresses are formed on the edges of the shelves after welding of the rollers, and their size will depend on the amount of direct energy during welding. The possibility of reducing the material consumption of columns has been established.

  • Open Access

    PROJECT OF PRISMATIC BUNKER STRUCTURE AND ESTIMATION OF ACCEPTED SOLUTIONS EFFICIENCY

    by Serhii Oleksiienko, Chernihiv Polytechnic National University, Svitlana Yushchenko, Mykhailo Rudenko, Volodymyr Grechka

    The ensuring of the minimum metal consumption of the structure, the reducing the labour-intensiveness of its manufacture and assembly in the construction of steel prismatic bunkers, designed for storage and unloading of free-flowing materials, are entirely determined by the quality of the design structure. The disadvantage of bunker designs is the connection of the side panels at right angles, which causes the unevenness of the stress-strain state and, as a consequence, the occurrence of emergencies. Some studies suggest that one of the main specific causes of bunker breakdowns and damages is related to incorrect determination of structural loads. A number of authors propose the use of multilayer complex design with the utilization of corrugatedsteel sheets, which directed to address the issue of reducing metal consumption. Today there is still no complex approach to solving the problem of ensuring the reliable operation of the structure owing to searching the best structural forms, technologies for its manufacture and assembly.In this connection, the purpose of this work is to develop the design of the prismatic bunker, which allows to ensure operational reliability, production manufacturability and minimal attended costs associated with the construction of the struc-ture on the building site. By means of modeling the stress state in the structures of bunker tanks, the optimal constructive design options were determined, particularly, dimensional parameters and layout of vertical and stiffeningplates.To ensure the operational reliability of bunker tanks, a solution has been developed that provides for the use of stiffening plates in the design of bunker funnel, which ensure the combined work of its sheet part with the stiffening frame. Use of the block principle of construction of bunker tanks allows to increase a degree of factorial readiness of dispatch elements and to reduce labourintensiveness on assembly sites.

  • Open Access

    ЗАСТОСУВАННЯ ТЛІЮЧОГО РОЗРЯДУ В ТЕХНОЛОГІЯХ ВИГОТОВЛЕННЯ ФІБРОБЕТОНУ (ОГЛЯД)

    by Hennadiy Bolotov, Iryna Prybytko, Tymur Hanieiev, Mykola Korzachenko, Svitlana Yushchenko, Геннадій Болотов, Ірина Прибитько, Тимур Ганєєв, Світлана Ющенко

    Розглянуто особливості будови та основні проблеми отримання перспективного виду композиційних будівельних матеріалів – дисперсійно-армованих бетонів (фібробетонів), що складаються з будівельної матриці та армуючих волокон. Проаналізовано результати відомих на даний час досліджень по застосуванню плазми тліючого розряду для обробки поверхонь армуючих волокон з неорганічних та полімерних матеріалів з метою підвищення їх адгезії до матричного матеріалу. Аналіз джерел свідчить, що модифікація поверхонь волокон тліючим розрядом суттєво підвищує міцність зчеплення волокон із будівельним матеріалом і є перспективним технологічним напрямком. Визначено, що обмеженість застосованих способів і режимів плазмової обробки волокон робить доцільним подальше проведення досліджень. Представлена в статті інформація має оглядовий характер.

  • Application of Resistance Welding Machines for Production of Precision Aluminium Joints

    by Oleh O. Novomlynets, Serhii V. Oleksiienko, Svitlana M. Yushchenko, Maksym G. Bolotov, Iryna V. Nahorna

    Electric resistance butt welding of aluminium alloys through thin metal interlayers has been investigated. The effectiveness of using not high capacity resistance welding machines for getting of precision joints has been shown. The technology of resistance butt welding of aluminium alloy 6063 through thin multilayer intermediate layers of aluminium 1050 foil has been developed. The results of microstructure and mechanical strength analysis have been shown.


  • Open Access

    НОВА ТЕХНОЛОГІЯ ЗВАРЮВАННЯ ТИСКОМ АЛЮМІНІЮ З МІДДЮ ЧЕРЕЗ ПРОШАРОК

    by Oleh Novomlynets, Svitlana Yushchenko, Serhii Oleksiienko, Evgen Polovetskiy, Ihor Alekseienko

