Fumito Okino
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Fumito Okino has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Juro Yagi
4 shared publicationsTeruya Tanaka
4 shared publicationsSatoshi Konishi
Institute of Advanced Energy, Kyoto University, Gokasho Uji, Kyoto, Japan
3 shared publications- Satoshi Konishi
Kyoto Univ, IInst Adv Energy, Kyoto, Japan
3 shared publications Yukinori Hamaji
3 shared publicationsKazuyuki Noborio
Institute of Advanced Energy, Kyoto University, Uji, Kyoto 611-0011, Japan
2 shared publications
Latest Publications
- 14 July 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 231
Deuterium release from lithium-lead droplets formed under 2.0 mm nozzle flow
- 14 July 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 231
Deuterium release from lithium-lead droplets formed under 2.0 mm nozzle flow
- 3 March 2025
- Published by Elsevier in Fusion Engineering and Design
- Vol. 214
Enhanced deuterium extraction efficiency from lithium-lead droplets in a vacuum
- 3 March 2025
- Published by Elsevier in Fusion Engineering and Design
- Vol. 214
Enhanced deuterium extraction efficiency from lithium-lead droplets in a vacuum
- 15 March 2024
- Published by Elsevier in Fusion Engineering and Design
- Vol. 202
Continuous deuterium extraction from falling lithium-lead droplets in a vacuum
- 15 March 2024
- Published by Elsevier in Fusion Engineering and Design
- Vol. 202
Continuous deuterium extraction from falling lithium-lead droplets in a vacuum
- 12 February 2024
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 80 (8) , 1060-1069
Axial Concentration of Dissolved Deuterium by Dispersion in a LiPb Experimental Loop
- 12 February 2024
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 80 (8) , 1060-1069
Axial Concentration of Dissolved Deuterium by Dispersion in a LiPb Experimental Loop
- 1 November 2020
- Published by Elsevier in Fusion Engineering and Design
- Vol. 160
Emissivity measurement of PbLi droplets in a vacuum for heat recovery by radiation
- 1 November 2020
- Published by Elsevier in Fusion Engineering and Design
- Vol. 160
Emissivity measurement of PbLi droplets in a vacuum for heat recovery by radiation
- 1 September 2019
- Published by Elsevier in Fusion Engineering and Design
- Vol. 146, 898-901
Current status of the continuous tritium recovery test campaign using PbLi droplets in vacuum
- 1 September 2019
- Published by Elsevier in Fusion Engineering and Design
- Vol. 146, 898-901
Current status of the continuous tritium recovery test campaign using PbLi droplets in vacuum
- 1 November 2018
- Published by Elsevier in Fusion Engineering and Design
- Vol. 136, 63-66
Liquid PbLi atomization in vacuum for tritium and heat recovery
- 1 November 2018
- Published by Elsevier in Fusion Engineering and Design
- Vol. 136, 63-66
Liquid PbLi atomization in vacuum for tritium and heat recovery
- 20 April 2017
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 71 (4) , 575-583
Tritium Recovery Efficiency from an Array of PbLi Droplets in Vacuum
Quantitative feasibility analysis of the tritium recovery efficiency from multiple columns of liquid PbLi droplets was conducted.Then a case study based on the HCLL specification was performed. Main concern was whether the experimentally obtained recovery efficiency from a column of droplets is applicable for the efficiency estimation from the multiple columns of droplets without any mutual degrading effects. To maintaining a safe side assumption, the tritium once released and reabsorbed on another droplet was considered to be not re-emitted while falling. By the analogy with the thermal radiation theory, the view factor which expresses the intersection ratio of radiation on another surface was applied for the estimation.The dependences on nozzle design parameters, such as nozzle pitch, number of nozzles, chamber wall clearance, and exhaust port design, were investigated. Case study results suggest that, by choosing well-suited parameters approximately 40% to 60% of the single column recovery efficiency was secured for multiple columns even on the conservative condition. The release chamber exhaust port design had a major influence. Nozzle pitch and array design have less influences, but are not negligible. However, it has to be experimentally verified to the scale-size effects and experimental programs are currently underway.