    Актуальність теми дослідження. Сучасний темп промислового розвитку потребує зниження металоємності конструкцій та одночасного підвищення їхніх технічних характеристик. Використання біметалевих з’єднань у вузлах конструкцій дозволяє поєднати переваги кожного з матеріалів та забезпечити високі експлуатаційні властивості. Одним із найбільш поширених біметалів є пара алюміній-мідь, що широко використовується в різних галузях промисловості. Тому актуальним завданням є пошук нових способів отримання нероз’ємних з’єднань алюмінію з міддю. Постановка проблеми. Отримання якісних нероз’ємних з’єднань різнорідних матеріалів пов’язане з технологічними труднощами, викликаними відмінностями фізико-механічних властивостей матеріалів. Особливо ця проблема ускладнюється в разі необхідності одержання прецизійних з’єднань. Аналіз останніх досліджень і публікацій. Способи зварювання тиском, зокрема електроконтактне, здатні запобігти виникненню вказаних проблем, підвищити міцність з’єднання та досягти прецизійності за рахунок більш низьких температур та меншої тривалості їх дії порівняно зі зварюванням плавленням. У попередніх роботах нами було розроблено технологію прецизійного електроконтактного зварювання алюмінієвих сплавів через тонкий металевий проміжний прошарок. Виділення недосліджених частин загальної проблеми. Недослідженим питанням залишається електроконтактне зварювання алюмінію з міддю через тонкий металевий проміжний прошарок. Постановка завдання. Дослідження здатності до зварювання тиском алюмінію та міді через проміжний прошарок з алюмінієвої фольги з метою отримання з’єднань з високою міцністю та низьким рівнем деформації. Виклад основного матеріалу. Дослідження проводили на зразках із алюмінію АД0 та міді М1 з використанням проміжного прошарку із суцільної стрічки алюмінієвої фольги марки АД0. Шляхом експериментів встановлено оптимальний режим електроконтактного точкового зварювання. Якість зварного з’єднання залежить від кількості шарів фольги в проміжному прошарку. Висновки відповідно до статті. Розроблено технологію зварювання тиском алюмінію та міді через проміжний прошарок з алюмінієвої фольги; встановлено, що використання проміжного прошарку дозволяє збільшити тепловкладення в зону з’єднання та зменшити рівень залишкової деформації; досліджено мікроструктуру зони з’єднання; визначено міцність зварних з’єднань.

  • Stabilization of a High-Current Glow Discharge Under the Welding Conditions

    by Gennady P. Bolotov, Maksym G. Bolotov, Svitlana M. Yushchenko

    The article considers the possibility of increasing stability of DC high-current glow discharge in the diffusion bonding processes at discharge currents 1 ... 30 A and the gas pressure 1.33 ... 13.3 kPa by replacing the monolithic anode with a multi-section one in the running (rotating) electric field. It is shown that the at constant discharge current the using of the 5-section anode assembly with a rotating electric field increases the region of a glow discharge stable existence by 1.5 ... 1.7 times and the energy density in the heating spot in 2.6 ... 2.9 times in comparison with a similar electrode system with the stationary electric field.


  • Open Access

    ЗВАРЮВАННЯ ТИСКОМ АЛЮМІНІЄВИХ СПЛАВІВ ЧЕРЕЗ МОДИФІКОВАНІ ПОВЕРХНЕВІ ШАРИ

    by Oleh Novomlynets, Serhii Oleksiienko, Svitlana Yushchenko, Oleksiy Baydala, Evgen Polovetskiy

    Актуальність теми дослідження. У процесі виробництва та використання виробів складної конфігурації з однорідних та різнорідних матеріалів необхідним завданням є збереження їх проектної форми та забезпечення високих експлуатаційних характеристик, що потребує використання нових технологій прецизійного зварювання тиском. Постановка проблеми. Виготовлення прецизійних деталей та вузлів зварюванням тиском ускладнене наявністю оксидних та адсорбованих плівок і необхідністю активації поверхонь, що зварюються. Аналіз останніх досліджень і публікацій. Раніше нами було встановлено критерії досягнення ефекту прецизійності при зварюванні тиском. Виділення недосліджених раніше частин загальної проблеми. Отримання прецизійних з’єднань зварюванням тиском із використанням проміжних шарів, модифікованих електроіскровим легуванням. Мета роботи. Дослідження здатності до зварювання тиском з обмеженим рівнем деформації металевих матеріалів із попередньою модифікацією поверхневих шарів шляхом електроіскрової обробки. Виклад основного матеріалу. Для модифікації поверхонь алюмінієвих сплавів АД00 та Д1 перед зварюванням використовуються матеріали з високим питомим електричним опором та матеріали, з якими алюміній утворює рідку фазу евтектичного складу при температурі менше температури плавлення алюмінію: титан, цинк, хром, марганець, магній, вуглець, галій, кремній та залізо, у вигляді порошку та прутків. Міцність та деформація зварних з’єднань залежить від електричного опору матеріалу модифікованого шару і, як наслідок, від сили струму обробки. Висновки відповідно до статті. Розроблено методику підготовки поверхонь металів до зварювання шляхом механічного шабрування та модифікації електроіскровою обробкою; електроіскрове легування поверхонь, що зварюються, матеріалом із високим електричним опором локалізує теплову енергію у стику; використання порошкового прошарку з матеріалу з високим електричним опором дозволяє зменшити рівень залишкової деформації.


  • Diffusion bonding technique concerning production of microchannel heat exchangers

    by Serhii V. Oleksiienko, Oleh O. Novomlynets, Svitlana M. Yushchenko

    Diffusion bonding process of aluminium 1070A concerning production of microchannel heat exchangers (MCHE) has been investigated. It has been proposed to raise manufacturability of the process owing to introduction into contact zone of joining details composition on the basis of sodium silicate before welding. The results of investigations of microstructure and chemical composition of welded joints and also mechanical strength of products have been presented.