- 20 April 2017
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 71 (4) , 575-583
Tritium Recovery Efficiency from an Array of PbLi Droplets in Vacuum
Quantitative feasibility analysis of the tritium recovery efficiency from multiple columns of liquid PbLi droplets was conducted.Then a case study based on the HCLL specification was performed. Main concern was whether the experimentally obtained recovery efficiency from a column of droplets is applicable for the efficiency estimation from the multiple columns of droplets without any mutual degrading effects. To maintaining a safe side assumption, the tritium once released and reabsorbed on another droplet was considered to be not re-emitted while falling. By the analogy with the thermal radiation theory, the view factor which expresses the intersection ratio of radiation on another surface was applied for the estimation.The dependences on nozzle design parameters, such as nozzle pitch, number of nozzles, chamber wall clearance, and exhaust port design, were investigated. Case study results suggest that, by choosing well-suited parameters approximately 40% to 60% of the single column recovery efficiency was secured for multiple columns even on the conservative condition. The release chamber exhaust port design had a major influence. Nozzle pitch and array design have less influences, but are not negligible. However, it has to be experimentally verified to the scale-size effects and experimental programs are currently underway.
- Open Access
- 1 September 2013
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 64 (3) , 543-548
Enhanced Mass Transfer of Deuterium Extracted from Falling Liquid Pb-17Li Droplets
Release of deuterium from falling droplets of Pb-17Li in vacuum is experimentally studied. By comparing different diameter nozzle data each other, the effect of ambiguous solution is eliminated, and reliable result is attained. The amount of deuterium that is dissolved into Pb-17Li, followed by the release from the liquid droplets in vacuum, is measured with four different diameter nozzles ranging from 0.4 mm-1.0 mm under an initial velocity of 3.0 m/s and four temperatures between 375 °C and 450 °C. The resultant mass transport, represented by quasi-dispersion-coefficient is 3.4 × 10-7 [m2/s], which is approximately two orders of magnitude faster than previous studies under static condition. It also revealed different temperature dependency. Cyclic deformation of the sphere shape is observed with a high speed movie camera. These results show the falling droplets of liquid Pb-17Li in vacuum follow the mass transfer mechanism under convection prior domain by self-excited oscillation. This result suggests that the tritium recovery method from a breeding liquid Pb-17Li blanket is viable when using multiple nozzles in vacuum for the extraction.
- 1 September 2013
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 64 (3) , 543-548
Open AccessEnhanced Mass Transfer of Deuterium Extracted from Falling Liquid Pb-17Li Droplets
Release of deuterium from falling droplets of Pb-17Li in vacuum is experimentally studied. By comparing different diameter nozzle data each other, the effect of ambiguous solution is eliminated, and reliable result is attained. The amount of deuterium that is dissolved into Pb-17Li, followed by the release from the liquid droplets in vacuum, is measured with four different diameter nozzles ranging from 0.4 mm-1.0 mm under an initial velocity of 3.0 m/s and four temperatures between 375 °C and 450 °C. The resultant mass transport, represented by quasi-dispersion-coefficient is 3.4 × 10-7 [m2/s], which is approximately two orders of magnitude faster than previous studies under static condition. It also revealed different temperature dependency. Cyclic deformation of the sphere shape is observed with a high speed movie camera. These results show the falling droplets of liquid Pb-17Li in vacuum follow the mass transfer mechanism under convection prior domain by self-excited oscillation. This result suggests that the tritium recovery method from a breeding liquid Pb-17Li blanket is viable when using multiple nozzles in vacuum for the extraction.
- 31 August 2012
- Published by Elsevier in Fusion Engineering and Design
- Vol. 87 (7-8) , 1014-1018
Vacuum sieve tray for tritium extraction from liquid Pb–17Li
- 31 August 2012
- Published by Elsevier in Fusion Engineering and Design
- Vol. 87 (7-8) , 1014-1018
Vacuum sieve tray for tritium extraction from liquid Pb–17Li